Magnavox CT202MW8 Service Manual

20" analog/digital pure flat color tv/dvd/vc

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

SERVICE MANUAL

Main Section

I Specifications

I Preparation for Servicing

I Adjustment Procedures

I Schematic Diagrams

I CBA's

I Exploded Views

I Parts List

20" ANALOG/DIGITAL

PURE FLAT COLOR TV/DVD/VCR

CT202MW8

When servicing the deck

mechanism, refer to MK14 Deck

Mechanism Section.

Deck Mechanism Part No.:

N2466FT

Table of Contents

Summary of Contents for Magnavox CT202MW8

Page 1: Service Manual
When servicing the deck I Specifications mechanism, refer to MK14 Deck I Preparation for Servicing Mechanism Section. I Adjustment Procedures I Schematic Diagrams Deck Mechanism Part No.: I CBA’s I Exploded Views N2466FT I Parts List 20″ ANALOG/DIGITAL PURE FLAT COLOR TV/DVD/VCR CT202MW8...
Page 2: Important Safety Notice
IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.
Page 3: Table Of Contents
MAIN SECTION 20″ ANALOG/DIGITAL PURE FLAT COLOR TV/DVD/VCR CT202MW8 Main Section I Specifications I Preparation for Servicing I Adjustment Procedures I Schematic Diagrams I CBA’s I Exploded Views I Parts List TABLE OF CONTENTS Specifications ................1-1-1 Laser Beam Safety Precautions .
Page 4: Specifications
SPECIFICATIONS *ˆ Mode---------SP mode unless otherwise specified * Test input terminal <Except Tuner>--------Video input (1 Vp-p) Audio input (-10 dB) <Tuner>------------------Ant. input (80 dBµV) Video: 87.5% Audio: 25 kHz dev. (1 kHz Sin) < DEFLECTION > Description Condition Unit Nominal Limit Horizontal ±5...
Page 5 < TUNER > Measurement at Speaker (Audio), TP1401 (Video) Description Condition Unit Nominal Limit 1. Video S/N (80 dBµV, TV4ch) 2. Audio S/N (W/LPF, 15 kHz dev.) < VCR > Measurement at TP1401 (Video) Description Condition Unit Nominal Limit 1. Horizontal Resolution (R/P, SP) Line µs...
Page 6 < ATSC > Measurement at Speaker (Audio) Description Condition Unit Nominal Limit >100 1. RECEIVED FREQ. RANGE (-28dBm) – >100 2. ATSC DYNAMIC RANGE (min./max.) VHF LOW BAND. CH.4 dBµV 26/114 32/108 VHF HI BAND. CH.10 dBµV 26/114 32/108 UHF BAND. CH.41 dBµV 28/118 34/112...
Page 7: Laser Beam Safety Precautions
LASER BEAM SAFETY PRECAUTIONS This DVD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on.
Page 8: Important Safety Precautions
IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
Page 9 Also, because the picture tube shields and an isolation transformer only if the AC power mounting hardware perform an X-radiation plug is inserted so that the chassis is protection function, they must be correctly in connected to the ground side of the AC power place.
Page 10 of the countries in which they are to be sold. 2) Strip about 15 mm of the insulation from the However, in order to maintain such compliance, it ends of the wires. If the wires are stranded, is equally important to implement the following twist the strands to avoid frayed conductors.
Page 11 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1.
Page 12: Standard Notes For Servicing
STANDARD NOTES FOR SERVICING Circuit Board Indications Pb (Lead) Free Solder 1. The output pin of the 3 pin Regulator ICs is Pb free mark will be found on PCBs which use Pb indicated as shown. free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder.
