4.3.22 Firewall – Virtual Server ..................59 4.3.23 Route Setup......................60 4.3.24 QoS..........................61 4.3.25 USB Storage ......................62 4.3.26 Management – Statistics ..................64 4.3.27 Management – DDNS ................... 65 USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 3
(GI)?..................83 HAT IS UARD NTERVALS CONFIGURATION EXAMPLES ................. 84 7.1. – PPP WAN................84 XAMPLE ON THE 7.2. – F WAN................88 XAMPLE IXED ON THE USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
1. INTRODUCTION The Webee Wireless N Router offers you a high-speed WiFi network and internet access via a fixed or 3G broadband modem. You can connect the router to an xDSL Modem (usually ADSL or VDSL), Cable Modem or 3G USB Modem.
DC Power Adapter Operating Temperature 0 ~ 50 C ambient temperature Storage Temperature -10 ~ 70°C ambient temperature Humidity 5 to 90 % maximum (non-condensing) Dimension 138x92x33mm USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Supports Log table and remote Log service. • Support Setup Wizard mode. • Supports Network File sharing function. • Supports FTP Server function. • Supports USB storage format tool. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Flashing Data is transmitting or receiving on the WAN interface. Port linked. No link. 5. LAN LED Flashing Data is transmitting or receiving on the LAN interface. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Support auto-sensing on 10/100M speed and half/ full duplex; comply with IEEE 802.3/ 802.3u respectively. The USB port allows USB Storage connection to support FTP server、File server. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
2.6. HARDWARE REQUIREMENTS FOR WI-FI CONNECTIVITY To use the Webee Router in a wireless local area network you will need: 1) Computer with an Ethernet interface 2) Ethernet Network Cable (RJ-45) (included in the package) to connect the router to a WAN interface.
192. 168. 1. 254 Subnet Mask 255. 255 .255. 0 IP Address Subnet Mask WLAN configuration SSID Mode Channel Number Encryption Pass phrase User name and password Name Password USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
2. Connecting the Router to a computer using a network cable Ethernet Cable Cat5, RJ-45 Webee Router 3. Wirelessly connecting the Router xDSL, Cable This installation method Modem requires expertise Internet Webee Router USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Cable modem. A straight-through Ethernet cable with appropriate cable length is needed. Step 3: Supply DC power to the Webee Router. Use only the AC/DC power adapter supplied with the router; damage may occur if using a different type of power adapter.
4. SOFTWARE CONFIGURATION There are web based management and configuration functions allowing you to have the job done easily. The Webee Router is delivered with the following factory default parameters on the Ethernet LAN interfaces. Default IP Address: 192.168.1.254 Default IP subnet mask: 255.255.255.0 WEB login User Name: <blank>...
4.3. MANAGEMENT AND CONFIGURATION ON THE ROUTER 4.3.1 Status This page shows the current status and some basic settings of the device, including system, wireless, Ethernet LAN and WAN configuration information. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 15
USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 16
It shows the default gateway setting for WAN interface outgoing data packets. MAC Address It shows the MAC address of WAN interface of the Router. WAN Link Status It shows WAN connection status. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
4.3.2 Setup Wizard This page guides you to configure the wireless broadband router for the first time USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 18
Operation Mode This page followed by Setup Wizard page to define the operation mode. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 19
This page is used to enable and configure NTP client LAN Interface Setup This page is used to configure local area network IP address and subnet mask USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 20
This page is used to configure WAN access type Wireless Basic Settings This page is used to configure basic wireless parameters like Band, Mode, Network Type SSID, Channel Number, Enable Mac Clone (Single Ethernet Client) USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 21
Wireless Security Setup This page is used to configure wireless security USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
4.3.4 Wireless - Basic Settings This page is used to configure the parameters for wireless LAN clients that may connect to your Webee Router. Here you may change wireless encryption settings as well as wireless network parameters. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1...
Page 23
Refer to 4.32 What is Modulation Coding Schemes (MCS)? Associated Clients Click the Show Active Clients button to open Active Wireless Client Table that shows the MAC address, transmit-packet, receive-packet USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
4.3.5 Wireless - Advanced Settings These settings are only for more technically advanced users who have a sufficient knowledge about wireless LAN. These settings should not be changed unless you know what effect the changes will have on your Webee Router. Item Description...
Select the encryption supported over wireless access. The encryption method can be None, WEP, WPA, WPA2 or WPA- Mixed Refer to 4.9 What is WEP? 4.15 What is Wi-Fi Protected Access (WPA)? USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Access Point. When this option is enabled, no wireless clients will be able to connect if the list contains no entries. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1...
This is a security control function; only those clients registered in the access control list can link to this Webee Router. MAC Address Fill in the MAC address of client to register this Webee Router access capability. Comment Fill in the comment tag for the registered client.
Page 28
WDS Security Setup Requirement: Set [Wireless]->[Basic Settings]->[Mode]- >AP+WDS This page is used to configure the wireless security between APs. Refer to 3.3.6 Wireless Security Setup USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 29
USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Mesh network uses wireless media to communicate with other APs, like the Ethernet does. To do this, you must set the APs in the same channel with the same Mesh ID. The APs should be under AP+MESH/MESH mode. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2...
