Page 1
(ver.0.3) 1 / 20 Color line scan camera Instruction Manual Model: TLC-7500CLD TAKENAKA SENSOR GROUP TAKENAKA SYSTEM CO.,LTD. □ H e a d O f f i c e 86-66 Nomizo-cho Otsuka Yamashina-ku 607-8135 Kyoto JAPAN TEL:+81-75-593-9300 FAX +81-75-593-9790 □ C a m e r a D e p t .
............... 5. Camera I/O ............... 5-1. Connector pin assignment of the Power connector 5-2. Connector pin assignment of the Camera Link connector 6. How to change ............... 6-1 Fine adjustment of ODD/EVEN video signal 6-2 How to change camera GAIN 7.
3 / 20 1. Outline TLC-7500CLD is the color line scan camera with 3-lines of 7500-pixels CCD image sensor and has the following features. 2. Features ● Capable of performing high-resolution inspection with 7500-pixels CCD image sensor. ● The pixel size is large enough (9.325μm×9.325μm) to capture high S/N images.
M 72, P = 0.75 mm 5. Camera I / O 5-1 Signal I/O The line scanner is connected to the Frame grabber board via two Camera Link cables. Camera Link (R, G, B 8bit) Base / Medium Configuration Video monitor signal...
Page 5
5 / 20 5-2 Camera Link connector Camera Link connector pin-out Base Configuration Connector Camera Control Configration Pin No. Signal name Pin No. Signal name Signal name Connection Shield Shield EXSYNC Spare Spare Spare Xclk - Xclk + SerTC+ SerTC-...
6 / 20 5-4 Power connector Power connector pin assignment Pin No. Signal name Pin No. Signal name +12V GND +12V GND +12V GND Conforming connector HR 10A-7P-6S 5-5 Video monitor signal selector switch R B G It is able to monitor the video signal of each RGB line from the Video monitor terminal by pressing the “Video monitor signal selector switch”.
8 / 20 8. Serial communication protocol [Network transmission setting] Baud rate :9600bps Data Length :8bit Start Bit :1bit Stop Bit :1bit Parity :Non Xon / Xoff Control :Non [Communication overall] 1. Referring To refer to the status of the camera. e.g.
Page 9
9 / 20 [ Description of exceptional case] *NG is returned in case of command input error or inputting nonexistent command. e.g. : Command input error (Gain position No. is not designated. ) Input: ch1gain=96 Output: NG e.g. : Input of nonexistent command Input: chake Output: NG...
Page 10
10 / 20 【Command Protocol】(PC->Camera) Command Format Argument Return value Explanation Name Get Ctrl ctrl[?]<CR> 0:Dip Switch Get DIP switch status / communication value 1:Com selection Set Ctrl ctrl=N<CR> N=0:Dip Sw Set DIP switch status / communication value N=1:Com selection dipsw<CR>...
Page 11
11 / 20 Command Format Argument Return value Explanation Name chXoffset[?]<CR> X=1-6:ch 0-31: Get the offset level of each channel chXoffset offset level chXoffset=N<CR> X=1-6:ch Set the offset level of each channel chXoffset N=0-31: offset level * This parameter can set when ctrl is 1 only Check check<CR>...
12 / 20 Exposure control UCL-Exposure control (TLC-7500CL) Li n e p er io d e xp o su r e (ex pc=0 ) Ex pos ure dur ing eac h p erio d o f E XT.S YNC (CC1 ) ST- 1 S T-2 ST- 3...
13 / 20 Setup steps of Hyper terminal. [Applicable camera] TL-□□□□CL, TL-□□□□UCL [Network transmission setting] Baud rate 9600 bps Data length 8 bit Start bit 1 bit Stop bit 1 bit Parity Xon / Xoff control...
Page 14
14 / 20 [Setup of Hyper terminal ] 1) Select “Start”→ “Programs”→”Accessories”→”Communications”→”Hyper Terminal” 2) The windows will appear with the picture below. 3) When the next picture appears, enter any name.(e.g. GMA_RS232C) Then click the “OK” button. 4) When the next picture appears, select “ COM? ” on Connect using. (? changes depending on the setting of the computer.
Page 15
15 / 20 5) When the next picture appears, select each items as follows.(9600,8,None,1,Non) Then click the “OK” button. 6) The next picture will appear. 7) Select [File]→ [Properties]...
Page 16
16 / 20 8) When the next picture appears, select “Settings” tag. 9) When the next picture appears, click the “ASCII Setup” button. 10) When the next picture appears, select each items as follows.(☑, ☑, 0, 0,☑, blank, blank) Then click the “OK” button. 11) The screen display will return to the screen of 9).
Page 17
17 / 20 12) End of setup. Confirm the connection of the camera , enter “check” on the screen below and then send it out. If “OK” is displayed on the screen, communication processing has been completed. 13) Select “Start”→ “Programs”→”Accessories”→”Communications”→”Hyper Terminal” →”(*1) ”, when to launch the Hyper terminal again with the same settings after having exited the above screen.
18 / 20 11. Color gap correction ctrl=1 rgb_on = 1 rgb_dir = 0 color gap scan derection rgb_ldelay = 4 value setting Current setting is in the status as above. If the object flow is in the reverse direction, set the color gap scan direction as below, rgb_dir = 1 When it is needed to change the correction value of the color gap, set up the value of n rgb_ldelay = n...
In cases like this, consider to adjust shutter speed setting of the camera or to use the DC lighting or high- frequency lighting. ■ Use a ceramic driver to adjust ODD/EVEN video signal. ■ Do not remove a cover and do not insert/remove a Camera Link connector when applying current to the equipment. It causes the equipment to malfunction. Attention ■...
20 / 20 12. External dimensions 2-M4(4Faces) Light-receiving face 1 20 2 8.8 1 00 4-M4 Ba se Sy nc V id eo M ed iu m Pow er ( 12 .5 ) 37 .3 5 6.3 2- M6 1/ 4" -2 0 UN C (Screw for tripod)...