Page 13 around the flat pack-IC to protect other parts from With Soldering Iron: damage. (Fig. S-1-2) 1. Using desoldering braid, remove the solder from 3. The flat pack-IC on the CBA is affixed with glue, so all pins of the flat pack-IC. When you use solder be careful not to break or damage the foil of each flux which is applied to all pins of the flat pack-IC, pin or the solder lands under the IC when...
Page 14 2. Installation With Iron Wire: 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
Page 15: Instructions For Handling Semi- Conductors
Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
Page 16: Preparation For Servicing
PREPARATION FOR SERVICING How to Enter Service Mode Adjustment Mode Caution 1: Head switching position adjustment: See adjustment instructions. 1. Optical sensors system are used for Tape Start and End Sensor on this equipment. Read this YUV Brightness up adjustment mode in page carefully and prepare as described on this DTV mode: page before starting to service;...
Page 17: Cabinet Disassembly Instructions
CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart Removal Step/ This flowchart indicates the disassembly steps for the Remove/*Unhook/ Loc. Part Fig. Unlock/Release/ cabinet parts, and the CBA in order to gain access to Note Unplug/Unclamp/ item(s) to be serviced. When reassembling, follow the Desolder steps in reverse order.
Page 18 Reference Notes in the Table To avoid damage of pickup follow the next procedures. CAUTION! 1) Disconnect Connector (CN301) on the DVD When removing the CRT, be sure to discharge the Main CBA Unit. Anode Lead of the CRT with the CRT Ground Wire 2) Short the three short lands of the FPC cable before removing the Anode Cap.
Page 19 [2] Tray Chassis Unit (S-8) (S-5) Top Shield (S-5) [4] DVD (S-8) Mechanism (S-9) (S-9) (S-9) Module PCB Holder [5] DVD Main [8] Deck CBA Unit Assembly (S-6) (S-12) (S-12) (S-6) [10] DTV (S-6) (S-7) Module CBA Unit [6] Sub CBA [7] Function [9] Main CBA (S-10)
Page 20 Anode Cap (S-4) CRT CBA (S-4) (S-4) [3] CRT (S-4) Fig. D3 DVD Mechanism Short the three short lands by soldering. (Either of two places.) View for A FPC Cable Fig. D4 1-6-4 P7752DC...
Page 21 DVD Main CBA Unit CN301 Junction-B CN201 TO SPEAKER CN2A CN1A CL3801 ANODE CN3801 CN2801 CN2571 Function CL2501A Sub CBA CL2504A CN2401 CN2301 CN2302 CN2103 Main CBA CL1403 CN1301 CN1302 CN1103 CN1104 CL2504B CRT CBA CN2501 CL1401 CL2501B AC CORD CL1402 CN1601 TUNER...
Page 22: Electrical Adjustment Instructions
ELECTRICAL ADJUSTMENT INSTRUCTIONS General Note: “CBA” is abbreviation for How to enter Service mode: “Circuit Board Assembly.” Service mode: Note: Electrical adjustments are required after 1. Use the service remote control unit. replacing circuit components and certain mechanical parts. It is important to perform 2.
Page 23 2. Setting for CONTRAST, COLOR, YC-COLOR (YC-COL) 1. Press [2] button to select “YC-COLOR (YC-COL)” TINT, V-TINT and SHARPNESS display. Data Values 2. Press [CH. o/p] buttons so that the value of “YC- COLOR (YC-COL)” becomes “70”. <TV mode (Composite block)> 1.