Page 31
Mesh network. When ‘Deny Listed’ is selected, those mesh nodes in thelist will not be able to create connections. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2...
Page 32
Click the Reset button to abort change and recover the previous configuration setting. Wireless Mesh Network Information These information is only for more technically advanced users who have a sufficient knowledge about wireless mesh network. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 33
The address of the neighbor MP to that data packet for the destination should be forwarded. Portal Enable This column shows if the destination MP is a portal or not. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 34
This table shows the MAC address for each proxied wired or wireless client. Item Description Refresh Click Refresh button can refresh the current information shown in this page. Close Click Close button can close the popped-up window. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
This page allows you to change the setting for WPS (Wi-Fi Protected Setup). Using this feature could let your wireless client automically syncronize its setting and connect to the Access Point in a minute without any hassle. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2...
Page 36
Current Key Info closed. Encryption It shows the Encryption mode. Key It shows the Encryption key. Client PIN Number Fill in the Client PIN Number from your Client sites. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
4.3.13 LAN Interface Setup This page is used to configure the parameters for local area network that connects to the LAN ports of your Webee Router. Here you may change the setting for IP address, subnet mask, DHCP, etc. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1...
Page 38
Apply Changes Click the Apply Changes button to complete the new configuration setting. Reset Click the Reset button to abort change and recover the previous configuration setting. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 39
Delete All Click to delete all the registered clients from the Static DHCP list. Reset Click the Reset button to abort change and recover the previous configuration setting. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
This page is used to configure the parameters for wide area network that connects to the WAN port of your Webee Router. Here you may change the access method to Static IP, DHCP, PPPoE , PPTP L2TP or GSM 3.5G by click the item value of WAN Access Type.
Page 41
Apply Changes Click the Apply Changes button to complete the new configuration setting. Reset Click the Reset button to abort change and recover the previous configuration setting. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 42
Enable Ping Access on WAN Click the checkbox to enable WAN ICMP response. Enable Web Server Access on WAN Click the checkbox to enable web configuration from WAN USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 43
Apply Changes Click the Apply Changes button to complete the new configuration setting. Reset Click the Reset button to abort change and recover the previous configuration setting. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 44
Fill in the service name of Service Name. The default value is empty. Connection Type Select the connection type from pull-down menu. There are Continuous, Connect on Demand and Manual three types to select. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 45
Apply Changes Click the Apply Changes button to complete the new configuration setting. Reset Click the Reset button to abort change and recover the previous configuration setting. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 46
PPTP Item Description USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 47
Apply Changes Click the Apply Changes button to complete the new configuration setting. Reset Click the Reset button to abort change and recover the previous configuration setting. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 48
If you select the L2TP support on WAN interface, fill in the IP address for it. Subnet Mask If you select the L2TP support on WAN interface, fill in the USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 49
Apply Changes Click the Apply Changes button to complete the new configuration setting. Reset Click the Reset button to abort change and recover the previous configuration setting. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 50
Click to select GSM 3.5G support on WAN interface. There are 3.5G Devices, Authentication Number and APN settings need to be done. 3.5G Devices Select 3.5G device, this version supports HuaWei E220, E180, E172 and E270. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2...
Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2...
Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2...
NAT firewall. These settings are only necessary if you wish to host some sort of server like a web server or mail server on the private local network behind your Gateway's NAT firewall. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2...
Page 55
Delete All Click to delete all the registered entries from the port-forwarding list. Reset Click the Reset button to abort change and recover the previous configuration setting. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Click to delete all the registered entries from the URL Filtering list. Reset Click the Reset button to abort change and recover the previous configuration setting. 4.3.20 Firewall – DMZ USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Click the Reset button to abort change and recover the previous configuration setting. 4.3.21 Firewall – VLAN Entries in this table could configure wired or wireless VLAN settings for scalability, security and network management. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 58
WAN port. Also, when packet is come from WAN to LAN, router will forward this packet to the LAN port, with matched VID. Priority Select port priority. Click to Enable CFI. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Delete All Click to delete all the registered entries from the port-forwarding list. Reset Click the Reset button to abort change and recover the previous configuration setting. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Click to delete the selected rout table that will be removed from the static route table list. Reset Click the Reset button to abort change and recover the previous configuration setting. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Manual Downlink Speed(Kbps) Input number to set Downlink speed. Address Type Click the set type either IP or MAC address. Local IP Input the range IP address of LAN. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Click Reset button to abort change and recover the previous configuration setting. 4.3.25 USB Storage This page provides USB storage management like USB link status, network file sharing, ftp server and USB FAT32 format tool. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 63
Click drop down menu to select which USB storage which you would like to set as FTP Server. Current Share Folder It shows the current FTP USB server. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
It shows the statistic count of received packets on the wireless LAN Received Packets interface. Ethernet LAN It shows the statistic count of sent packets on the Ethernet LAN USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Apply Change Click the Apply Changes button to save and enable DDNS service. Reset Click the Reset button to abort change and recover the previous configuration setting. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Click the Apply Changes button to save and enable NTP client service. Reset Click the Reset button to abort change and recover the previous configuration setting. Refresh Click the refresh the current time shown on the screen. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
This page is used to enable and setup protection to prevent attack by hacker’s program. It provides more security for users. Item Description Enable DoS Prevention Click the checkbox to enable DoS prevention. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Input the remote log IP address Apply Changes Click the Apply Changes button to save above settings. Refresh Click the refresh the log shown on the screen. Clear Clear log display screen USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
This page allows you save current settings to a file or reload the settings from the file that was saved previously. Besides, you could reset the current configuration to factory default. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2...
