Do you have a question about the T701 and is the answer not in the manual?
Questions and answers
Vernie Roberts-Webbe
May 19, 2025
If after replacing the battery, the system does not operate automatically, what actions should be taken
1 comments:
Mr. Anderson
May 23, 2025
If the Pro1 T701 system does not operate automatically after replacing the battery, ensure the thermostat is properly reattached to the backplate. Check that the AA batteries are installed correctly and are new. Also, verify that the system and fan switches are set to the desired modes (HEAT, COOL, or AUTO). If the battery icon still appears or the system remains inoperable, recheck connections or replace the batteries again.
This answer is automatically generated
john myslenski
February 25, 2025
LO on main screen where room temperture would be displayed
1 comments:
Mr. Anderson
May 14, 2025
"LO" on the main screen of the Pro1 T701 thermostat means the current room temperature is lower than the thermostat's measuring range.
This answer is automatically generated
Stephanie Whitbeck
February 16, 2025
How do I get the batteries out to change them?????
1 comments:
Mr. Anderson
February 16, 2025
To change the batteries in the Pro1 IAQ T701 thermostat, follow these steps:
1. Locate the battery door on the thermostat. 2. Open the battery door to access the battery compartment. 3. Remove the old AA batteries. 4. Insert two new AA alkaline batteries, ensuring correct polarity. 5. Close the battery door.
Replace the batteries immediately when the battery icon appears to avoid system inoperability.
This answer is automatically generated
Donna
January 24, 2025
Temp at use does change when heat is switched on when temp was set to be 78 it stays at 70
1 comments:
Mr. Anderson
February 10, 2025
The Pro1 IAQ T701 thermostat may display a temperature of 70 instead of 78 after the heat is switched on because the display shows the current room temperature, not the setpoint temperature. When the heat is turned on, the thermostat will gradually warm the room until it reaches the set temperature of 78. The display will update as the room temperature increases.
This answer is automatically generated
Donna Diboll
January 24, 2025
What causes the temp nature not to change when heat is switched on
1 comments:
Mr. Anderson
February 10, 2025
The temperature setting may not change on the Pro1 IAQ T701 when the heat is switched on if the batteries are low. If the battery icon appears, replace the AA batteries immediately, as failure to do so may result in the heating and cooling system becoming inoperable.
This answer is automatically generated
Sara Springer
January 18, 2025
What causes the "Cool ON" icon to comes on and flash steadily and the system turns off?
1 comments:
Mr. Anderson
February 4, 2025
The "Cool ON" icon flashes steadily, and the system turns off on a Pro1 IAQ T701 thermostat due to a compressor delay feature. This is a normal function to protect the system from damage, and the delay will last for approximately 5 minutes.
This answer is automatically generated
Alan Jacobson
June 13, 2025
Using AC function. Temperature is set at 75 degrees. It will activate at 76 degrees but it will not shut off until 74 degrees. It runs an extra 45 minutes after it reaches th e set temperature and only shuts off when it reaches one degree lower than the setting. Can I set it to shut off when it reaches room temperature setting.
THERMOSTAT QUICK REFERENCE Getting to know your thermostat Displays the user selectable setpoint temperature. System operation indicators: The COOL, HEAT or FAN icon will display when the COOL, HEAT or FAN is on. NOTE: The compressor delay feature is active if these icons are flashing.
Page 3
THERMOSTAT OPERATION Easy to use controls Caution: When the battery icon appears replace your AA batteries immediately. Failure to do so may result in your heating & cooling system becoming inoperable. Fan Switch: Select ON or AUTO. ON will run the fan continuously.
60 days of installation. You can register your new thermostat in 2 ways. Go to www.pro1iaq.com, select warranty registration and fill out a short registration form. - or - Complete the form below and mail it to the address shown. Pro1 IAQ Warranty Registration: Name: ____________________________ Thermostat Model:...
Need help?
Do you have a question about the T701 and is the answer not in the manual?
Questions and answers
If after replacing the battery, the system does not operate automatically, what actions should be taken
If the Pro1 T701 system does not operate automatically after replacing the battery, ensure the thermostat is properly reattached to the backplate. Check that the AA batteries are installed correctly and are new. Also, verify that the system and fan switches are set to the desired modes (HEAT, COOL, or AUTO). If the battery icon still appears or the system remains inoperable, recheck connections or replace the batteries again.
This answer is automatically generated
LO on main screen where room temperture would be displayed
"LO" on the main screen of the Pro1 T701 thermostat means the current room temperature is lower than the thermostat's measuring range.
This answer is automatically generated
How do I get the batteries out to change them?????
To change the batteries in the Pro1 IAQ T701 thermostat, follow these steps:
1. Locate the battery door on the thermostat.
2. Open the battery door to access the battery compartment.
3. Remove the old AA batteries.
4. Insert two new AA alkaline batteries, ensuring correct polarity.
5. Close the battery door.
Replace the batteries immediately when the battery icon appears to avoid system inoperability.
This answer is automatically generated
Temp at use does change when heat is switched on when temp was set to be 78 it stays at 70
The Pro1 IAQ T701 thermostat may display a temperature of 70 instead of 78 after the heat is switched on because the display shows the current room temperature, not the setpoint temperature. When the heat is turned on, the thermostat will gradually warm the room until it reaches the set temperature of 78. The display will update as the room temperature increases.
This answer is automatically generated
What causes the temp nature not to change when heat is switched on
The temperature setting may not change on the Pro1 IAQ T701 when the heat is switched on if the batteries are low. If the battery icon appears, replace the AA batteries immediately, as failure to do so may result in the heating and cooling system becoming inoperable.
This answer is automatically generated
What causes the "Cool ON" icon to comes on and flash steadily and the system turns off?
The "Cool ON" icon flashes steadily, and the system turns off on a Pro1 IAQ T701 thermostat due to a compressor delay feature. This is a normal function to protect the system from damage, and the delay will last for approximately 5 minutes.
This answer is automatically generated
Using AC function. Temperature is set at 75 degrees. It will activate at 76 degrees but it will not shut off until 74 degrees. It runs an extra 45 minutes after it reaches th e set temperature and only shuts off when it reaches one degree lower than the setting. Can I set it to shut off when it reaches room temperature setting.