4 ohm @ rated power 19 Amps 2 ohm @ rated power 34 Amps Infinity continually strives to update and improve existing products, as well as create new ones. The specifications and details in this and related JBL publications are therefore subject to change without notice.
Amplifier Expansion Module BassLink 4sc ONNECTIONS Note: In order for the Phantom Center circuit to INPUT CONNECTIONS If your source unit provides only speaker-level Note: If your source unit provides two line-level operate properly, the speakers and input wires You must connect full-range signal to all four...
BASSLINK 4sc BASSLINK II Figure 7. Figure 4. REMOTE LEVEL controls. Figure 5. BassLink 4sc controls. Figure 6. BassLink II controls on the front panel. SUB LEVEL: Use this control to adjust the PHANTOM CENTER: Use this switch to select the amount of bass to suit your preference.
Using the Phantom Center Setup CD (included SUBWOOFER LEVELS level control) to its maximum output setting with your BassLink 4sc) you’ll listen to some (fully clockwise). instructions, a spoken setup track and several Note: In order for the Phantom Center to work music selections to determine the best adjustment Note: Refer to page 4, ”Controls and Functions, ”...
Page 6
Amplifier Expansion Module BassLink 4sc UNING CONTINUED Tracks 5 through 16 are music tracks. There PHANTOM CENTER SETUP CD SETTING THE PHANTOM CENTER CIRCUIT ADDING THE SOUND FROM THE REAR are three excerpts of songs and each excerpt Track 1 Introduction 1.
• PROBLEM: • PROBLEM: BassLink II and 4sc Power LEDs are not lit. BassLink 4sc Power LED lit but no sound from No output from BassLink II when head-unit one or all speakers. fader control is set to front or rear (in a CAUSES and SOLUTIONS: 4-channel connection).
Amplifier Expansion Module BassLink 4sc 2 ohm/4 ohm HP filter 80Hz 12dB L/OFF/R Phantom Left SPEAKER Gain Remote control Circuit Control Channel select 3 pos swtw/off Front Circuit HP filter 200Hz/400Hz/800Hz/off 80Hz 12dB 2 ohm/4 ohm Right Remote control SPEAKER...
Amplifier Expansion Module BassLink 4sc BASSLINK 4sc Electrical Parts List Part Number Description Reference Designators Note on Numbering Sequence, all components: "D510~519" (tilde mark) means D510,511,512,513,514,…etc. but "Q135-Q435" (hyphen) means Q135,235,335,435" POWER SUPPLY/MAIN/FACEPLATE PCB Semiconductors 100T0SA06 4 Q140-Q440 SMD Transistor...
Page 10
Amplifier Expansion Module BassLink 4sc Part Number Description Reference Designators Note on Numbering Sequence, all components: "D510~519" (tilde mark) means D510,511,512,513,514,…etc. but "Q135-Q435" (hyphen) means Q135,235,335,435" POWER SUPPLY/MAIN/FACEPLATE PCB R39 R43 R501~R515 R518~528 R529~530 290T63103 SMD Resistor SMD(0603) 10K 5%...
Page 11
Amplifier Expansion Module BassLink 4sc Part Number Description Reference Designators Note on Numbering Sequence, all components: "D510~519" (tilde mark) means D510,511,512,513,514,…etc. but "Q135-Q435" (hyphen) means Q135,235,335,435" POWER SUPPLY/MAIN/FACEPLATE PCB 532T25009 9PIN 1 J1 Terminal 535T20012 Terminal 12P P=2.0mm 180 1 J3...
Page 12
Amplifier Expansion Module BassLink 4sc Part Number Description Reference Designators Note on Numbering Sequence, all components: "D510~519" (tilde mark) means D510,511,512,513,514,…etc. but "Q135-Q435" (hyphen) means Q135,235,335,435" PWM (Power) PCB Capacitors 301T10463 SMD Capacitor SMD(0603) 0.1UF/50V 20% 1 C6 301T68263 SMD Capacitor...
Need help?
Do you have a question about the BassLink 4sc and is the answer not in the manual?
Questions and answers