1. Manuals
  2. Brands
  3. Stollmann Manuals
  4. Adapter
  5. TA+P2I
  6. User manual

Stollmann TA+P2I User Manual

Adapting isdn phones to pots fxs
Hide thumbs Also See for TA+P2I:
Table of Contents

Advertisement

Quick Links

Download this manual
TA+P2I
Adapting ISDN Phones to
POTS FXS
User Manual
Release r06

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TA+P2I and is the answer not in the manual?

Questions and answers

Related Manuals for Stollmann TA+P2I

Summary of Contents for Stollmann TA+P2I

  • Page 1 TA+P2I Adapting ISDN Phones to POTS FXS User Manual Release r06...
  • Page 2 ® The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Stollmann E+V GmbH is under license. Other trademarks and trade names are those of their respective owners. Release r06 www.stollmann.de...

  • Page 3: Table Of Contents

    2.2 Procedure of Installation for ISDN phones ............ 5 2.3 Procedure of Installation for ISDN PABX ............7 2.4 Displays......................8 2.5 Interfaces...................... 9 Usage of the TA+P2I ..................9 3.1 Incoming call....................10 3.2 Outgoing call....................11 3.3 Call waiting ....................11 3.4 Call Hold / Enquiry ..................

  • Page 4: Introduction

    Software version V1.715 or later 1.1 Product description Using the TA+P2I you can connect ISDN phones or an ISDN PABX with two analogue interfaces (POTS FXS). The analogue lines of the TA+P2I react like standard analogue phones und have to be connected with the FXO ports of the switching system or adapter.

  • Page 5: Installation

    TA+P2I User Manual 2 Installation 2.1 Content This package contains the following parts: • TA+P2I adapter • External power supply (cable length approx. 1.85m) • Two cable for the analogue interfaces (cable length approx. 1.00m) • This user manual •...
  • Page 6 The installation of your TA+P2I is done in a few simple steps: • Connect the power supply to the TA+P2I and mains: The green LED “READY” at the front panel will be lit. Attention: Please use only the delivered power supply! •...

  • Page 7: Procedure Of Installation For Isdn Pabx

    To use the TA+P2I with an ISDN PABX please do the steps below: • Connect the power supply to the TA+P2I and mains: The green LED “READY” at the front panel will be lit permanently. Attention: Please use only the delivered power supply! •...

  • Page 8: Displays

    For accepting incoming calls with the correct calling number, you have to set up the MSN inside the ISDN PABX: Set up the MSN of your ISDN PABX as they are signaled by the TA+P2I: By default the MSN “1” for the analogue line 1 and the MSN “2” for the analogue line 2.

  • Page 9: Interfaces

    ! Attention: Please use only the delivered power supply ! 3 Usage of the TA+P2I By adapting with the TA+P2I you can use many supplementary services known from the ISDN also via the analogue lines, the services have to be activated on the analogue lines.

  • Page 10: Incoming Call

    If a phone number according to the call number of the analogue lines shall be used, you have to set up this correct MSN both in the TA+P2I and the ISDN phones. To change the setting for the MSN for analogue line 1 please do the following: •...

  • Page 11: Outgoing Call

    (line 1 or line 2), that will be used for the outgoing call. If no MSN is defined in the ISDN phone, the TA+P2I uses the next free analogue line (line 1 or line 2). If a wrong MSN (a MSN which does not match with any MSN configured in the TA+P2I) is configured in the ISDN phone, an outgoing call is not possible.

  • Page 12: Three Party Conference

    TA+P2I User Manual 3.5 Three party conference You can start a three party conference by the typical sequence as usual for the ISDN phone (menu driven). 3.6 Call forwarding You can activate and deactivate call forwarding by the typical sequence as usual for an analogue line by prefix codes.

  • Page 13: Error Diagnostic

    Is the MSN programmed in the ISDN Check the setting of the MSNs in the phone also programmed in the TA+P2I? ISDN phone and the TA+P2I. In the default configuration of the TA+P2I MSN “1” is configured for analogue line 1 and MSN “2”...

  • Page 14: Error: No Dial Tone

    The TA+P2I supports all ISDN phones and ISDN PABX’s configured to “multipoint” mode. • The TA+P2I does not support data connections via ISDN modems or ISDN PC cards. Voice connections like answering machine and fax G3 are supported. • Call waiting: Due to technical reason another phone in the same phone number group is ringing in case of call waiting.

  • Page 15: Configuration

    00000103ddmmyyhhmm Set-up date and time 00000104yy Set-up year only (dd=day; mm=month; yy=year; hh=hour; mm=minute) 00000980 Reset all parameters to factory default 6 Operation Mode The TA+P2I can only be used in „multipoint“ operation mode. Release r06 www.stollmann.de Page 15 of 18...

  • Page 16: Technical Features

    2 x RJ 45 Terminating resistors Integrated, 2 x 100 Ohm Phantom feeding ISDN-Bus 4 Watt Supplementary services TA+P2I MSN, DDI, call waiting, hold, resume, three party conference, call forwarding Supplementary services transparent using All available on analogue line DTMF...
  • Page 17 TA+P2I User Manual Pin assignment ISDN plug (8 pin; RJ45; ITU I.430/ISO 8877) Signal (S Not connected Not connected [2a] Rx+ (Receive +) [1a] Tx+ (Transmit +) [1b] Tx- (Transmit -) [2b] Rx- (Receive -) Not connected Not connected Release r06 www.stollmann.de...

  • Page 18: History

    TA+P2I User Manual 8 History Version Release Date Change description Nov 2007 First release for firmware version 1.701 Mar 2008 New document structure, Added pin assignment for analogue/ISDN plug Changes for new firmware version 1.715: - Modified behavior depending on the MSN settings during...

Table of Contents