Page 24 3. C-Trap Adjustment 4. H f Adjustment Purpose: To get minimum leakage of the color signal Purpose: To get correct horizontal position and size of carrier. screen image. Symptom of Misadjustment: If C-Trap Adjustment is Symptom of Misadjustment: Horizontal position and incorrect, stripes will appear on the screen.
Page 25: White Balance Adjustment
5. Cut-off/Drive Adjustment to step 7 when the Green Cut off adjustment is done. Purpose: To adjust the beam current of R, G, B, and 7. Press [3] button on the service remote control unit screen voltage. and select "COB" mode. The display will momentarily show "COB".
Page 26: Focus Adjustment
8. Focus Adjustment 9. Adjust Red and Blue color so that the temperature becomes 9200K (x: 286 / y: 294) ±3%. Purpose: Set the optimum Focus. 10. At this time, check if horizontal line is white. If not, adjust Cut-off Adjustment until the horizontal line Symptom of Misadjustment: If Focus Adjustment is becomes pure white.
Page 27 10. V. Position Adjustment 12. Head Switching Position Adjustment Purpose: To obtain correct vertical position of screen image. Purpose: Determine the Head Switching Position during Playback. Symptom of Misadjustment: If V. position is incorrect, vertical position of image on the screen may Symptom of Misadjustment: May cause Head not be properly displayed.
Page 28: Convergence Adjustment
14. Convergence Adjustment The following 2 adjustments normally are not attempted in the field. They should be done only Purpose: To obtain proper convergence of red, green when replacing the CRT then adjust as a and blue beams. preparation. Symptom of Misadjustment: If Convergence 13.
Page 29 4. Fix the C.P. Magnets by tightening the Ring Lock. 5. Remove the DY Wedges and slightly tilt the Deflection Yoke horizontally and vertically to obtain the best overall convergence. 6. Fix the Deflection Yoke by carefully inserting the DY Wedges between CRT and Deflection Yoke. 1-7-8 P7753EA...
Page 30: How To Initialize The Tv/Dvd/Vcr
HOW TO INITIALIZE THE TV/DVD/VCR To put the program back at the factory-default, initialize the TV/DVD/VCR as the following procedure. < DVD Section > < TV/VCR Section > 1. Turn the power on and press [SELECT] button on 1. Use the service remote control unit. the remote control unit to put the TV/DVD/VCR 2.
Page 31: Firmware Renewal Mode
FIRMWARE RENEWAL MODE 1. Turn the power on and press [SELECT] button on " ******* " differs depending on the models. the remote control unit to put the TV/DVD/VCR into DVD mode. Then remove the disc on the tray. F/W Version Up Mode Model No : ******* (It is possible to move to F/W version up mode VERSION : *.**...
Page 32: Block Diagrams
BLOCK DIAGRAMS < TV/VCR Section > System Control / Servo Block Diagram 1-10-1 P7754BLS...
Page 33 Video Block Diagram 1-10-2 P7754BLV...
Page 34 Audio Block Diagram 1-10-3 P7754BLA...
Page 35 Hi-Fi Audio Block Diagram 1-10-4 P7754BLH...
Page 36 TV Process Block Diagram 1-10-5 P7754BLT...
Page 37 DTV Block Diagram 1-10-6 P7754BLDT...
Page 38 CRT/H.V. Block Diagram 1-10-7 P7754BLCRT...
Page 39 Power Supply Block Diagram 1-10-8 P7754BLP...
Page 40 BLOCK DIAGRAMS < DVD Section > DVD System Control / Servo Block Diagram 1-10-9 P7754BLSD...
Page 41 Digital Signal Process Block Diagram 1-10-10 P7754BLD...
