Advertisement
Quick Links
ARCH™
SINGLE CONTROL
KITCHEN PULL-OUT FAUCET
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
RECOMMENDED
TOOLS
1
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
Installation with ESCUTCHEON: Figure A.
mounting surface is uneven. Insert SEAL (1) into groove at base of faucet. Insert supply HOSES (2) and SHANK (3)
through ESCUTCHEON (4) and mounting surface.
Assemble RUBBER WASHER (5), BRASS WASHER (6) and threaded LOCKNUT (7) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (7) and check that rotation of HANDLE (8) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (9) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening the screws
slightly each time until all are snug to ensure even pressure.
Installation for single hole mounting: Figure B.
SEAL (1) into groove at base of faucet. Insert supply HOSES (2) and SHANK (3) through ESCUTCHEON (11) and mounting surface.
Assemble RUBBER WASHER (5), BRASS WASHER (6) and threaded LOCKNUT (7) onto SHANK (3) from underside of
sink or mounting surface. Hand tighten LOCKNUT (7) and check that rotation of HANDLE (8) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (9) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening the screws
slightly each time until all are snug to ensure even pressure.
8
Figure A
1
2
4
S I N K O R
M O U N T I N G
S U R FA C E
5
9
Adjustable Wrench
Apply a light bead of plumbers putty to underside of ESCUTCHEON (1) if
7
G R O O V E I N FA U C E T
3
6
7
Installation
Instructions
4101.100
4101.100F15
Regular Screwdriver
CAUTION
Insert SEAL (10) into groove at base of ESCUTCHEON (11). Insert
Figure B
S I N K O R
M O U N T I N G
S U R FA C E
Certified to comply with ANSI A112.18.1M
Phillips Screwdriver
Channel Locks
Turn off water at
main supply.
8
7
1
G R O O V E I N FA U C E T
11
10
G R O O V E I N E S C U T C H E O N
3
2
5
6
7
9
M 9 6 8 5 8 6 R ev. 1. 5
Advertisement
Related Manuals for American Standard ARCH 4101.100
Summary of Contents for American Standard ARCH 4101.100
- Page 1 Installation Instructions ARCH™ 4101.100 4101.100F15 SINGLE CONTROL KITCHEN PULL-OUT FAUCET Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1M M 9 6 8 5 8 6 R ev.
- Page 2 MAKE WATER SUPPLY CONNECTIONS Turn off hot and cold water supplies before beginning. Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect left supply (Marked with a Red Stripe) to Hot and right supply (Marked with Blue Stripe) to Cold wall supply.
- Page 3 TEST INSTALLED FAUCET Move HANDLE (1) down into "off" position. Turn on water supplies. Check connections for leaks. With HANDLE (1) down in "off" position, pull HAND SPRAY (2) from FAUCET (3). SPRAY (HOSE (5) should pull approximately 2 feet and direct open SPRAY END (2) into sink.
- Page 4 ARCH™ SINGLE CONTROL KITCHEN PULL-OUT FAUCET MODEL NUMBERS 4101.100 4101.100F15 M962717-YYY0A M962716-0070A HANDLE KIT B U T T O N A N D S C R E W K I T M907302-YYY0A ESCUTCHEON CAP M918506-0070A CARTRIDGE SCREWS A951470-0070A CARTRIDGE M953173-YYY220A (2.2 GPM) SPRAY M953173-YYY150A M911261-0070A...