Related Manuals for Sapido AU-5125
Summary of Contents for Sapido AU-5125
- Page 1 Dual-Band High Power Wireless Dongle Wireless N Dual-band High Power USB Adapter AU-5125 Networking User Manual v1.0.0...
-
Page 2: Fcc Statement
IMPORTANT NOTE FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance20cm between the radiator & your body. http://www.sapido.com.tw/ USER MANUAL V1.0... - Page 3 "Council Directive on the Approximation of the Laws of the Member Sates relating to Electromagnetic Compatibility" (89/336/EEC; 92/31/EEC; 93/68/EEC). The Declaration of Conformity can be found at the Sapido regional website. www.sapidotech.de CE Information of Disposal The electric and electronic equipment or unit which is labeled with crossed-out wheeled bin may not be disposed of with household waste.
-
Page 4: Table Of Contents
User Guide of AU-5125 Installing the software of USB Adapter ......... 5 Configuring your wireless network (with Wireless Utility).... 7 Wi-Fi Protect Setup (WPS)............14 Pin Input Config (PIN) ............14 Push Button (PBC) ..............19 Radio Off ..................22 Disable Adapter ................23 Mode Selection................24 Access Point Mode ...............26... -
Page 5: Installing The Software Of Usb Adapter
1. Select the setup file to install. The setup program will detect user’s language automatically. 2. The setup program will install the driver and utility to computer. Please click the “Next” button to continue. 3. The software installation should begin. This may take a few minutes. http://www.sapido.com.tw/ USER MANUAL V1.0... - Page 6 4. Once the installation success, click “Yes” to restart your system (recommended). Otherwise, click “No” to restart your system later. 5. Once the installation complete, you may now configure your wireless network. http://www.sapido.com.tw/ USER MANUAL V1.0...
-
Page 7: Configuring Your Wireless Network (With Wireless Utility)
2. Double click on the computer with wireless signal icon in your taskbar or the shortcut icon on the desktop. 3. It should pop up the Wireless Utility window. And then utility shows the connecting wireless network that connected automatically or was the default network in profile. http://www.sapido.com.tw/ USER MANUAL V1.0... - Page 8 4. Click the “Available Network” tab to the wireless network surveying page. Click the “Refresh” button to scan the area for wireless network(s). Once the scan completed, select the desired wireless network from the list and double click it or click the “Add to Profile” button. http://www.sapido.com.tw/ USER MANUAL V1.0...
- Page 9 (WEP, WPA, WPA2, and etc.) set on your wireless network, simply click the “OK” button and skip to step7. If you do have wireless securities on your wireless network, configure the security setting in “Wireless network security” column. http://www.sapido.com.tw/ USER MANUAL V1.0...
- Page 10 - If you have WPA-PSK or WPA2-PSK, typically you only enter your key in the “Network Key” and type again to confirm it. - If you have 802.1x configure, typically you only configure your setting in 802.1x configure column. http://www.sapido.com.tw/ USER MANUAL V1.0...
- Page 11 7. After connected to wireless network, utility will back to “General” page and show the wireless network status. Once the wireless network connected successfully, the Network Address will show the dongle has gotten the IP address from DHCP. http://www.sapido.com.tw/ USER MANUAL V1.0...
- Page 12 8. Click the “Profile” tab to check the profile page. The wireless network configuration has added in Available Profile(s). It could remove, edit, duplicate and set default the profiles in this page. http://www.sapido.com.tw/ USER MANUAL V1.0...
- Page 13 USER MANUAL V1.0...
-
Page 14: Wi-Fi Protect Setup (Wps)
If you want to connect to a specific AP, please click the “Yes” button. Or please click the “No” button to continue and skip to step3. Note: Every time you click the tab to change the page, the PIN code will be changed. http://www.sapido.com.tw/ USER MANUAL V1.0... - Page 15 2. Select the specific AP which you want to connect. If you can not find the WPS AP in this page, please click the “Refresh” button. And then click the “Select” button. http://www.sapido.com.tw/ USER MANUAL V1.0...
