Important Safety Information End user must read this section before operating this unit. Operation of the unit is permitted only if traffic conditions are suitable and you are absolutely sure that you, your passengers or other motorists are not endangered, obstructed or inconveni- ienced.
Connecting the System Important notes Do not route wires where they will be exposed to high temperatures. If the insulation heats up, wires may become damaged, resulting in a short circuit or malfunction and permanent damage to the navigation system. Do not cut the GPS aerial cable to shorten it or use an extension to make it longer.
Page 4
Connecting the System About Parking Wire Caution: In order to avoid any accident, the driver must not watch video while driving. This unit is designed to not allow watching moving video while driving. Park your car in a safe place and engage the parking brake before watching moving video.
Page 5
Connecting the System Wiring Diagram - Audio / Video Connections GPS AERIAL Note: Please refer to the "Installing the GPS Aerial". For the proper mounting or installation of this GPS AERIAL. YELLOW VIDEO INPUT VIDEO IN VCR or DVD AUDIO INPUT (RIGHT) AUDIO IN R GAME CONSOLE WHITE...
Page 6
Connecting the System Wiring Diagram - Power / Speakers (Not supplied) ANTENNA FUSE ANTENNA EXTENDER JACK CABLE 20-PIN AUDIO/POWER HARNESS (See Figure 1 ) (Not supplied) RCA-TO-RCA CABLES GREY WHITE REAR CHANNEL BLACK WHITE FRONT CHANNEL BLUE/WHITE STRIPE Connect to power amplifier, If not used, POWER Tape bare end of wire.
Installing the GPS Antenna / Aerial Parts Supplied Setting Description GPS aerial Metal sheet Clamp (5 pcs.) Waterproof pad When installing the aerial inside the vehicle (on the rear shelf) Affix the metal sheet on as level a surface as possible where the GPS antenna / aerial faces the window.
Installing the GPS Antenna / Aerial End user must read this section before installing the GPS Antenna / Aerial. Caution: Do not cut the GPS antenna / aerial lead to shorten it or use an extension to make it longer. Altering the aerial cable could result in a short circuit or malfunction and permanent damage to the navigation system.
Page 9
Installing the GPS Antenna / Aerial Take care not to pull the antenna / aerial lead when removing the GPS aerial. The magnet attached to the aerial is very powerful and the lead may become detached. The GPS antenna / aerial is installed with a magnet. When installing the GPS antena / aerial, be careful not to scratch the vehicle body.
Installation the Unit Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions or permanent damage to the unit.
Installation the Unit Content Dashboard Nut (5mm) Spring washer Screw (4X12mm) Screw Support Strap Be sure to use the support strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle Plain washer Removing the unit Content...
Page 12
Installation the Unit Trim Plate Installation Push the trim plate against the chassis until it is fitted. You must do this before you install the front panel, otherwise it can't be attached. Din rear-mount (method B) Installation using the screw holes on the sides of the unit.Fastening the unit to the factory radio mounting bracket.
Page 13
Detachable Front Panel (D.F.P.) Removing the detachable front panel (D.F.P.). RELEASE BUTTON 1. Turn the Power off. 2. Press the Panel Release Button. 3. Remove the D.F.P. D.F.P. Attaching the detachable front panel (D.F.P.) 1. Insert the right side of the D.F.P. Into the main unit.
Panel Open / Close Operation The unit is equipped with the most advanced full logic motorized slide down system.You can enjoy the advance technology with a single press of the " Eject / Open" button. Please read carefully the following operation instruction before operating the unit. Open / close the panel Press the "...
Overview the Unit Front panel main control Eject / Open Panel Panel Angle adjust Release IR Receiver MODE OSD SET UP AS PS GPS MODE MCD 795 4x75WATT MUTE Volume Knob Touch Screen Display SD Card slot for MEDIA PLAYER Detach the Face Insert the Memory...
Disc Can Supports Discs can play with this unit Content Digital Versatile Discs (DVDs) Video CDs (VCDs) Digital Versatile Discs Recordable(DVD+/-R) Digital Versatile Discs Rewritable(DVD+/-RW) Compact Digital Video (VCD) Compact Discs (Cds) CD Recordable (CD-R) CD Rewritable (CD-RW) Discs which can not be played Note on region code 8 cm Disc DVD players and DVD...
