Uniden DHS100 User Manual

DHS100 Cordless Headset User's Guide
Cordless
headset with
earpiece loop
and ear cap
attached
Charge cradle
x If any items are missing or damaged, contact our Customer Care
Line immediately. Never use damaged products!
x Need Help? Get answers 24/7 at our website: www.uniden.com.
If You...
have a question or problem
need a part or accessory
need special assistance due
to a disability
* During regular business hours, Central Standard Time. Visit our website for detailed
business hours.

Important Safety Instructions!

When using your telephone equipment, basic safety precautions should always be
followed to reduce the risk of fire, electric shock and injury to persons, including the
following:
x This unit is NOT waterproof. DO NOT expose this unit to rain or moisture.
x Do not use this product near water, for example, near a bath tub, wash bowl, kitchen
sink or laundry tub, in a wet basement or near a swimming pool.
x Avoid using a telephone (other than a cordless type) during an electrical storm. There
may be a remote risk of electric shock from lightning.
x Do not use the telephone to report a gas leak in the vicinity of the leak.

PreParING YoUr HeaDSet

attach earpiece Loop or Headband
x Choose the appropriate size Earpiece Loop.
x Push the selected Earpiece Loop or Headband
eyelet onto headset mounting peg.

Charge the Battery

1. Connect the AC adapter to the
charge cradle jack and to a wall
outlet.
2. Place the headset in the charging
cradle with the status LED
facing forward. If the LED
doesn't light up, reseat the
headset or connect the charger
to a different outlet.
3. When the headset is fully charged, the status LED will show blue.
#
Charge the headset completely (about 3 hours) before using it.
#
Do not charge the headset when the ambient temperature is below
0° C (32°F) or above 40°C (104°F).

reGISterING to a BaSe

#
the accessory headset won't work until you register it to a
compatible Uniden cordless phone!
Compatible Uniden Cordless Phones
Find compatible models at our website: www.uniden.com.
register the Headset
1. On the phone base, press and hold
#
on some models (such as the D3588) press
from the display menu selection, and then press
2. On the headset, press and hold both
The status LED alternately blinks slow to fast blue and red while registering.
When registered, a confirmation tone sounds at the phone base and the
headset LED flashes blue once every 10 seconds.
test the connection
Pick up the headset and press ON/OFF/TAlK . Listen for a dial tone. (Press ON/
to hang up.)
OFF/TAlK
If...
x there is no dial tone
x the error tone sounds
oPeratIoN
to power on...
x press and hold ON/OFF/TAlK for 3
seconds .
to answer a call...
x press ON/OFF/TAlK and speak clearly
x press ON/OFF/TAlK again to end call
to mute the microphone...
x press MUTE/FlASH to mute
x press MUTE/FlASH again to unmute

ImPortaNt INFormatIoN

aC adapter and Battery Specifications
aC adapter
Part number
PS-0045
x Use only the supplied AC adapter.
x Do not place the unit in direct sunlight or subject it to high temperatures.
Battery information (battery is not user-replaceable)
Type
Lithium-ion
x Please contact Uniden Customer Service if the battery fails.
x When the battery gets low, the headset sounds an alert tone and the status indicator shows red
once every 10 seconds to indicate the unit needs charging.

General InformatIon

• You cannot use the headset while it is charging.
• Actual range varies depending environmental conditions and battery power level.

Cleaning the headset

If necessary, remove the Ear Cap and Earpiece loop. Dampen a lint-free cloth with water or
a cleaner specially designed for electronics, and gently wipe the headset clean.
Do not expose this product to liquid (water, alcohol, etc.) or
submerse in liquid for any reason.

What's in the box?

Additional
earpiece loop (1)
SAVE THESE INSTRUCTIONS!
Input voltage
120VAC, 60 Hz
Capacity
230mAh, 3.7VDC
Headband
Contact Uniden's...
Customer Care Line*
Parts Department*
Accessibility Help Line
MUTE/FLASH
FIND HANDSET
VOlUME -
try...
charging the headset until fully
charged and then retry connection.
to power off...
x press and hold ON/OFF/TAlK for 3
seconds .
to adjust call or ringer volume...
call (in use) or ringer (standby):
x press + to increase or – to decrease
to answer call waiting call...
x press and hold MUTE/FlASH
x press and hold MUTE/FlASH to return
Talk time
about 6 hours
AC adapter
(PS-0045)
Additional ear caps (2)
Phone Number
817-858-2929 or
800-297-1023
800-554-3988
800-874-9314
(voice or TTY)
Earloop
ON/OFF/TALK
VOLUME +/-
STATUS LED
for 5 seconds.
, select
Register handset
MENU
SElEcT.
and for 5 seconds.
+
Output voltage
5.4VDC @ 400mA
Standby time
about 3 days
Headset peg
Earloop
eyelet