zBoost DataBlast VLTE-AWS Setup Overview

PACKAGE CONTENTS
zBoost Base Unit with
Silver Mounting Bracket
Coax Cable
RG-59(mini), 50 ft
Signal Antenna
(2 pieces) and
Power Supply Base Unit Antenna
Mounting Hardware
SETTING UP YOUR zBOOST SIGNAL BOOSTER
®
The zBoost DataBlast YX550 is designed to provide increased in-building data
coverage, up to 2500 square feet, making it perfect for the home and office. The
zBoost DataBlast supports multiple users and all devices operating on the
Network(s) covered by your model.
• VLTE-AWS: Verizon LTE and AWS
• ALTE-AWS: AT&T LTE and AWS
Before installing, please note the following important factors in determining your zBoost
performance:
• At least 15 vertical feet is needed between the Signal Antenna (receives the
outside signal) and the Base Antenna (rebroadcasts the signal indoors). Separation
less than 15 vertical feet will result in decreased performance.
• Keep the Signal Antenna at least 3 feet above any metal.
Boost data transmission in 4 easy steps:
FIRST: Mount the Signal Antenna. Choose a location for the Signal Antenna
using your cell phone to determine the area of strongest signal. The coverage
your zBoost provides is largely determined by the quality of signal received by the
Signal Antenna.
To maximize signal coverage, place the Signal Antenna where you find the strongest
signal (up high or outside) and at least 3 feet above any metal.
IMPORTANT: Incorrectly mounting the Signal Antenna to the mounting bracket (see
figure A) will impede performance. Ensure that the Signal Antenna is properly
positioned in the mounting bracket as pictured.
To mount antenna to a pole: Attach bottom of antenna to pole bracket as
pictured. Use U-Bolt to secure bracket to pole and fasten.
To mount antenna to a flat surface: Attach bottom of antenna to pole bracket
as pictured. Secure bracket to desired surface using provided screws. Use of
the Saddle and U-Bolt are not necessary for this option.
SETUP OVERVIEW
Download the DataBlast YX550 User Guide at www.Wi-Ex.com
SECOND: Place the DataBlast Base Unit where you want to create a Data
Zone TM . Assemble the Base Unit and Base Unit Antenna and position the antenna
vertically. This Base Unit uses an omni-directional antenna that delivers signal in a
circular pattern around the antenna. Place the Base Unit in desired location – where
you want to create a Cell Zone™ For the widest possible signal area, it is
recommended that you position the Base Unit near the middle of a room. The Base
User Guide available
Unit can be placed on a flat surface (e.g., a bookshelf, desk, end table, etc.) and
at www.Wi-Ex.com
performs best when located at least 4 feet above the floor or approximately the
height of a cell phone when it is typically in use (avoid placing the Base Unit on the
floor).
SETUP OVERVIEW
Keep the Base Unit at least 2 feet away from other cords, metal objects or other
wireless devices such as wireless routers or wireless access points. The zBoost
Setup Overview
DataBlast performs best when there are no obstructions between the zBoost Base
Unit and your mobile device.
Note: To mount it on an interior wall, first remove the silver bracket from the Base
Unit, mount the bracket to a wall with 2 screws (not provided), then placing the Base
Unit back into the bracket keeping the antenna vertical.
The zBoost DataBlast requires at least 15 feet of vertical separation between the
Base Unit and the Signal Antenna. Generally, increasing this distance (up to 40 feet)
will increase the performance and decreasing the distance will limit zBoost
performance.
THIRD: Run the provided coaxial cable between the Base Unit and Signal
Antenna. Use the provided 50 feet of RG-59(mini) coaxial cable to connect the
Signal Antenna and the Base Unit. Should you need additional cable length, 15 foot
extensions (Part #: YX030-15w) are available at www.Wi-Exstore.com. Please note:
Figure A Figure A
Pole Bracket
Saddle
U-Bolt
Signal Antenna
Cell Tower
Coaxial Cable
Base Antenna Base Antenna
Power Supply
DataB DataBlast Base Unit
* *Note: An 8 inch window entry cable may be needed for this option. It is available for purchase at www.Wi-Ex.com (Part #: YX030-08W)
zBoost
DataBlast
YX550
Cable longer than 65 feet is not recommended.
FOURTH: Connect the Base Unit to the provided power supply and plug into a
power outlet. When the system is in place and fully connected, walk throughout your
home or office and verify that you have fast, reliable data speeds. If the signal
strength has improved, your zBoost DataBlast is working. Remember, coverage
varies based on outdoor signal level, building construction, and antenna placement.
Coverage in adjoining rooms will be reduced by walls and building materials.
Upon initial power up, a solid GREEN LED should appear indicating normal
conditions. If a RED light appears, adjustments may be needed to optimize
performance. If you find the increased signal coverage is acceptable, however, no
additional adjustments are needed. See LED Indicator section for more information.
Should you desire to improve coverage, you may:
• Relocate the Signal Antenna in order to capture a better signal–higher is better.
• Increase the distance between the Base Unit and the Signal Antenna.
• Purchase an upgrade antenna available at www.Wi-Ex.com.
BASE UNIT LED INDICATORS
At Initial Power Up Only
Normal condition at power up.
Solid GREEN
zBoost is working, but at reduced performance and coverage due to
Slowly Alternating
"non-ideal" setup. Increase the distance between antenna and
RED and GREEN
amplifier to achieve maximum performance and coverage.
Indicates insufficient distance between the antenna and the amplifier.
Fast Flashing RED
The amplifier is operating at significantly reduced coverage.
System is receiving signals from either the mobile device or the base
Solid RED
station transceiver which are too strong for proper operation.
Fast Alternating The amplifier is disabled.
RED and GREEN
followed by no light
After Initial Power Up
Normal condition
Solid GREEN
Solid RED System is receiving signals from either the mobile device or the base
station transceiver which are too strong for proper operation.
Unplug your system and re-orient the Signal Antenna and/or Base
Unit to reduce excessive signal. If LED remains RED after
reconnecting power, contact customer support at 1-800-871-1612.
®
Models:
• VLTE-AWS
TM
• ALTE-AWS
Rev C