DS9860W Control play Use advanced sound settings Play from an external device 6 Charge your iPod/iPhone/iPad through USB socket 7 Update firmware Option 1: Update through Philips SoundStudio (recommended) Option 2: Update through a USB mass storage device or PC/Mac...
1 Important n This product may include batteries. Please refer to safety and disposal instructions for batteries in this user manual. o Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily Safety operable.
Follow local rules and requirements and other relevant provisions never dispose of the product and batteries of Directive 1999/5/EC. You can find the with normal household waste. Correct disposal Declaration of Conformity on www.philips.com/ of old products and batteries helps prevent support. negative consequences for the environment and human health. Any changes or modifications made to this...
Environmental information Note All unnecessary packaging has been omitted. We have tried to make the packaging easy to • The type plate is located on the bottom of the apparatus. separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company.
• A Wi-Fi certified router Apple AirPlay technology enables you to play • A host for your iTunes music library, your iTunes music library, hosted on a Mac, PC, for example, an iPod touch/iPhone/iPad iPhone, iPod touch, or iPad on any AirPlay- installed with iOS 4.3.3 (or later) or a Wi-Fi enabled device (for example, your DS9860W) enabled PC/Mac installed with iTunes 10.2.2 connected to the Wi-Fi network. (or later) With an AirPlay-enabled device (for example, Your DS9860W should be connected to the your DS9860W), you can: same local network as your iTunes host device • stream audio from your iTunes music library...
• iPad (4th generation) • Connect an iOS device through an • iPad mini Apple USB cable (not supplied) for • iPad (3rd generation) charging. • iPad 2 • Connect a USB mass storage device • iPad for firmware upgrade. • iPod touch (5th generation) • iPod touch (4th generation) • Turn the unit on/off.
Overview of the remote control • Turn the unit on/off. • Select the AirPlay device audio source. c +/- • Adjust volume. • Mute or restore volume. • Skip to the previous/next track. • Start or pause play. • Select the MP3 link audio source.
Insert fully the end of a speaker cable with • the wall power socket. red mark into the left red (+) connector. Screw the left red (+) connector to secure Turn DS9860W on the cable. Insert fully the end of a speaker cable After proper power connection, the unit without red mark into the left black (-) switches on automatically.
» The boot-up takes about 25 seconds. Note » During boot-up, the indicator on the • Before you press any function button on the remote back of the main speaker blinks yellow. control, first select the correct source with the remote » After boot-up, for first-time setup, the control instead of the main unit. • WI-FI STATUS indicator turns solid If you are not going to use the remote control for a long time, remove the battery.
Fi network for iPhone/iPad or a Wi-Fi on page 12). enabled PC/Mac. AirPlay Before connection of DS9860W to you home Wi-Fi network, make sure that: a your Wi-Fi router is powered on and working properly. b DS9860W has been powered on and booted up successfully (see 'Turn DS9860W on' on page 8).
» The following dialog box is displayed. Note • Before you press any button on DS9860W, make sure that DS9860W has been booted up successfully (see 'Turn DS9860W on' on page 8). Press the WPS button on your home Wi-Fi router. Shortly after step 1, press WI-FI SETUP on the back of the main speaker. Tap ALLOW (allow) to share your Wi-Fi »...
PBC function from the router configuration pages. See (see 'Connect your Wi-Fi enabled device the user manuals of the specific routers for details. to the newly created Wi-Fi network' on • If the WI-FI STATUS indicator on DS9860W stays page 13). yellow, it means that the Wi-Fi connection has failed. Please wait for 2 minutes and try again. If the problem Open the built-in web page of DS9860W...
Select Philips_Install XXXXXX from the • After you finish manual Wi-Fi setting for DS9860W, this new Wi-Fi network disappears. list of available networks. • If you fail to enter Assisted Wi-Fi Setup mode, power off DS9860W and power on it, then try again after successful boot-up. • Make sure that there are no other Philips AirPlay- enabled devices in Assisted Wi-Fi Setup mode at the same time. Multiple new Wi-Fi networks created this way may interfere with each other.
Philips_Install XXXXXX Philips_Install XXXXXX Select Philips_Install XXXXXX from the list of available networks. Philips_Install XXXXXX Wait until successful Wi-Fi connection on your iPod touch/iPhone/iPad. » is displayed at the upper left corner of your iPod touch/iPhone/iPad. • If Philips_Install XXXXXX is not in the list, try to scan Wait until successful Wi-Fi connection on the available Wi-Fi networks again.
