KA1000 is designed to work with only the power source indicated on the back of the unit. If you are not sure about your house power source, please consult with your electric company and contact your Krown local dealer to obtain or exchange a correct voltage unit to use.
Notice: the Canadian Department of communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective operational and safety requirements. The Department does not guarantee that the equipment will operate to the user’s satisfaction. Before installing this equip- ment, the users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.
Page 5
REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.] e) If this equipment KA1000 causes harm to the telephone network, the telephone com- pany will notify you in advance that temporary discontinuance of service may be re- quired.
INTRODUCTION Thank you for your purchase of dual alarm clock KA1000- the best design in alarm and monitoring systems but easy and simple to set up and use. The alarm clock will trigger either the bed shaker, table lamp, or sound to absolutely wake you up every morning. You could select a combination of sound and light or shaker and light to fit your lifestyle.
KA1000 DUAL ALARM CLOCK Night lamp Snooze button Time button Time Snooze Security timer button Hour Alarm 1 button Minutes Alarm 2 button AM/PM Alarm 1/2/Security A LA 1 A LA 2 S C T A LA R Alarm Notification...
A. Dual Alarm Clock KA1000: The best location to set the alarm clock KA1000 is next by the table lamp and close by the telephone outlet in your bedroom. It also can be used in your living room or kitchen where a lamp is available and be seen at many angles.
The door knock, telephone ringer and baby room call will be installed in channel 2 (C2). Other monitoring transmitter will be installed in channel 1 (C1). The dip switch code of each transmitter will be stored in KA1000 channel memory indicated by: CX:OX -> MEMORY LOCATION Registering the door knock with the KA1000: 1.
If you are not home for a long extended period of time, and you want it to look like some- one is still at home, you can use the security timer feature. Every night, the clock KA1000 can turn on the table lamp connected to it for you and turn it off later at 11 pm. To pick starting time: 1.
Alarm: Turns on when the alarm clock is triggered. Battery: KA1000 will operate on one 8.4VDC rechargeable battery during a power outage. Do not use a regular battery. Power is provided for the sound and the shaker only. The clock display is blank but the time is still maintained.
ACCESSORIES The dual alarm clock system is designed to work in correspondence with other wireless receivers and work with all KA300 transmitters (sold separately). Select from the following to complete your system. A. Extended receiver: (KA1000EX) Turn on the lamp and plug into the extended receiver. Plug the extended receiver into an AC outlet and the light will flash to notify you everywhere it is placed: kitchen, living room, bathroom etc.
ON position or it will not flash the light. * The alarm function of the alarm clock KA1000 will not trigger the extended receiver. * The extended receiver is on stand-alone unit and receives signals directly from a transmitter. It does not need a KA1000 clock to operate.
The KA300 wireless alarm monitor system is designed to link all of the alarms in your house together. It works with the KA1000 dual alarm clock with bed shaker and table lamp. The KA300RX receiver comes with very strong flash light 177Cd and 95dB loud siren.
TEST AND TROUBLESHOOTING Testing: Testing the KA1000 every night before you go to bed is recommended to guaranty it will wake you up in the morning. Slide the test switch to the “Test” position and watch for the system send out a signal to the shaker, speaker, and lamp.
11. The clock activates the door knock or telephone ringer but there is no one at the door or the telephone did not ring: Your neighbor may also be using the KA1000. Change the security code on the transmitter and register with the clock again. (Please read change system security code section page 9) 12.
fitness and of any obligation on the part of Krown Manufacturing, Inc. If the Alarm Clock shall prove the defective, then Krown Manufacturing, Inc shall either replace or repair the Alarm Clock at no cost to the original purchaser within one year of the date of purchase.
Page 19
Record the security code or dip switch with channel jumper of all installed transmitters to this sheet. Use these codes to setup the new transmitters or register them to KA1000 and KA1000EX. You will achieve the same flash pattern if you register the transmitter in the same order.
Need help?
Do you have a question about the KA1000 and is the answer not in the manual?
Questions and answers