Pioneer DEH-8450BT Owner's Manual page 14

Section
Operating this unit
02
3 Turn M.C. to select the initial setting.
After selecting, perform the following proce-
dures to set the initial setting.
Language select (multi-language)
For your convenience, this unit equips multiple
language display. You can select the language
best suited to your first language.
1 Press M.C. to select the language.
English—Español—Português
Calendar (setting the date)
1 Press M.C. to select the segment of the calen-
dar display you wish to set.
Year—Day—Month
2 Turn M.C. to set the date.
Clock (setting the clock)
1 Press M.C. to select the segment of the clock
display you wish to set.
Hour—Minute
2 Turn M.C. to adjust the clock.
EngineTime alert (elapsed time display setting)
This setting allows you to measure the length of
time that elapses from when the machine is
turned on and display the amount of elapsed time
per set period.
Also, you will hear alarm.
1 Press M.C. to select your favorite setting.
OFF—15Minutes—30Minutes
FM step (FM tuning step)
The FM tuning step employed by seek tuning can
be switched between 100 kHz, the preset step,
and 50 kHz.
If seek tuning is performed in 50 kHz steps, sta-
tions may be tuned in imprecisely. Tune in the sta-
tions with manual tuning or use seek tuning
again.
1 Press M.C. to select the FM tuning step.
50kHz (50 kHz)—100kHz (100 kHz)
14
En
AM step (AM tuning step)
The AM tuning step can be switched between
9 kHz, the preset step, and 10 kHz. When using the
tuner in North, Central or South America, reset
the tuning step from 9 kHz (531 kHz to 1 602 kHz al-
lowable) to 10 kHz (530 kHz to 1 640 kHz allowable).
1 Press M.C. to select the AM tuning step.
9kHz (9 kHz)—10kHz (10 kHz)
Auto PI (auto PI seek)
The unit can automatically search for a different
station with the same programming, even during
preset recall.
1 Press M.C. to turn Auto PI seek on or off.
Music browse (music browse)
When operating external storage devices (USB,
SD), you can select files from the list.
1 Press M.C. to select the setting.
OFF—USB memory1—USB memory2—SD
card
Warning tone (warning tone setting)
If the front panel is not detached from the head
unit within four seconds of turning off the ignition,
a warning tone sounds. You can turn off the warn-
ing tone.
1 Press M.C. to turn the warning tone on or off.
AUX (auxiliary input)
Activate this setting when using an auxiliary de-
vice connected to this unit.
1 Press M.C. to turn auxiliary setting on or off.
Dimmer (dimmer setting)
To prevent the display from being too bright at
night, the display is automatically dimmed when
the car's headlights are turned on. You can turn
the dimmer on or off.
1 Press M.C. to turn dimmer on or off.
Contrast (display contrast setting)
Operating this unit
1 Turn M.C. to adjust the contrast level.
0 to 15 is displayed as the level is increased or
decreased.
S/W control (rear output and subwoofer setting)
This unit's rear output (rear speaker leads output
and RCA rear output) can be used for full-range
speaker (Rear SP :F.Range) or subwoofer (Rear
SP :S/W) connection. If you switch the rear output
setting to Rear SP :S/W, you can connect a rear
speaker lead directly to a subwoofer without using
an auxiliary amp.
1 Press M.C. to switch the rear output setting.
! When no subwoofer is connected to the
rear output, select Rear SP :F.Range (full-
range speaker).
! When a subwoofer is connected to the rear
output, select Rear SP :S/W (subwoofer).
! Even if you change this setting, there will be
no output unless you turn the subwoofer out-
put on (refer to Subwoofer1 (subwoofer on/off
setting) on page 11).
! If you change this setting, subwoofer output in
the audio menu will return to the factory set-
tings.
! Both rear speaker lead outputs and RCA rear
output are switched simultaneously in this set-
ting.
Demonstration (demo display setting)
1 Press M.C. to turn the demo display on or off.
Ever-scroll (scroll mode setting)
When ever scroll is set to ON, recorded text infor-
mation scrolls continuously in the display. Set to
OFF if you prefer the information to scroll just
once.
1 Press M.C. to turn the ever scroll on or off.
BT AUDIO (Bluetooth audio activation)
! This function is not available for DEH-7450SD.
You need to activate the BT Audio source in order
to use a Bluetooth audio player.
1 Press M.C. to turn the BT Audio source on or
off.
Clear memory (resetting the Bluetooth wireless
technology module)
! This function is not available for DEH-7450SD.
Bluetooth device data can be deleted. To protect
personal information, we recommend deleting
this data before transferring the unit to other per-
sons. The following settings will be deleted.
! phone book entries on the Bluetooth tele-
phone
! preset numbers on the Bluetooth telephone
! registration assignment of the Bluetooth tele-
phone
! call history of the Bluetooth telephone
! information of the connected Bluetooth tele-
phone
! PIN code of the Bluetooth device
1 Press M.C. to show the confirmation display.
YES is displayed. Clearing memory is now on
standby.
If you do not want to reset phone memory, turn
M.C. to display CANCEL and press to select.
2 Press M.C. to clear the memory.
Cleared is displayed and the settings are de-
leted.
! While this function is in use, do not turn
off the engine.
BT Version info. (Bluetooth version display)
! This function is not available for DEH-7450SD.
You can display the system versions of this unit
and of Bluetooth module.
1 Press M.C. to display the information.
! Turning M.C. or LEVER cycles between the
system version of this unit and that of the
Bluetooth module.