- Page 16 Enter the PIN code into client pin number and then clicks the “Start PIN” button. Note: The PIN function in AP should be started before the WPS setup in dongle times out. http://www.sapido.com.tw/ USER MANUAL V1.0...
- Page 17 USER MANUAL V1.0...
- Page 18 4. Once the WPS connected successfully, wireless utility will show the connection status. http://www.sapido.com.tw/ USER MANUAL V1.0...
-
Page 19: Push Button (Pbc)
Push Button (PBC) 1. Click on the “Push Button Config (PBC)” button. Note: The PBC button can click the visual button on the page or push the physical button on AP. http://www.sapido.com.tw/ USER MANUAL V1.0... - Page 20 2. Dongle is waiting for the other AP to start the PBC function. The other AP starts the PBC function should be before dongle WPS times out. http://www.sapido.com.tw/ USER MANUAL V1.0...
- Page 21 3. Once WPS connected successfully, Wireless Utility will show the connection status. http://www.sapido.com.tw/ USER MANUAL V1.0...
-
Page 22: Radio Off
Radio Off Enable the Radio Off will turn off the radio function. It means dongle will turn off the wireless function. The wireless network connection will be disconnected. http://www.sapido.com.tw/ USER MANUAL V1.0... -
Page 23: Disable Adapter
Disable Adapter Disable the dongle will turn off the USB adapter function. It means all functions of dongle will be turn off. http://www.sapido.com.tw/ USER MANUAL V1.0... -
Page 24: Mode Selection
Mode Selection Users can switch between Station and Access Point modes. http://www.sapido.com.tw/ USER MANUAL V1.0... - Page 25 Mouse double click the SoftAP network adapter to switch to soft AP mode and disable “Disable Adapter” to enable soft AP mode If you do not want to use access point mode，please disable softap network adapter（enable ”Disable Sort AP”） ，then dongle can get better performance http://www.sapido.com.tw/ USER MANUAL V1.0...
-
Page 26: Access Point Mode
Setting Internet Connection Sharin n n n g g g g （ （ （ （ ICS ICS） ） ） ） Select one interface for network sharing Network Name Give a SSID to shared network. Channel Select a channel for shared network. Network Authentication Select authentication type for shared network. Data encryption http://www.sapido.com.tw/ USER MANUAL V1.0... -
Page 27: Uninstalling The Software
2. The uninstall window should pop up. Click on “Yes” button. 1. The uninstall process should begin and may take a few minutes. Once completed, click “Finish” to close the uninstall window. 2. Once it’s complete, click the “Finish” button to exit the uninstall program. http://www.sapido.com.tw/ USER MANUAL V1.0... - Page 28 USER MANUAL V1.0...
-
Page 29: Wireless Zero Configuration Troubleshooting
Config”, such as following figure, please do the following steps. 1. Click on your start menu and then click the “control panel” into control panel. Next click the “Administrative Tools”. 2. Click on the “Services” item. http://www.sapido.com.tw/ USER MANUAL V1.0... - Page 30 3. It will pop up the Services window. Select the “Wireless Zero Configuration” or “Wireless Configuration” item and double click it. http://www.sapido.com.tw/ USER MANUAL V1.0...
- Page 31 4. It will pop up the Wireless Zero Configuration Properties window. The “Service status” should be in “Stopped” state now. Click the “Start” button to enable the Wireless Zero Configuration function. http://www.sapido.com.tw/ USER MANUAL V1.0...
- Page 32 5. Once the setting completes, the “Service status” become to “Started”. Click the “OK” button to finish it and the dongle Wireless Utility can see the check option of “Windows Zero Config”. http://www.sapido.com.tw/ USER MANUAL V1.0...
- Page 33 USER MANUAL V1.0...
-
Page 34: Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. http://www.sapido.com.tw/ USER MANUAL V1.0...
Need help?
Do you have a question about the AU-5125 and is the answer not in the manual?
Questions and answers