Page 17
Formats Can Playback Audio format can playback Playback CD-DA and MP3 or WMA digital music file on CD-ROM or DVD-ROM or USB or Memory Card. Note of MP3 and WMA: Support Maximum 2000 files. Maximum 30 characters display. Supported Sampling frequencies; 32kHz, 44.1kHz, 48kHz. Supported Bit-Rates: MP3=8 ~320kbps variable bit rate;...
Remote Control Operations VOLUME AUDIO GOTO NAVI LOUD MODE VOICE OPERATIONS: SYSTEM TUNER Short Long Short Long Short Long Short Long Short Long Press Press Press Press Press Press Press Press Press Press Mute Power Open Angle Angle Angle Eject Angle Eject Angle...
Page 19
Remote Control Operations VOLUME AUDIO GOTO NAVI LOUD MODE VOICE OPERATIONS: SYSTEM TUNER CD/MP3/WMA Short Long Short Long Short Long Short Long Press Press Press Press Press Press Press Press Memory Track NO. Access Numeric 5 File NO. Access Memory Track NO.
General Operations MODE Main Menu Media Player Tuner AV-In OSD SET UP Setting AS PS GPS MODE MCD 795 4x75WATT MUTE Power On / Off Button Long press the POWER button for more than 3 seconds or short press any other button on the front of the panel (except the Eject / Open) to turn on the unit.
Page 21
General Operations Panel Angle Adjustment End user can adjust the panel viewing angle of the display to obtain the optimum viewing angle inside the vehicle There are TWO angles can be adjusted by Long pressing the panel Eject / Open button: 1)1st long press to get into Angle 1 2)2nd long press to get into Angle 2 3)3rd long press to resume to the normal position...
Page 22
General Operations Sub-woofer Short press the SUB-W button for less than 3 seconds to turn on the Sub-woofer function. Press the SUB-W button again to turn off the Sub-woofer function. GPS Mode End user can switch the TFT display between the playback mode and GPS NAVIGATION / MAP screen by following: 1.
Tuner operations MODE Main Menu Media Player 104.00 FMSELECT Tuner AV-In 10:30 87.50 90.00 98.00 OSD SET UP Setting Band AS PS 106.00 108.00 87.50 GPS MODE MCD 795 4x75WATT MUTE Band Function Band Press panel BAND button or touch screen to change between FM bands and AM(MW) bands.
Tuner operations RDS Function The unit is equipped with the following RDS function: - AF Alternative Frequencies - CT Clock Time - PI Program identifications - PS Program service name - PTY Program Type - REG Regional Change - TA Traffic Announcement - TP Traffic program AF function Short pressing panel AF button less than 3 seconds to select AF...
Page 25
Tuner operations PTY Function Long press the SUB-W / PTY button for more than 3 seconds to set into the PTY mode. And then press this button repeatedly to different PTY group as listed below. Once the desired PTY is shown on the preset memory M1 to M6, press this preset memory number to activate the searching of this PTY, the PTY name will appear on the 6 preset buttons.
Media Player This Multi-Media player unit can support the playback of CD Disc, DVD disc, USB Host, SD Memory Card. Note: For more details of this unit supporting playback disc and format. Please see pages of "Disc Can support" & " Format can playback"...
Page 27
Media Player Note: If any media device is not avaiable in this unit, this media souurce will not appear during Mode switch or on the touch screen. Note: This unit only can playback the SD Card which is inserted in the main unit.
Page 28
Media Player Navigation While Media Player Playback Navigation Voice Guidance on or off under Media Player playback This unit will automacitally MUTE the audio output of the Media player when there is announcement from the navigation voice guidance. This function can be activated or deactivated by NAVI tapping on the screen button VOICE...
Page 29
Media Player CD/VCD Disc Operation MODE NAVI NAVI VOICE OSD SET UP AS PS GPS MODE MCD 795 4x75WATT MUTE 1 2 7 Track / File Press the TRACK / FILE UP (7) / TRACK / FILE DOWN (8) button or touch screen (7) / (8) for less than 1 second to move to...
Page 30
Media Player Stop Function Press STOP button or tap touch screen button to stop pla- ying.When playback is stopped,the unit can keep the memory of where the STOP was pressed. Press PLAY and the playback will resume from this point. Press STOP button again, RESUME function will be cancelled and the unit is now in full stop mode.