Follow the on-screen instructions to configure and confirm the internal Wi-Fi settings of DS9860W. » After a while, the WI-FI STATUS indicator on the back of DS9860W stops blinking and turns solid green, and the unit beeps. » DS9860W is connected to your existing home Wi-Fi network successfully. Configure the internal Wi-Fi settings of DS9860W On the DS9860W configuration web page, you can configure the internal Wi-Fi settings of DS9860W for connection of DS9860W to your existing home Wi-Fi network.
• If the WI-FI STATUSindicator on DS9860W does not stay green steadily, it means that the Wi-Fi connection has failed. Please power off both your Wi-Fi router and DS9860W and then power on them again to see whether DS9860W can be connected to your home Wi-Fi network. If the problem remains, try the above procedures again. •...
Fi settings or rename your device through Safari Philips SoundSphere XXXXXX If you use Safari on your Wi-Fi enabled PC/ Mac, you can also select 'Philips SoundSphere XXXXXX' from the Bonjour pull-down list to enter the DS9860W configuration web page Change the internal Wi-Fi settings or directly. Here, you can change the internal Wi-Fi rename your device on the web page.
Your iTunes device can be an iPod touch/iPhone/iPad installed with iOS 4.3.3 (or later) or a Wi-Fi enabled PC/Mac installed with iTunes 10.2.2 (or later). • For iPhone 4S users: To ensure optimal performance Select Philips SoundSphere XXXXXX (or of AirPlay streaming, upgrade your iPhone 4S to iOS user customized name) from the AirPlay 5.1 or later. list. • To play music wirelessly, make sure that your iPod touch/iPhone/iPad is disconnected from the USB socket on the back of the main speaker.
Select a media file and start play. » After a while, you will hear music from DS9860W. Select Philips SoundSphere XXXXXX (or user customized name) from the AirPlay list. Philips SoundSphere XXXXXX Select a media file and start play. » After a while, you will hear music from DS9860W. Note • If you fail to hear music after successful setup, do one of the following on your iPod touch/iPhone/iPad: • (1) Disconnect and then re-connect to the same Wi-Fi router again;...
For advanced sound settings and additional features, you can use your iPod touch/iPhone/ • iPad to download the Philips SoundStudio app When you stream audio from your iTunes music library on a PC/Mac, you can select more than one AirPlay- from Apple App Store. It is a free application enabled devices (if available) at step 3 to stream music from Philips.
MP3-LINK Connect the supplied MP3 link cable to: • the MP3-LINK socket on the back of DS9860W. • the headphone socket on an external audio player. Press to select the MP3 link source. Start play on the external audio player.
7 Update firmware www.philips.com/support Warning XXXX • Always connect your DS9860W to AC power for firmware upgrade. Never power off your DS9860W during firmware upgrade. You can update the firmware either through a USB mass storage device (recommended) or from a PC/Mac. XXXX. zip Option 1: Update through On your PC/Mac, go to www.philips.com/ Philips SoundStudio support. (recommended) Enter the model number to find the latest firmware upgrade file available.
Plug the USB mass storage device into » DS9860W is connected to the last the USB socket on the back of the main configured Wi-Fi network automatically. speaker. Make sure that DS9860W and your PC/ Mac are connected to the same Wi-Fi router.
8 Product General information information AC power Wireless SoundSphere speakers: 100-240V~, 50/60Hz Note Operation Power 22 W • Product information is subject to change without prior Consumption notice. Standby Power < 0.5 W Consumption Dimensions 265 in diameter x - Each speaker 410 mm Specifications Weight...
WPS-PBC method but fails to connect • Make sure that there is power at the AC to DS9860W, try the manual Wi-Fi setup outlet. method (see 'Method 3: Connect to a non-WPS Wi-Fi router' on page 12). No sound •...
iTunes or DS9860W. • Do one or all of the following: Video streaming or FTP downloads may • Move DS9860W closer to your Wi-Fi overload your router and therefore may router. cause interruptions during AirPlay music • Remove any obstacles between DS9860W play. Try to reduce the load of your router.
WOOX Innovations, and is the manufacturer of the product. WOOX Innovations is the warrantor in relation to the product with which this booklet was packaged. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. DS9860W_10_UM_V3.0...