Page 42: Schematic Diagrams / Cba's And Test Points
SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Page 43 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V. 2.
Page 44 Main 1/6 & Sensor Schematic Diagram < TV/VCR Section > P7754SCM1 1-11-3...
Page 45 Main 2/6 Schematic Diagram < TV/VCR Section > P7754SCM2 1-11-4...
Page 46 Main 3/6 Schematic Diagram < TV/VCR Section > P7754SCM3 1-11-5...
Page 47 Main 4/6 Schematic Diagram < TV/VCR Section > 1-11-6 P7754SCM4...
Page 48 Main 5/6 & Junction-A Schematic Diagram < TV/VCR Section > P7754SCM5 1-11-7...
Page 49 Main 6/6 Schematic Diagram < TV/VCR Section > VOLTAGE CHART (Power off mode) Ref. No. IC1601 CAUTION ! IC1901 Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, IC1902 11.3 10.3...
Page 50 Sub 1/3 Schematic Diagram < TV/VCR Section > 1-11-9 P7754SCSUB1...
Page 51 Sub 2/3 Schematic Diagram < TV/VCR Section > P7754SCSUB2 1-11-10...
Page 52 Sub 3/3 Schematic Diagram < TV/VCR Section > 1-11-11 P7754SCSUB3...
Page 53 CRT Schematic Diagram < TV/VCR Section > P7754SCCRT Function & Junction-B Schematic Diagram < TV/VCR Section > P7754SCF 1-11-12...
Page 54 DTV Module 1/2 Schematic Diagram < TV/VCR Section > P7754SCDT1 1-11-13...
Page 55 DTV Module 2/2 Schematic Diagram < TV/VCR Section > VOLTAGE CHART CN101 Pin No. Voltage CN102 Pin No. Voltage P7754SCDT2 1-11-14...
Page 56 DVD Main 1/3 Schematic Diagram < DVD Section > 1-11-15 P7754SCD1...
Page 57 DVD Main 2/3 Schematic Diagram < DVD Section > P7754SCD2 1-11-16...
Page 58 DVD Main 3/3 Schematic Diagram < DVD Section > 1-11-17 P7754SCD3...
Page 59 Sensor CBA Top View Main CBA Top View < TV/VCR Section > CAUTION ! Because a hot chassis ground is present in the power CAUTION ! : For continued protection against risk of fire, Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. BHF300F01011A supply circuit, an isolation transformer must be used.
Page 60 Main CBA Bottom View < TV/VCR Section > CAUTION ! Because a hot chassis ground is present in the power CAUTION ! : For continued protection against risk of fire, Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. supply circuit, an isolation transformer must be used.
Page 61 Sub CBA Top View < TV/VCR Section > TP2501 TP1301 BLUE TP2504 R2583 (H f Adjustment) BP7750F01021-A 1-11-20...
Page 62 Sub CBA Bottom View < TV/VCR Section > WF17 PIN 8 OF CN2 WF18 PIN 6 OF CN2 WF20 PIN 1 OF CN2 WF19 PIN 4 OF CN2 TP2503 H-DRIVE WF11 PIN 5 OF CN2571 WF10 Q2571 Collector 1-11-21 BP7750F01021-A...
Page 63 CRT CBA Top View < TV/VCR Section > CRT CBA Bottom View < TV/VCR Section > WF14 WF12 WF13 Q2501 Q2502 Q2503 Collector Collector Collector BP7750F01021-B 1-11-22...
Page 64 Function CBA Top View < TV/VCR Section > Junction-A CBA Junction-A CBA Top View Bottom View < TV/VCR Section > < TV/VCR Section > BP7750F01021-D Junction-B CBA Junction-B CBA Top View Bottom View < TV/VCR Section > < TV/VCR Section > Function CBA Bottom View <...
Page 65: Waveforms
WAVEFORMS X8TWF 1-12-1...
Page 66: Wiring Diagram
WIRING DIAGRAM < TV/VCR Section > P7754WIT 1-13-1...
Page 67 WIRING DIAGRAM < DVD Section > P7754WID 1-13-2...
Page 68: System Control Timing Charts
