Advertisement
6. Set the heat setting between
HEAT and HIGH HEAT with the
button
.
7. All settings for the first program are done now. Enter a new program
according to the steps 1-6 or activate the already entered program by
leaving this menu with the
8. Now the program mode is active, the symbol PROG appears. The
heater operates according to the entered information. While the program
mode is activated, the start and stop time, the active program number
and the desired and actual ambient temperature
alternating.
9. An entered program can be checked, edited and deleted just by
navigating again into the PROG menu and pressing the enter button. With
the
buttons the different program numbers can be selected. To
delete one program number, press the
program) appears and by pressing the enter button
program will be deleted.
program.
Time setting (TIME) - see Fig. 11
Navigate the cursor to TIME with the
button
to adjust the weekday with the
enter button
and set the hours and minutes with
or
to leave the time menu.
Frost protection - see Fig. 6
Choose a heat setting and set the desired ambient temperature between
5°C and 8°C
(see 'Operation').
When the temperature falls below +5 °C...+8 °C, the appliance switches
on automatically.
Wall mounting - see Fig. 4
The minimum distances must be observed - see Fig. 2 & 3
For installation of the appliance, care must be taken not to damage
concealed cables.
Please be careful when drilling the holes.
The appliance may only be operated when mounted vertically on a wall.
The appliance is not suitable for ceiling mounting.
Transport - see Fig. 5
Overheat cut-out
The built-in overheat cut-out switches off the appliance automatically in
the event of a fault. Disconnect the mains plug from the socket. After a
short cooling down phase, the appliance switches into stand-by mode
and is ready for use again. If the fault should occur again, see your local
dealer.
Glen Dimplex UK Limited
Millbrook House
Grange Drive
Hedge End
Southampton
Hampshire. SO30 2DF
[c] Glen Dimplex UK Limited
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Glen Dimplex UK Limited.
(fan only) / LOW HEAT/ MEDIUM
buttons and confirm with the enter
button.
will be displayed
button. The CP symbol (clear
leaves the menu without deleting the
buttons. Press the enter
buttons. Confirm with the
. Press enter
UK customer help line (8.00AM – 6.00PM Mon-Fri; 8.30AM-1.00PM Sat)
Customer Services:
Republic of Ireland
Cleaning
WARNING : ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE HEATER
Do not use detergents, abrasive cleaning powders or polish of any kind
on the heater.
Wipe with a dry cloth to remove dust and a damp cloth (not wet) to clean
off stains. Be careful not to allow moisture into the heater.
Ensure that dust or fluff does not accumulate inside the heater as this
could lead to overheating of the element. Use a vacuum cleaner to remove
any fluff which does accumulate.
After Sales Service
Your product is guaranteed for three years from the date of purchase.
Within this period, we undertake to repair or exchange this product free
of charge provided it has been installed and operated in accordance
with these instructions.
the current
Your rights under this guarantee are additional to your statutory rights,
which in turn are not affected by this guarantee.
Should you require after sales service you should contact our customer
services help desk on 0870 727 0101. It would assist us if you can
quote the model number, series, date of purchase, and nature of the fault
at the time of your call. The customer services help desk will also be able
to advise you should you need to purchase any spares.
Please do not return a faulty product to us in the first
instance as this may result in loss or damage and delay in providing you
with a satisfactory service.
Please retain your receipt as proof of purchase.
Tel.
Fax.
e-mail
Tel.
0870 7270101
0870 7270102
customer.services@glendimplex.com
01 8424833
Advertisement
