Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for SANLI BSB 33
Summary of Contents for SANLI BSB 33
- Page 1 BSB 33 Back-Pack Leaf Blower PLEASE KEEP THIS MANUAL IN A SAFE PLACE...
-
Page 2: Table Of Contents
Contents 1. Guide to using this manual………………………………………..1 2. Safety precautions………………………………………………… .2 3. Maintenance and repair…………………………………………..6 4.Technical specifications…………………………………….…….…7 5. Parts list.…………………………………………………...….…..8 6. Assembling the unit……….………………………………..……..8 7. Fueling……………………………………………………..….…..9 8. Starting/Stopping…………………………………………….….…11 9. Operating instructions………………………………………….….13 10. After finishing work…………………………………………..….13 11.Storing the machine…………………………………………...…..15 12.Part pictures and lists……………………………………………..17 13.CE conformity……………………………………………………21 14.Notes……………………………………………………………...22 15.Warranty Card…………………………………………………….28... -
Page 3: Guide To Using This Manual
Guide to using this manual Graphic illustration All the important parts of this machine are shown and explained in this manual. The operating and handling instructions are supported by graphic illustration. Symbols in text The individual steps or procedures described in the manual may be marked in different ways. -
Page 4: Safety Precautions
Technology improvements Our management principle is to improve the quality continually. As a result, our technology is improved from time to time. If the operating characteristics or the appearance of your machine differ from those described in this manual, please contact your dealer for assistance. Therefore, we cannot be responsible for changes, modifications or improvements that are not covered in this manual. - Page 5 model are authorized. -Other accessories must not be used because of the increased risk of accidents. -The company excludes all liability for personal injury and damage to property caused while using unauthorized accessories. Wear proper clothing and equipment Clothing must be sturdy and snug-fitting, but allow complete freedom of movement—...
- Page 6 Remove the fuel filler cap on the unit carefully so as to allow any pressure build-up in the tank to release slowly. Fuel your blower in well-ventilated areas, outdoors only. Wipe off any spilled fuel before starting and check for leakage. Take care not to get fuel on your clothing.
- Page 7 only. ·To reduce the risk of breathing toxic fumes, never start or run your unit in confined spaces. ·Place the unit on firm ground in an open area. ·Make sure you have good balance and secure footing. ·Hold the unit securely. Your blower is a one-person unit.
-
Page 8: Maintenance And Repair
or stumble. Warning: when spraying To reduce the risk of inhaling poisonous fumes from chemicals and exhaust gases, do not operate the blower in confined spaces. Walk forward only when the unit is running.. In an emergency, release the quick-action buckles, slip out of the harness and throw off the machine. -
Page 9: Technical Specifications
machine.(Exception: carburetor and idle adjustments.) Always clean dust and dirt off the machine after finishing work. Do not store or service your unit near any fire or flame ----Check fuel cap regularly for leak ----Use only the approved spark plug (see specifications) and make sure it is in good condition ----Inspect ignition wires (insulation in good condition, secure connect) -
Page 10: Parts List
Parts List 1、 Main unit 2、 Blower pipe A 3、 Blower pipe B 4、 Blower pipe C 5、 Blower pipe D 6、 Control Box 7、 Hose 8、 (40：1)Oil Can 9、 Clip Assembling the unit Adjusting the control handle ·Put the unit on your back ·Release the clamp screw ·... -
Page 11: Fueling
Loosening the harness straps ·Lift the tabs of the two sliding adjusters · Adjust the straps so that the back plate is held firmly and comfortably against your back. Adjuster Fueling Your engine requires a mixture of gasoline and engine oil. The quality of these constituents and the mixed ratio has a decisive influence on the function and service life of the engine. - Page 12 Poor quality gasoline or engine oil may damage the engine, sealing rings, hoses and the fuel tank. Mixing fuel Avoid direct skin contact with gasoline and avoid inhaling gasoline vapor. Use a container approved for storing fuel. Pour oil into the container first, then add gasoline , and mix thoroughly.
-
Page 13: Starting/Stopping
Starting/ stopping the engine ·Observe safety precautions—see chapter (Safety precautions) ·Move the lever to the center position—This is the oil-controlling setting. Notes: · The lever can adjust the airflow volume. · Put the lever on “0” before switching off the engine, and the engine will stop automatically. - Page 14 housing and put one foot against the base plate to prevent it slipping. ·Pull the starter grip slowly with your right hand to 20cm and give it a brisk strong pull. ·Do not pull the starter rope out all the way as it might otherwise break. ·Do not let the starter grip snap back.
-
Page 15: Operating Instructions
·Pull the starter rope at least 10 times Operation instructions During break-in A new machine should not be running at high speed. This avoids unnecessary high loads during the break-in period. As all moving parts have to e fitted during the break-in period. The frictional resistances in the engine are greater during this period. - Page 16 Carburetor General information: Your carburetor comes from the factory with a standard setting. This setting provides an optimum fuel-air mixture under most operating conditions. The high speed screw alters the engine power output and the maximum off-road engine speed. If the setting is too lean, there is a risk of engine damage due to insufficient lubrication and overheating.
-
Page 17: Storing The Machine
Engine running behavior If engine running behavior is unsatisfactory even though the air filter is clean and the carburetor properly adjusted, the cause may be in the muffler. Have the muffler checked for contamination by dealer. Storing the machine For periods of about 3 months or longer ·Clean the fuel tank ·... - Page 18 Maintenance and repair All the operations described in the Maintenance chart must be performed on a regular basis. If these maintenance operations can not be performed by the owner, they should be performed by an authorized dealer. If these operations are not carried out as specified, the user assumes responsibility for any damage that may occur.
- Page 20 BSB33 BACKPACK LEAF BLOWER EXPLOSIVE PART LIST Qty. Qty. Qty. Ser.No. Erp No. Part Name Ser.No. Erp No. Part Name Ser.No. Erp No. Part Name 4305 M6 Nut 2-22 4479 Lock nut M6 GB6177 2-43 0954 Throttle lever 3015 Washer 6 2-23 6425 Shield...
- Page 22 BSB33 GASOLINE ENGINE Item No. Part No. Part Name Qty. Item No. Part No. Part Name Qty. Item No. Part No. Part Name Qty. 8817 Valve,fuel cap 0554 Fuel filter comp 1273 Stopper 8574 Holder,valve 3365 Woodruff key 2890 Gasket,insulator 5689 Rotor 3826...
-
Page 23: Ce Conformity
EC DECLARATION OF CONFORMITY Fujian Jinjiang Sanli Engine Co., Ltd. Declares that the following equipment manufactured by Fujian Jinjiang Sanli Engine Co., Ltd conforms to the following Directive(s):2000/14/EC,2006/42/EC,2004/108/EC and 97/68/EC of the European Parliament and of the council on the approximation of the laws of the Member States relating to the noise emission in the environment by equipment for use outdoors. -
Page 24: Notes
Notes... - Page 25 BSB 33...
-
Page 26: Warranty Card
WARRANTY CARD REGISTER YOUR MACHINE TO VALIDATE YOUR WARRANTY. To validate your warranty, register your equipment with SANLI after its purchase by returning the warranty card provided at the back of the user's manual or on the website www.sanli.co.uk/register,www.sanli.fr,www.sanli.com.au Reference...
Need help?
Do you have a question about the BSB 33 and is the answer not in the manual?
Questions and answers