Advertisement
CONSUMPTION DATA
Temperature
Programme
(°C)
Cotton
95
Cotton
60
Cotton with "Eco"**
60
Cotton
40
Synthetics
60
Synthetics
40
Delicates
30
Daily load
40
Quick wash
30
Wool
40
Handwash
40
Handwash
30
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
**
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
Add detergent as indicated on the front page and as
described in the chapter "Detergent and Additives"
in your Instructions for Use.
Close the door and turn the programme selector to the
desired programme and temperature. The indication
lamp next to the "Start/Pause" button
flashes.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the
respective indication lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch
off automatically. Unsuitable combinations of
options are deselected automatically.
"Eco" button
• With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
"Prewash" button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time
by approximately 15 min.
• Do not use liquid detergent for the main wash
when activating the Prewash option.
"Intensive rinse" button
• More water is added and rinse cycle is prolonged.
Load
Water
Energy
Approx. Programme Duration
(kg)
(l)
(kWh)
(hours : minutes)
5.0
49*
1.90
2:00
5.0
44
0.95
2:10
5.0
44
0.85
2:20
5.0
44
0.60
2:00
2.5
50*
0.70
1:30
2.5
45
0.55
1:15
1.5
50
0.50
0:45
3.0
45
0.45
1:00
3.0
40
0.40
0:30
1.0
55
0.60
0:45
1.0
45
0.60
0:40
1.0
45
0.50
0:40
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
"Rinse hold" button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programmes "Synthetics", "Daily load" and
"Delicates".
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
Note: The programme stops to "Rinse hold" at
the time the "Rinse hold" light in the programme
sequence indication is on. The indication lamp
next to the "Start/Pause" button
Terminate the "Rinse hold" option
• Press the "Start/Pause" button
programme will terminate automatically with the
final spin cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the "Drain" programme
and press the "Start/Pause" button
"Variable spin" button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed "0" is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
START DELAY
The "Start Delay"
allows to run the machine at
the consumer's convenience, for example at night
when electricity is cheaper. Do not use liquid
detergent when activating the start delay.
• Select programme, temperature and options.
• Press the "Start delay" button to select the delay
time by 1, 3, 6, 9 or 12 hours.
• Press the "Start/Pause" button
The indication next to the "Start delay" button
flashes and goes off when the programme starts.
• Once having pressed the "Start/Pause" button
, the countdown of the time delay begins.
When the programme starts, the start delay
indicator light goes off and is replaced by the
programme sequence indication.
• After the "Start/Pause" button
pressed, the number of hours preselected can be
reduced by pressing again the "Start delay" button.
To cancel the "Start delay"
..before you press the "Start/Pause" button:
• Turn the programme selector to another
position or press the "Reset" button
..after having pressed the "Start/Pause" button:
• Press the "Reset" button
seconds - the start delay indicator light goes out.
PROGRAMME START
Open the tap and press the "Start/Pause" button
. The indication lamp next to the "Start/Pause"
button
lights up. The programme sequence
flashes.
indicator shows the current programme phase, running
:
from left to right through Wash, Rinse, Spin/Drain.
; the
When the programme phase is finished, the
corresponding indication goes out.
"DOOR OPEN" INDICATION
.
Before starting and after end of a programme, the
lamp lights to show that the door can be opened. As
long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to "Cancel
(Reset) a running programme before the end".
RED INDICATIONS
"Water tap closed"
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the "Troubleshooting Guide" in the
Instructions for Use.
"Clean pump"
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
.
the latter case refer to the Instructions for Use
("Removing the Filter").
"Service"
Lighting up of the "Service" indication can be caused by
a fault in an electrical component. Refer to the
"Troubleshooting Guide" in your Instructions for Use; if
the fault persists, contact our After Sales Service.
PROGRAMME END
has been
• All the lights of the programme sequence
indicator are off, and the "Door open"
indication
lights up.
1. Turn the programme selector to the "Off/O"
position.
2. Close the water tap.
.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
for at least 3
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the "Start/Pause" button
the programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the "Start/Pause" button
new programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
The "Reset" button
before the end.
• Press the "Reset" button
seconds. Any existing water is drained out
before the door can be opened.
Whirlpool is a registered trademark of Whirlpool USA
to pause
again. The
cancels a programme
for at least 3
5019 301 10453
Advertisement