Page 31
Media Player PBC ( On remote control ) Press PBC button on remote control to choose a VCD disc play mode:PBC_ON or PBC_OFF,when you playing a VCD disc. When pressing PBC button and the player change to PBC _ON playing mode, a PBC list of the disc will be displayed on TV or monitor.
Page 32
Media Player Music / Image / Video File Playback Operation The following display information will appear, if a Multi-Media disc or USB or SD is inserted into this unit. File Info Playing domain statue domain MODE OSD SET UP AS PS GPS MODE MCD 795 4x75WATT...
Page 33
Media Player Note: Other operation are the same as CD / VCD, like repeat, program and so on. Please refer to the CD / VCD Disc Operation section. 10&11 Up / Down / Right / Left / Enter Press on remote control or tap touch screen button to move the cursor.
Page 34
Media Player MMN->IMAGE View-> Slide In Slide mode, when the key ENTE or PLAY is pressed, the " " " " player will show pictures or photos one by one from current picture. It will stop and return back when the last one has been shown, Press "...
Page 35
Media Player DVD Disc Operation 12 13 14 15 16 17 18 MODE NAVI NAVI VOICE OSD SET UP AS PS GPS MODE MCD 795 4x75WATT MUTE 10 11 Once a DVD disc is inserted into the unit, the unit will automatically start the playback from the beginning of the disc and then the DVD MENU or ROOT or TITLE in the DVD disc will appear on the TFT monitor and “ROOT”...
Media Player Stop Function Press STOP or touch screen button to stop playback and show the logo screen. The player will memorize the last position where playback is stopped. Press PLAY or touch screen to resume playback from the positon where playback is stopped ( DVD, VCD 1.1, VCD 2.0 and audio CD).
Page 37
Media Player Next Function Press NEXT button or tap touch screen button when playing a disc, a chapter (DVD), a track (VCD / SVCD / CD), a song (MP3 / WMA), a picture (JPEG) , or a video file (AVI / MPEG4 / MPG/ DAT) is skipped forward accordingly.
Page 38
Media Player Subtitle (On Remote Control) Pressing the SUBTITLE button on remote control, End user may select one of the subtitles language to show it on the screen or to turn off the SUBTITLE. This function is invalid for VCD / SVCD / CD, MP3 / WMA and JPEG. DVD OSD ( D) Short Press AS / PS button, once to display the amount of time played and time remaining on the disc.
Media Player Language Setting Press the or touch screen buttons, move to the Language button. The list of available language will appear: Use the buttons to select the setting. Use the buttons to change among the available language. Press Ok or touch screen to cycle through each possible option or display a list of the available options.
Page 40
Media Player Subtitle The Subtitle setting allows the end user to select a preferred language and to change the subtitle language setup. Audio The Audio setting allows the user to select a preferred language and to change the Audio language setup . Disc The Disc setting allows the user to select a preferred language and to change the Disc menu language setup .
Media Player Display Setting Press on the remote control or touch screen buttons, to move to the Display button. The list of Display options will appear as follow: Use the buttons to select the setting. Use the buttons to change among the avaitable settings. Press Ok or touch screen to cycle through each possible option or display a list of the available options.
Page 42
Media Player TV Type The Display setting allows the user to select the TV type. The following options are available: Angle Mark The Display setting allows the user to select the Angle mark on/off mode.
Media Player Screen Saver End user can use this function to turn on or off the screen saver. Audio Setting Press on the remote control or touch screen buttons, move to the Audio button. The list of Audio optional will appear as follow: Use the buttons to select the setting.
Page 44
Media Player Downmix The Audio setting allows the user to select the Downmix and set downmix setup stereo analog output of this Player. Dual Mono The Audio setting allows the user to select the Dual mono and set dual mono(1+1) setup stereo output of this Player. Dynamic The Audio setting allows the user to select the Dynamic and set the dynamic sound output high volume outputs are softened.
Media Player Parental Setting Press the or touch screen buttons, move to the Parental button. The list of Parental optional will appear as follow: Use the buttons to select the setting. Use the buttons to change among the avaitable settings. Press Ok or touch screen to cycle through each possible option or display a list of the available options.
