GE JCP910 Installation Instructions Manual

30" electric cooktop
Hide thumbs Also See for JCP910:

Advertisement

Installation
Instructions
Questions? Call 1.800.361.3400 or visit our Website at: www.GEAppliances.ca
CAUTION: BEFORE YOU BEGIN
Read these instructions carefully and completely.
IMPORTANT –
inspector's use.
IMPORTANT –
ordinances.
• Note to Installer – Be sure to leave these instructions with
the Consumer.
• Note to Consumer – Keep these instructions for future
reference.

PARTS INCLUDED

4 screws
2 Hold Down Brackets
MATERIALS NEEDED
Junction
Box
Pub. No. 31-10602
01-05 JR
Printed in the United States
30" Electric Cooktop
JCP910, JCP930
Save these instructions for local
Observe all governing codes and
Foam Strips
Wire Nuts
• NOTE: This appliance must be properly grounded.
• Skill level – Installation of this appliance requires basic
mechanical and electrical skills.
• Completion time – 2–3 hours.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty.

TOOLS YOU WILL NEED

1/8" Drill Bit and
Electric or Hand Drill
Ruler or
Straightedge
1
Pencil
Phillips
Screwdriver
Hand or
Saber Saw

Advertisement

Table of Contents
loading

Summary of Contents for GE JCP910

  • Page 1: Installation Instructions

    Installation 30” Electric Cooktop Instructions JCP910, JCP930 Questions? Call 1.800.361.3400 or visit our Website at: www.GEAppliances.ca CAUTION: BEFORE YOU BEGIN • NOTE: This appliance must be properly grounded. Read these instructions carefully and completely. IMPORTANT – • Skill level – Installation of this appliance requires basic •...
  • Page 2: Important Safety Instructions

    Installation Instructions IMPORTANT SAFETY INSTRUCTIONS FOR YOUR SAFETY ELECTRICAL REQUIREMENTS • For Personal Safety remove the house fuse or open This appliance must be supplied with the proper the circuit breaker before beginning installation. voltage and frequency, and connected to an Failure to do so could result in serious injury individual, properly grounded branch circuit, or death.
  • Page 3 Installation Instructions PRE-INSTALLATION CHECKLIST ❏ Remove Installation Instructions from literature pack and read them carefully before you begin. CAUTION: The electrical power to the Be sure to place all literature, Owner’s Manual, cooktop supply line must be shut off while Installations, etc.
  • Page 4 Installation Instructions PREPARING THE OPENING B1 REQUIRED CLEARANCES B4 CUTOUT DIMENSIONS OF THE COUNTERTOP The following MINIMUM clearance dimensions must be maintained. 13″ MAX. depth of unprotected To insure accuracy, it is best to make a overhead cabinets 1 1/2″ MIN. clearance template when cutting the opening in from cutout to side the counter.
  • Page 5: Cinstalling The Cooktop

    Installation Instructions INSTALLING THE COOKTOP C1 INSTALLING THE C4 REMOVE HOLD JUNCTION BOX DOWN BRACKETS Install an approved junction box where it will Remove the Hold Down Brackets and screws be easily reached through the front of the from the poly bag. cabinet where the cooktop will be located.
  • Page 6: Delectrical Connections

    Installation Instructions ELECTRICAL CONNECTIONS CONNECT LEADS TURN OFF POWER Turn off power at the circuit breaker or remove Connect the red and black leads from the fuses to the cooktop branch circuit. cooktop conduit to the corresponding leads in the junction box. Ground wire Black...
  • Page 7 Installation Instructions PRE-TEST CHECKLIST ❏ ❏ Remove all protective film if present, and any Check level of appliance. ❏ stickers. Check that the cooktop is properly grounded. ❏ Check to be sure that all wiring is secure and not pinched or in contact with moving parts.
  • Page 8 Installation Instructions OPERATION CHECKLIST ❏ ❏ Remove all items from the cooktop surface. NOTE TO ELECTRICIAN: ❏ The power leads supplied with this appliance Turn on the power to the cooktop. (Refer to your are CSA-recognized for connections to larger gauge Owner’s Manual.) Verify that all surface units household wiring.

This manual is also suitable for:

Jcp930

Table of Contents