Infinity 10" Dual Voice-Coil Subwoofer Beta Ten.dvc Instructions

B T . 2-O (P ) W
ETA EN DVC HM ARALLEL IRING
Beta Ten.dvc
(rear view)
+
+ –
From
®
Amp
Output
– +
–
B T . 8-O (S ) W
ETA EN DVC HM ERIES IRING
Beta Ten.dvc
(rear view)
+
+
–
From
®
Amp
Output
+
–
–
B T . S -M W
ETA EN DVC UMMED ONO IRING
Beta Ten.dvc
(rear view)
–
From From
Left Right
Amp Amp
Output Output
+
Infinity Systems, Inc. • 20630 Nordhoff Street
Chatsworth, CA 91311, USA • VOICE (818) 407- 0228 • FAX (818) 709 -9486
®
B T . D -S W
ETA EN DVC UAL UBWOOFER
(Dual) Beta Ten.dvc
(rear view)
+
+ –
From
Amp ®
Output
– – +
METHOD #1
(Dual) Beta Ten.dvc
(rear view)
+
+ –
From
Amp ®
Output
– +
–
METHOD #2
IMPORTANT: When connecting two Beta
Ten.dvc subwoofers together, use Method #1 to
create a net 4-ohm impedance. NEVER USE
METHOD #2, since most amplifiers cannot fully
control driver movement in this configuration.

DECLARATION OF CONFORMITY

+
We, Infinity Systems A/S
Kongevejen 194B
DK-3460 Birkerød
DENMARK
declare in own responsibility, that the Beta Ten.dvc subwoofer
is in compliance with technical standards
EN 50 081-1/1992 and EN 50 082-1/3.1995
–
IRING
CAR AUDIO
+ –
Thank you for purchasing an Infinity Beta Ten.dvc
10" Dual Voice-Coil Subwoofer. You've selected a
®
premium product that offers superior performance
and advanced materials, resulting from over 25
– +
years of loudspeaker design. This Infinity product is
made with our ongoing dedication to create the best
consumer audio products possible. As a result, you
can expect your new Beta Subwoofer to provide you
with many years of listening enjoyment.
Refer to Subwoofer Enclosure Trade-Offs (on the
inside pages) for help in selecting an enclosure type
and alignment. Also, review the wiring diagrams (on
the back page) on how to connect the subwoofer for
+ –
2-ohm, 8-ohm, and summed-mono applications.
®
Each Infinity Beta Ten.dvc 10" Dual Voice-Coil
Subwoofer is covered by our limited parts and labor
– +
warranty (see the enclosed warranty card). Keep
your original dated bill of sale in case warranty ser-
vice is required.
IMPORTANT: Installation of automotive stereo
components can require extensive experience in
dealing with a variety of electrical, and
mechanical procedures, including subwoofer
box building. Although these instructions
explain how to install a Beta Subwoofer in a
general sense, they do not show the exact instal-
lation methods for your particular vehicle. If
you do not have the experience, do not attempt
the installation yourself; instead ask your
Authorized Infinity Car Audio Dealer about
professional installation options.
P
RECAUTIONS
• Always wear protective eyewear when using tools.
• Turn off all audio systems and other electrical
devices before starting the installation.
• Disconnect the (–) negative lead from your vehi-
cle's battery.
Steen Michaelsen
Infinity Systems A/S
Birkerød. DENMARK. 4/96
Printed In Japan
I N S T R U C T I O N S
• Locate and note all fuel lines, hydraulic brake
lines, and electrical wiring. Use extreme caution
when cutting or drilling in and around these areas.
• Check clearances on both sides of a planned
mounting surface before drilling any holes or
installing any screws.
T -S
HIELE
F -A R
REE IR ESONANCE
C V
OMPLIANCE
M
ECHANICAL
E Q:
LECTRICAL
T Q:
OTAL
M E
AXIMUM XCURSION
V C D
OICE OIL
S
PECIFICATIONS
D :
IAMETER
S (2.83 V @ 1
ENSITIVITY
P H
OWER ANDLING
F R
REQUENCY
N I
OMINAL MPEDANCE
D :
IMENSIONS
Infinity Systems, Inc. • 20630 Nordhoff Street
Chatsworth, CA 91311, USA • VOICE (818) 407- 0228 • FAX (818) 709 -9486
®
Ten.dvc 10" S u b w o o f e r
P
MALL ARAMETERS
: F (H ) 24.00
Z
S
FT 3
: V ( ) 2.70
OLUME
AS
V ( ) 77.00
LITERS
AS
Q: Q 8.08
MS
Q 0.20
ES
Q 0.20
TS
: X ( ) 0.39
IN
MAX
X ( ) 10.00
MM
MAX
R : R ( ) 2.80
C ESISTANCE OHMS
E
10" (254.0 )
MM
): 93 dB
M
: 250 W
RMS PER VOICE COIL
: 20 ~ 500 H
ESPONSE Z
: 4
OHMS PER VOICE COIL
mounting depth
4.75" (120.65 mm)
cutout diameter
9.37" (238.00 mm)
outer diameter
10.70" (271.78 mm)