SYSTEM CONTROL TIMING CHARTS < TV/VCR Section > Mode SW: LD-SW LD-SW Position detection A/D Input voltage Limit Symbol (Calculated voltage) 3.76 V ~ 4.50 V (4.12 V) 4.51 V ~ 5.00 V (5.00 V) 0.00 V ~ 0.25 V (0.00 V) 1.06 V ~ 1.50 V (1.21 V) 0.66 V ~ 1.05 V (0.91 V) 1.99 V ~ 2.60 V (2.17 V)
Page 69 Chart 1 1) SP MODE 18 RF-SW The first rise of RF-SW after a rise in F-AD signal. F-AD ( Internal Signal ) "H" "H" "Z" C-DRIVE Stop Detection Acceleration Detection Slow Tracking Value PB CTL Reversal Limit Value 66 C-F/R ROLL COMPENSATION (DRUM SERVO)
Page 70 Chart 2 2) LP/EP MODE 18 RF-SW The first rise of RF-SW after a rise in F-AD signal. F-AD ( Internal Signal ) "H" "H" "Z" C-DRIVE Stop Detection Acceleration Detection Slow Tracking Value PB CTL Reversal Limit Value 66 C-F/R ROLL COMPENSATION (DRUM SERVO)
Page 71 Chart 3 EJECT ST-S/ END-S "OFF" CASS.LOAD LD-FWD 0.2S LD-REV SFT-SW STOP(B) POWER LD-FWD 0.4S 0.2S LD-REV 0.2S LD-FWD 0.5S LD-REV STOP(A) PLAY LD-FWD PLAY LD-FWD RS1(RS2) LD-REV 0.2S LD-FWD FS1(FS2) PLAY PLAY PAUSE (SLOW) LD-FWD STILL(SLOW) PLAY LD-REV 0.2S LD-FWD PLAY STOP...
Page 72 Chart 4 STOP(A) STOP LD-REV 0.2S LD-FWD 0.2S STOP /EJECT 1.0S LD-FWD 0.5S LD-REV STOP(A) LD-REV 0.2S LD-FWD 0.2S STOP /EJECT LD-REV 1.0S LD-FWD 0.5S LD-REV STOP(A) LD-FWD PAUSE LD-FWD 2.5S Short REV LD-REV 0.2S LD-FWD REC PAUSE REC or PAUSE STOP /EJECT...
Page 73 < DVD Section > Tray Close ~ Play / Play ~ Tray Open Tray Disc Disc Tray Play Close Rotation Stop Open 3.3V Tray IN (TL221) Sled Drive 1.65V (TP303) Disc Drive 1.65V (TP301) 1.65V Focus Drive (TP304) Tracking Drive 1.65V (TP302) 1-14-6...
Page 74: Ic Pin Function Descriptions
IC PIN FUNCTION DESCRIPTIONS IC1201 (TV/VCR Micro Controller IC) Signal Name Function Signal Name Function Record Protection Tab 33 REC-SAFETY Detection LD-SW Loading Switch Input System Reset Signal (Reset = 34 RESET DVD-LED DVD LED Control Output “L”) Power Supply Failure 35 XC-IN Sub Clock (32kHz) P-SAFETY 2...
Page 75 Signal Name Function 70 YCA-SCL YCA Serial Clock 71 SCL Serial Clock 72 SDA Serial Data Capstan Motor FWD/REV 73 C-F/R Control Signal 74 C-SYNC Composite Sync Input 75 P-ON-H2 Power On Signal at High 76 C-CONT Capstan Motor Control Signal 77 D-CONT Drum Motor Control Signal Power Supply Failure...
Page 76: Lead Identifications
LEAD IDENTIFICATIONS 2SK3563 MID-32A22F 2SK3757(Q) KRA103M-AT/P 2SA950-O(TE2 F T) 2SC2120-O(TE2 F T) KRC103M-AT/P 2SC1627-Y(TE2.F.T) KTA1267-GR-AT/P 2SC2482 KTC3199-GR-AT/P 2SC3331(T) KTC3199-Y-AT/P 2SD400(F) G D S E C B E C B AN17812A LA78040A 2SC5885000RF TLV1117IDCYRG3 1: GND 2: Vout 3: Vin 1 2 3 KIA7805API/P B C E KIA431-AT/P...
Page 77: Exploded Views
EXPLODED VIEWS Cabinet SHINWHA TAPE SGT-730 (BLACK) Details for L551 V501-2 and surrounding parts SHINWHA TAPE SGT-730 V501-1 (WHITE) L551 Scotch CLN551 DVD Mechanical Parts Tape #880 L3-1 CRT CBA L3-2 Scotch TL1-1 Tape #880 TL1-1 DVD Main TB11 CBA Unit DG601 TL1-3 TL1-3...
Page 78 Packing Packing Tape Tape 1-17-2 P7754PEX...
Page 79: Mechanical Parts List
Ref. No. Description Part No. FRONT CABINET ASSEMBLY P7754UT 1EM121836 A1-1 FRONT CABINET T1202UC 1EM121335 A1-2 CONTROL PLATE P7754UT 1EM221549 A1-3 BADGE BRAND T7310UL ~MAGNAVOX~ 0EM407275 A1-4 CASSETTE DOOR T1202UC 1EM422886 A1-5 SPRING DOOR T1200UA 1EM422903 A1-6 CLOTH(4X7XT0.7) T5000UA 0EM404974 A1-7...