Page 46
Media Player Once entered the wrong password, the "Wrong Password" message will appear. To re-enter the correct password, end user need to move to "Enter Password " again, and try again. Once entered the correct password, press OK or touch screen "...
Page 47
Media Player When the entered password is not matching, the " Passwords do no match" message will appear. End user should try to re-enter the password again and press the “ OK" or touch screen to confirm. Parental Level This function is to enter the Parental level control setup.
Page 48
Media Player Press the OK or touch screen " " to enter the password. If the password is not correct, the " Wrong Password" message will appear. End user should try to re-enter the correct password again and press the " OK" or touch screen to confirm.
Page 49
Media Player Default Setting the " Default “ function will reset all options and your personal settings to the factory defaults and all your personal settings will be erased. Use the buttons to select the setting. Press the OK or touch screen "...
Page 50
AV-In Mode Caution: In order to avoid any accident, the driver must not watch video while driving. This unit is designed to not allow watching moving video while driving. Park your car in a safe place and engage the " parking brake" before watching moving video. Note: If watch moving video from Disc or AV In source but Parking Brake IS NOT PROPERLY CONNECTED, the...
System Setting Operation To adjust the system Settings of this unit, tap on the main menu screen button to enter into the setting menu, the below Setting menu will appear: Settings Sound Setting button on setting menu screen to access into the sound setting menu, the below menu will appear for selection.
Page 52
System Setting Operation button on the sound setting menu screen to select the level . button to enter in the next page, the below menu will appear for selection. Note: button to be return to the previous page. Setting Control Button Beep Tone Sub-Woofer Output bar on the sound setting menu screen to turn on...
System Setting Operation Display Setting button on the setting menu screen to access into the Display setting menu, the below menu will appear: Setting Control Screen Brightness button on the Display Setting menu screen to select the level . Date & Time Setting bar on the Display Setting menu screen to access into the Date &...
Page 54
System Setting Operation bar to change time format to 24 hours. Calibration bar on the Display Setting menu screen to start the Calibration setting. When the target moves to another position, tap and hold at the center of the new target. Repeat each time to complete the calibration process.
Page 55
System Setting Operation Tuner Setting (Radio) button on setting menu screen to access into the Tuner (Radio) setting menu, the below menu will appear: Setting Control Change Tuner seeking in Local or Distant mode. ( Local = Set the unit to select only strong local stations during automatic tuning Distant=Allowing the radio to stop at a...
Page 56
System Setting Operation GPS Map Setting This setting is for end user to select for run the digital Map which is stored into SD memory card or in the built-in internal memory. button on setting menu screen to access into the GPS Map setting, the below menu will appear: Setting Control...
Page 57
System Setting Operation Note: End user can purchase the authorized digital map and store it into SD Memory Card. Note: This unit ONLY CAN ACCEPT / RUN those digital map purchased from authorized dealers / agents. Any non-authorized digital map CANNOT BE USED on this unit. Note: This unit only can run the SD Card contained with digital map which is inserted into the panel's SD card slot.
System Setting Operation System Information button on the settings menu screen to view the detail system information including serial number of this unit. The system information screen as follow. These information may different from unit to unit. System Information OS Version v06.
Page 59
System Setting Operation Upgrade Setting button on the settings menu screen to access into the upgrade menu, the below menu will appear: Note: Insert SD card with the upgrade files stored before proceeding with the upgrade and then tap on desired upgrade feature button in Upgrade mode.
Page 60
System Setting Operation Setting Control This Upgrade should only be performed by approved sevice center or techinal support from authorized dealer. End user should never try to APP MAP the unit by themselves. This Upgrade should only be performed by approved sevice center or techinal support from authorized dealer.
Page 61
System Setting Operation System Upgrade Setting button on the upgrade settings screen to access into the System upgrade menu, the below menu will appear: Note: System Upgrade should only be performed by approved sevice center or techinal support from authorized dealer. End user should never try to System Upgrade the unit by themselves.
Memory Card Operation 1. Press the MODE button repeatedly on panel or remote control to switch between Tuner -> Disc -> USB - > SD Card - > AV IN Mode. Media 2. Aceess to MAIN MENU and tap MEDIA PLAYER. Tap Player the following buttons to start the playback of the desired media sources:...
