1. Manuals
  2. Brands
  3. D&R Manuals
  4. Amplifier
  5. Mic-Amp
  6. User manual

D&R Mic-Amp User Manual

D&r two channel pre-amp user manual
Hide thumbs Also See for Mic-Amp:
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
" " MIC
MIC-AMP
-AMP" "
USER
MANUAL
manual page 1

Advertisement

Table of Contents
loading

Related Manuals for D&R Mic-Amp

Summary of Contents for D&R Mic-Amp

  • Page 1 " " MIC MIC-AMP -AMP" " USER MANUAL manual page 1...
  • Page 2 Geachte klant, Wij danken u hartelijk voor uw keuze en het vertrouwen dat u in ons produkt stelt. U deed een goede keus, dit produkt is ontworpen door en voor professionele gebruikers. Er is gebruik gemaakt van onze enorme "know how" in mengtafel en signaal processor technieken en dit gekombineerd met hoogwaardige komponenten geeft u de zekerheid van een lange gebruiksduur.

  • Page 3: Rack Mounting

    RACK MOUNTING You can mount the MIC-AMP (height is 1HE, width is 9.1/2") in a 19" rack by using two MIC-AMP modules or using one MlC-AMP and one blindpanel. - Allow adequate air circulation to prevent internal heat build-up.

  • Page 4: Setting Up Procedure

    P.C.M.-units and DAT/DCC recorders SETTING UP PROCEDURE Connect the microphone to the input of the MIC-AMP and the output of the MIC-AMP to the equipment it should be connected to. GAIN When a signal at the input is present the normal led lits regularly.

  • Page 5: Specifications

    3 = out of phase pin 1 = ground The MIC-AMP has two separate, low impedance, ground compensated outputs on a nominal operating level of -10 dB and a maximum output level of +22 dBu. SPECIFICATIONS Inputs stereo jack / XLR female...
  • Page 6 Dimensions 201 x 44 x 175 mm (w/h/d) (excl. controls) 201 x 44 x 198 mm (w/h/d) (incl. controls) 9,5" x 1HE (w/h) Weight Approx. 1,7 kg CLEANING Clean the cabinet, panel and controls with a dry soft cloth. Do not use a moistened cloth or any type of solvent, such as alcohol or any other spirit, which might damage the finish.

  • Page 7: Declaration Of Conformity

    Manufacturers Name: D&R Electronica Weesp b.v. Manufacturers Address: Rijnkade 15B, 1382 GS Weesp, The Netherlands declares that the product Mic-amp conforms to the following product specifications: EMC: EN 55022: 1987 CISPR 22 (1993) class B EN 500082-1 (1992) Supplementary Information: The products herewith complies with the requirements of the EMC Directive 89/336/EEC (1989) as amended by the CE Marking Directive 93/68/EEC (1993).

  • Page 8: Product Safety

    PRODUCT SAFETY This product is manufactured with the highest standards and is double checked in our quality control department for reliability in the "HIGH VOLTAGE" section. CAUTION Never remove any panels, or open this equipment. No user servicable parts inside. Equipment power supply must be grounded at all times.
  • Page 9 Allthough removing the ground wire sometimes cures a system hum, it will create a very hazardeous situation for the performing musician. Always earth all your equipment by the grounding pin in your mains plug. Hum loops should be only cured by proper wiring and isolation input/output transformers. Replace fuses always with the same type and rating after the equipment has been turned off and unplugged.

Table of Contents