Load Settings from File Click the Browse button to select the configuration files then click the Upload button to update the selected configuration to the Webee Router. Reset Settings to Default Click the Reset button to reset the configuration parameter to factory defaults.
Click the Apply Changes button to save settings. Reset Click the Reset button to abort change and recover the previous configuration setting. 4.3.34 Management – Reboot This page is used to reboot the system. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
4.3.35 Management - Password Setup This page is used to set the account to access the web server of Access Point. Empty user name and password will disable the protection. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2...
Page 74
Click the Apply Changes button to complete the new configuration setting. Reset Click the Reset button to abort change and recover the previous configuration setting. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
5. WARRANTY AND SUPPORT The Webee Router has a 2 year hardware warranty. If you encounter a hardware problem during the warranty period, please contact your reseller. For more information and support on the network services, please contact your service provider.
BSSs forming a single subnetwork. Since most corporate WLANs require access to the wired LAN for services (file servers, printers, Internet links) they will operate in infrastructure mode USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2...
6.7. WHAT ARE POTENTIAL FACTORS THAT MAY CAUSES INTERFERENCE? Factors of interference: • Obstacles: walls, ceilings, furniture… etc. • Building Materials: metal door, aluminum studs. • Electrical devices: microwaves, monitors and electrical motors. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
If you find that your corrupted packets or asymmetric packet reception (all send packets, for example). You may want to try lowering your fragmentation threshold. This will cause USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2...
SSID configured in the client must match the SSID of the access point. Some wireless devices don't work properly if SSID isn't broadcast (for example the D-link USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2...
6.19. WHAT IS ADVANCED ENCRYPTION STANDARD (AES)? Security issues are a major concern for wireless LANs, AES is the U.S. government’s next-generation cryptography algorithm, which will replace DES and 3DES. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2...
Clone MAC address is designed for your special application that request the clients to register to a server machine with one identified MAC address. Since that all the clients will communicate outside world through the Webee Router, so have the cloned MAC address set on the Webee Router will solve the issue.
6.33. WHAT IS FRAME AGGREGATION? Every 802.11 packet, no matter how small, has a fixed amount of overhead associated with it. Frame Aggregation combines multiple smaller packets together to form one larger USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2...
Support of the 400ns GI is optional for transmit and receive. The purpose of a guard interval is to introduce immunity to propagation delays, echoes, and reflections to which digital data is normally very sensitive. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2...
7.1. EXAMPLE ONE – PPPOE ON THE WAN Sales division of Company ABC likes to establish a WLAN network to support mobile communication on sales’ Notebook PCs. MIS engineer collects information and plans the Webee Router implementation by the following configuration. WAN configuration: PPPoE...
Page 85
Open LAN Interface Setup page, enter the IP Address “192.168.1.254”, Subnet Mask “255.255.255.0”, Default Gateway “0.0.0.0”, enable DHCP Server, DHCP client range “192.168.1.100” to “192.168.1.200”. Press button to confirm the configuration setting. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 86
Configure the WLAN interface: Open WLAN Interface Setup page, enter the SSID “MyWLAN”, Channel Number “11”. Press button to confirm the configuration setting. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 87
USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
7.2. EXAMPLE TWO – FIXED IP ON THE WAN Company ABC likes to establish a WLAN network to support mobile communication on all employees’ Notebook PCs. MIS engineer collects information and plans the Webee Router implementation by the following configuration.
Page 89
Open LAN Interface Setup page, enter the IP Address “192.168.1.254”, Subnet Mask “255.255.255.0”, enable DHCP Server, DHCP client range “192.168.1.100” to “192.168.1.200”. Press button to confirm the configuration setting. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Page 90
Configure the WLAN interface: Open WLAN Interface Setup page, enter the SSID “MyWLAN”, Channel Number “11”. Press button to confirm the configuration setting. USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
EN 301 489-17 V1.3.2 EN 60950-1: 2006 MPE calculation The following importer is responsible for this declaration: Daimler Finland Oy Ab Kutomotie 18 B FI-00380 Helsinki Finland Helsinki 1.6.2010 USER MANUAL OF WEBEE WIRELESS N ROUTER Version:1.1 Firmware Type 2 P/N: 60291092...
Need help?
Do you have a question about the Wireless N Router with 3G Modem Support and is the answer not in the manual?
Questions and answers