USB Operation 1. Press the MODE button repeatedly on panel or remote control to switch between Tuner -> Disc -> USB - > SD Card - > AV IN Mode. Media 2. Aceess to MAIN MENU and tap MEDIA PLAYER. Tap Player the following buttons to start playing the desired media sources: button to play files in USB...
Navigation Operation What is GPS Navigation The term navigation is generally understood to mean the " " location of a vehicle, the determination of the direction and distance from the desired destination and the required route. As navigation aids, stars, prominent landmarks, compass and sat- ellites are used.
Navigation Operation To receive GPS signals successfully You have a clear sight of sky The GPS antenna is not covered The weather is good enough. GPS signal is weaker in bad weather conditions The time needed for establishing a GPS connection ranges from seconds to minutes.
Navigation Operation Conditions Likely to Cause Noticeable Positioning Errors For various reasons such as the state of the road you are travelling on and the state of reception of the GPS signal, the actual position of your vehicle may differ from the position displayed on the map screen.
Page 67
Navigation Operation If you drive in zig-zags. If the road has connected hairpin bends. If there is a loop or similar If you take a ferry. road configuration. If you are driving on a long, If you are on a steep straight road or a gently mountain road with many curving road.
Page 68
Navigation Operation If your vehicle is turned on If you enter or exit a multi- a turntable or simi-lar storey car park or similar structure. using a spiral ramp. If your vehicle’s wheels If you put on chains or spin, such as on a rough change your tyres for ones with a different size.
Page 69
Navigation Operation If you join the road after When you go round a driving around a large roundabout. car park. When starting driving immediately after start-ing the engine. If you turn your navigation system on while driving. Some types of vehicles may not output a speed signal while driving at just a few kilometres per hour.
Navigation Operation Digital Map This unit is pre-loaded with the below digital map marked with Yes inside the INTERNAL BUILT-IN FLASH MEMORY: Maps Pre-Loaded Eastern Europe Western Europe Albania Andorra Belarus Austria BosniaHrz Belgium Bulgaria Denmark Croatia.fbl Finland CzechRep France Estonia Germany Greece...
Page 71
Navigation Operation Start Navigation Mode Caution: For safety reasons, you can not use some of navigation functions while your vehicle is in motion.To enable these funcions, you must stop in a safe place and apply the handbrake. Park your vehicle in a safe place and apply the handbrake. How to get into the GPS Navigation system Please read the below instruction carefully before operating the unit.
Page 72
Navigation Operation When in AV IN Mode, end user can tab on the touch screen, NAVI to bring up the menu, and then press on the button ON THE TOUCH SCREEN to get into the GPS NAVIGATION MODE. NAVI NAVI VOICE End user can press the MODE button repeatedly, until the "...
Page 73
Navigation Operation Attention! If you are using the software product during driving or transportation, we strongly advise you to direct all your attention to driving or transportation, and to Especially do not try to operate, enter data into or obtain data from the software product while driving, because such presents a life hazard, and the lack of proper attention may cause death, injury or matertal damge.
Navigation Operation Highlight Features The following are the highlight navigation features : Navigation Voice Guidance under Tuner or Media Player playback During the navigation mode, music of Tuner or Media player can still be heard. This unit will automacitally MUTE the music of tuner or Media player when there is announcement from the navigation voice guidance.
Specification General Operating Voltage DC 11 -14.4V Grounding System Negative Ground Fuse: 15-Amp Mini ATM Type Operating Temperature: 0°C to 50°C Unit Mounting Angle < 30° TFT Screen Screen Size: 3.5" (Measured Diagonally) Screen Type: TFT Liquid Crystal Display active matrix Resolution: 960 (W) x 324 (H) Radio Frequency Range...
Page 76
Specification Media Player DVD / CD Compatible Disc/Format See “Disc Note” for more details description Signal to Noise Ratio > 90 dB Dynamic Range > 9 0 dB Frequency Response 20Hz to 20Khz +/-3dB Channel Separation 2 Channel (Stereo) >60dB @1khz Video Color System NTSC / PAL...
Trouble Shooting Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom Cause Solution No power The car ignition is not on. If the power supply is properly connected to the car accessory terminal, switch the ignition key to “ACC”.