Advertisement
Quick Links
Advertisement
Related Manuals for xenium X-ONE
Summary of Contents for xenium X-ONE
- Page 1 BENUTZERHANDBUCH OWNER’S MANUAL X - ONE CLASS D MONO AMPLIFIER...
-
Page 2: Table Of Contents
TABLE OF CONTENT SAFETY INSTRUCTIONS INSTALLATION INSTRUCTIONS X-ONE Features and operational controls Interconnection example Low Pass-Mode (standard subwoofer operation) Interconnection example Master/Slave-Mode SPECIFICATIONS TROUBLE SHOOTING This symbol adverts you an important reference note on the following pages. Attend these reference notes by any means, otherwise damage of the device or the vehicle may be caused. -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS PLEASE OBSERVE THE FOLLOWING ADVICES BEFORE THE FIRST OPERATION! DO NOT INSTALL THE DEVICE AT LOCATIONS, WHERE IT THE PURCHASED DEVICE IS ONLY SUITABLE FOR AN OPER- WILL BE EXPOSED TO HIGH HUMIDITY AND DUST. Install ATION WITH A 12V ON-BOARD ELECTRICAL SYSTEM OF A the device at a location, where it will be protected from high VEHICLE. -
Page 4: Installation Instructions
Amplifier 1 Amplifier 1 Vehicle Then uphold the amplifier to the chosen If you own a second ESX XENIUM Screw both amplifiers together by using position and fix the screws through the amplifier, you are able to mount the two... - Page 5 INSTALLATION INSTRUCTIONS ELECTRICAL INTERCONNECTION BEFORE THE CONNECTION For the professional installation of a sound system appropriate wiring kits are available in car audio retailer stores. Attend the sufficient profile section (at least 20 mm ), the suitable fuse rating and the conductivity of the cables when you purchase your wiring kit. Clean and remove rust-streaked and oxidized areas on the contact points of the battery and the ground connection.
-
Page 6: X-One
X - O N E FUNCTIONS AND OPERATIONAL CONTROLS The MASTER OUT / SLAVE IN RCA jacks are suitable to connect an additional amplifier in MASTER/SLAVE mode. Attend therefor the chapter Interconnection Example: MASTER/SLAVE on page 19. The LINE INPUT RCA jacks must be connected with the RCA output jacks of the headunit. Both jacks must be used. If your headunit provide only one RCA jack, you need to split the signal with a y-connector. -
Page 7: Interconnection Example Low Pass-Mode (Standard Subwoofer Operation)
X - O N E INTERCONNECTION EXAMPLE Low Pass-Mode (Standard Subwoofer Operation) Connect the bass remote controller and the remote terminal on the amplifier with the enclosed cable. Switch position MASTER OUT Connect stereo RCA output (R/L or SUB OUT) of the headunit with LINE INPUT R/L of the amplifier Subwoofer 1 –... -
Page 8: Interconnection Example Master/Slave-Mode
X - O N E INTERCONNECTION EXAMPLE Master/Slave Mode Connect Stereo RCA output (L/R or SUB OUT) of the headunit with the LINE INPUT L & R of the MASTER amp Connect Stereo RCA output MASTER OUT of the MASTER amp with the RCA input SLAVE IN of the SLAVE amp. - Page 9 X - O N E INTERCONNECTION EXAMPLE 1 Subwoofer with a Single-Voicecoil MASTER SLAVE MASTER/SLAVE Link like described on page 19. The Impedance may not Subwoofer be lower than 2 ohms. 2 – 8 Ohms INTERCONNECTION EXAMPLE 1 Subwoofer with a Dual-Voicecoil MASTER/SLAVE Link MASTER SLAVE...
-
Page 10: Specifications
SPECIFICATIONS MODELS X-ONE CHANNELS CIRCUIT CLASS D Digital OUTPUT POWER RMS 13,8 V Watts @ 4 Ohms 1 x 300 Watts @ 2 Ohms 1 x 500 Watts @ 1 Ohm 1 x 750 OUTPUT POWER MAX. 13,8 V Watts @ 4 Ohms... -
Page 11: Trouble Shooting
TROUBLE SHOOTING STATUS INDICATOR & PROTECTION CIRCUIT The STATUS INDICATOR (ESX LOGO) is located on the top side of the amplifier. 1. If the STATUS INDICATOR lights up, the amplifier is turned on and is ready for operation. You find also a POWER LED on the remote controller which owns the same function. 2. - Page 12 TROUBLE SHOOTING Malfunction: no function Reason: Remedy: 1. The power supply connection of the device is not correct. Recheck 2. The cabels have no mechanical or electrical contact. Recheck 3. The remote turn-on connection from the headunit to the amplifier is not correct. Recheck 4.
- Page 13 CAR AUDIO SYSTEMS Audio Design GmbH · www.audiodesign.de Am Breilingsweg 3 · D-76709 Kronau (Germany) Tel. +49 (0)7253 - 9465-0 · Fax +49 (0)7253 - 946510...