Summary of Contents for EasyTig Easytig 200AC/DC
- Page 1 EasyTig Operation Manual TIG AC/DC Series Inverter Welding Machine Model: Easytig 200AC/DC Easytig 300AC/DC Easytig 315AC/DC Hong Kong EasyWeld Limited...
- Page 2 CONTENTS - Introduction - Warning - Main Parameter - Installation and Operation - Caution & Pre-cautions - Maintenance - Troubleshooting...
-
Page 3: Warranty
Introduction The EasyTig series of Welders is a revolutionary new approach to Welding technology. Easyweld introduced a more efficient way to manufacture top quality machines while keeping the cost of operation and repairs lower. This was accomplished using several new approaches to the mainstream technology. One of these methods is our proprietary plug &... - Page 4 CAUTIONS: •A certain switch is needed to protect the machine from electricity-leaking. •Please use welding tools of good quality. •The workers should be qualified for welding. Electric-shock: it may be fatal to life. • Install the earth cable to the standard. •...
- Page 5 The use and development of inverter technology in welding benefits from the invention of high power electronic spare parts, esp. IGBT, the employ of which greatly reduces the volume and weight of main parts, e.g. transformer and anti-electricity, thus making our machines able to work under HF 20KHZ. We also employ PWM and CPU-control to make the welding current stable, accurate and easy to adjust;...
- Page 6 THE MAIN PARAMETER TYPE TIG 200AC/DC TIG 300AC/DC TIG 315AC/DC Power voltage AC220V±15% AC380V±15% 50/60Hz 50/60HZ Rated input current Power capacitance 4.5 KVA 8.5KVA 8.9KVA Rated output current 200A 300A 315A Range of output 20~200A 20~300A 20~315A current Arc force (A) 0~100 0~100 0~100...
- Page 7 A. Exchange switch: 1. ARC/TIG exchange switch: Place the switch on “ARC”; it’s for MMA welding; Place the switch on “TIG”, it’s for AC or DC Tig welding. 2. AC/DC Exchange switch: Place the switch on “AC”; it’s in AC mode for welding aluminum; Place the switch on “DC”;...
-
Page 8: Installation
6. Arc force adjustment: If you adjust this switch at MMA, then it can change the welding characteristic of the little current. 7. Base current: At DC TIG pulse, this button can adjust the volume of the valley current. 8. Pulse frequency switch: At DC TIG, and place the DC/PULSE at PULSE, this switch can adjust the pulse frequency (0.5-300HZ). -
Page 9: Operation
board, and tighten it in clockwise direction. 7. Connect the two-cored air plug of the foot switch respectively to the two-cored and three-cored sockets on the panel board. After finishing all the work above, you can start welding. OPERATION 1. Turn on the power switch, the fan begins to work. 2. - Page 10 INSTRUCTIONS TO DC TIG: 1. Make “AC/DC” to “DC” place. 2. PULSE/DC switch, if you put it at PULSE, you can adjust the buttons for Base current adjustment. Set pulse adjustment or clear width adjustment to achieve the welding efficiency that you need. 3.
-
Page 11: Safety Tips
Safety tips TIG welders are equipped with over-voltage and over-current and over-thermal protection circuit, when the output voltage, output current and inner temperature is over the rated ones, the machine will stop working automatically. But over-use (e.g. over-voltage) may damage the welding machine, so pay attention to the following tips: 1) Make sure of good ventilation TIG welders are large technical welding machines. - Page 12 MAITENANCE WARNING: All maintenance and checking work should be carded out under the circumstance of light off .Make sure the power plug is pulled off before you open the case. 1) Use clear and dry compressed air to remove the dust in certain period, if the machine is working under heavy-polluted environment, clear it daily.
- Page 13 Checking breakdown Cautions: The operators are supposed to have enough knowledge of electric-gas and common sense of safety, and concerning certificates are needed. We suggest you contact us before operation and meanwhile get permission BREAKDOWN POSSIBLE CAUSES SOLUTION 1. No power supply or 1.