Page 80: Electrical Parts List
ELECTRICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C1124 ELECTROLYTIC CAP . 47µF/16V M CE1CMASDL470 Before replacing any of these components, read C1127 ELECTROLYTIC CAP . 1000µF/6.3V M CE0KMASDL102 carefully the product safety notice in this service C1128...
Page 81 Ref. No. Description Part No. Ref. No. Description Part No. C1441 CHIP CERAMIC CAP .(1608) F Z 0.1µF/50V CHD1JZ30F104 C1784 CHIP CERAMIC CAP .(1608) F Z 0.1µF/50V CHD1JZ30F104 C1442 CHIP CERAMIC CAP .(1608) F Z 0.1µF/25V CHD1EZ30F104 C1786 ELECTROLYTIC CAP . 4.7µF/50V M H7 CE1JMAVSL4R7 C1443 CHIP CERAMIC CAP .(1608) F Z 0.1µF/25V...
Page 82 Ref. No. Description Part No. Ref. No. Description Part No. D1216 LED LAMP 333GT/F45-50 NPWZ3GTF4550 IC1601# PHOTOCOUPLER LTV-817C-F NPEC0LTV817F D1217 LED LTL-4214M1 NPQZLTL4214M IC1682# IC VOLTAGE REGULATOR 5V KIA7805API/P NSZBA0SJY041 D1224 LED SIR-563ST3F P QPQPS1R563ST IC1701 IC HIFI LA72670BM-MPB-E QSZBA0RSY039 D1229# ZENER DIODE MTZJT-7715B QDTB00MTZJ15...
Page 83 Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES. 1/10W F 150 Ω Q1905# FET 2SK3757(Q) QFWZ02SK3757 R1172 RRXAFR5H1500 CHIP RES. 1/10W F 4.7k Ω Q1906 NPN TRANSISTOR KRC103M-AT/P NQSZKRC103MP R1173 RRXAFR5H4701 CARBON RES. 1/4W J 390 Ω Q1907# TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P...
Page 84 Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES.(1608) 1/10W 0 Ω CARBON RES. 1/4W J 1.2k Ω R1257 RRXAJR5Z0000 R1610 RCX4JATZ0122 CHIP RES.(1608) 1/10W 0 Ω CARBON RES. 1/4W J 150 Ω R1258 RRXAJR5Z0000 R1613 RCX4JATZ0151 CARBON RES.
Page 85 Ref. No. Description Part No. Ref. No. Description Part No. CARBON RES. 1/4W J 180 Ω R1802# RCX4JATZ0181 SW1208 TACT SWITCH SKQSAB SST0101AL038 METAL OXIDE FILM RES. 1W J 18 Ω R1803# RN01180ZU001 SW1209 TACT SWITCH SKQSAB SST0101AL038 CHIP RES. 1/10W J 2.2k Ω R1804 RRXAJR5Z0222 SW1210...
Page 86 SUB CBA Ref. No. Description Part No. DIODES Ref. No. Description Part No. D2300 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 SUB CBA (MPS-A) ---------- Consists of the following: D2301 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 CAPACITORS D2302 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 D2304 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133 C2305 ELECTROLYTIC CAP .
Page 87 Ref. No. Description Part No. Ref. No. Description Part No. CARBON RES. 1/4W J 470 Ω CARBON RES. 1/4W J 5.6 Ω R2321 RCX4JATZ0471 R2649# RCX4JATZ05R6 CARBON RES. 1/4W J 33 Ω CARBON RES. 1/4W J 1.2 Ω R2322 RCX4JATZ0330 R2650 RCX4JATZ01R2 CHIP RES.
Page 88 JUNCTION-A CBA Ref. No. Description Part No. D2505 PCB JUMPER D0.6-P5.0 JW5.0T Ref. No. Description Part No. COIL JUNCTION-A CBA ---------- L2501 INDUCTOR 180µH-J-5FT LLARJCSTU181 Consists of the following: TRANSISTORS CONNECTOR Q2501# NPN TRANSISTOR 2SC2482(T6FUNAIF M QRSZ2SC2482F CN3802 242 SERIES CONNECTOR TUC-P04X-B1 WHT JCTUB04TG002 Q2502# NPN TRANSISTOR 2SC2482(T6FUNAIF M...
Page 89 Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law. CT202MW8 P7754UT 2007-02-06...

Magnavox CT202MW8 Service Manual

Quick Links

SERVICE MANUAL

Related Manuals for Magnavox CT202MW8

Summary of Contents for Magnavox CT202MW8

Table of Contents