Learning Function; Erasing A Key Code - Bauhn UR39677 Instructional Manual

Learning Function

For the learning function you must have the
original remote control unit of the device you want
to program, and this remote control unit must be
working properly.
The learning function lets you have the original remote control
unit teach the different button functions to your new universal
remote control. This lets you add or edit any specific buttons
that do not work properly when using a preset device code or
control a device whose device code is not available.
Learning a Key Code Signal
Place the original remote control unit of the device with its
transmitter side (front) facing towards the universal remote
control (see diagram). The optimum distance is between 0.5
and 2 inches (0.5cm to 5cm).
In very rare cases, the specified distance is too
large. If the programming cannot be completed
successfully, reduce the distance between the two
remote controls and try it again.
1. Press the source device selection button (2) of the device
you want to program.
2. Press and hold the SET button (21) for at least 3 seconds.
The display shows [CODE SETUP]. Then release the SET
button (21).
3. Press (8) twice. The display shows [LEARNING].
4. Press the OK button (22). The display shows [LEARN
KEY].
5. Press the OK button (22) again. The display shows
[SELECT KEY].
6. Press the button that you want to assign on the universal
remote control. The display shows [WAITING].
7. Press and hold down the button on the original remote
control which you want to copy the signal from for at
least 3 seconds. After releasing the button, the message
[SUCCESS] or [FAIL] appears on the display.
8. If you see the message [SUCCESS], the command has
been programmed successfully.
9. If necessary, you may repeat the last two steps to copy
another command and assign it to a different button.
13
After Sales Support
Telephone: 1300 663 907
Internet: www.winplus.com.au
10. If you see the message [FAIL], the command could not be
programmed. Repeat these steps with the same button,
but keep it pressed longer.
11. After all the desired buttons have been programmed, quit
the programming mode by pressing the EXIT button (23).
It is not possible to exit programming while the
universal remote control is still waiting for a
command to be sent from the original remote
control (the display shows [WAITING]).
12. Quit the programming mode by pressing the EXIT button
(23) three times.

Erasing a Key Code

You may erase a learned key code without altering any of the
other programmed functions.
1. Press the source device selection button (2) of the device
for which you want to edit the programmed information.
2. Press and hold the SET button (21) for at least 3 seconds.
The display shows [CODE SETUP]. Then release the
SET button (21).
3. Press (8) twice. The display shows [LEARNING].
4. Press the OK button (22). The display shows [LEARN KEY].
5. Press (8). The display shows [DELETE KEY].
6. Press the OK button (22). The display shows
[SELECT KEY].
7. Press the button whose function you want to erase.
The message [SURE DELET] will appear on the display.
8. Press the OK button (22) to confirm the deletion.
9. The message [DELETED] will appear for a few seconds
and the device returns to the previous menu
[SELECT KEY].
10. If required, continue erasing more key functions by
pressing the corresponding button, or quit the deletion
process by pressing any source device selection
button (2).
Erasing All Key Codes for a Device
This function allows you to erase all manually learned key
commands for a specific device. Any buttons that have been
programmed via a device code will not be erased.
1. Press the source device selection button (2) of the device
for which you want to erase all programmed information.
2. Press and hold the SET button (21) for at least 3 seconds.
The display shows [CODE SETUP]. Then release the
SET button (21).
3. Press (8) twice. The display shows [LEARNING].
4. Press the OK button (22). The display shows [LEARN KEY].
After Sales Support
Telephone: 1300 663 907
Internet: www.winplus.com.au
14