Related Manuals for IP-Cam JW0004
Summary of Contents for IP-Cam JW0004
-
Page 1: User Manual
Wireless Network IP Camera For PC View) Night Vision & Remote Operation User Manual (Applicable models: JW0004,JW0005,JW0006,JW0008,JW0011,JW0012) -
Page 2: Packing List
These are the models: Packing List Untie the pack and check the items contained against the following list: ●IP Camera X1 ●Warranty Card X1 ●DC Power Supply X1 ●CD X1 ●Certificate of Quality X1 ●Mounting bracket X1 NOTE: Please contact us immediately if anything damaged or short of contents. -
Page 3: Table Of Contents
CONTENTS 1. Product Introduction ...................3 1.1. Safety Introduction ..................3 1.2. Product Specifications..................3 1.3. System Requirements..................3 1.4. Product Views……………..........…………....4 1.4.1 Front View......................4 1.4.2 Interface View....................5 1.5. Hardware Installation..................5 1.6. Software Installation..................6 2. Software Operation....................6 2.1. Search Tool Software..................6 2.1.1. -
Page 4: Product Introduction
1. Product Introduction 1.1 Safety Instructions (1). Use the proper power source. Do not use this product with a power source that supplies more than the specified Voltage (100-240V AC). (2). Never insert anything metallic into the camera. Inserting metal object into the camera can be a source of dangerous electric shock. (3). -
Page 5: System Requirements
*-Support remote system update; *-Support DDNS analysis, support LAN & Internet (ADSL,Cable Modem) *-Support variety of network protocol: TCP/IP, UDP, SMTP, PPPoE, Dynamic DNS, DNS Client, SNTP, BOOTP, DHCP, FTP, SNMP, WIFI/802. 11b/g *-Parts of modes products support one/ two way audio, talkback; *-Support motion detection alarm function (area &... -
Page 6: Product Views
Network light: constant sparkle after power up data transmission. 4: Antenna: 5: Power input interface: connect direct current 5V Power TF Socket : Useless for JW0004. 1.5 Hardware Installation Follow the steps below to set up your camera hardware. Make sure to follow each step carefully to ensure that the camera operates properly 1. -
Page 7: Software Installation
1.6 Software Installation Figure 1.4 Open the CD Install the follow software: 1. ActiveX: Click “OCX setup”—“Next”—“Install”—“Finish”. 2. Search Tool: Open the CD, click ,The Search Tool will run automatically.( No need to install. You can copy this software to your desktop.) Figure 1.5 2. -
Page 8: Configuration Of The Network
Figure 2.1 Note: The software searches IP Servers automatically over LAN. There are 2 cases: 1. No IP Cameras found within LAN. After about 1 minute search, the Equipments List Field not show the IP address. 2. IP Cameras have been installed within LAN. All the IP Cameras will be listed and the total number is displayed in the Equipments list field as shown in Figure 2.1 Note：... -
Page 9: Real-Time Video Demonstration
IP address: Fill in the IP address assigned and make sure it is in the same subnet as the Gateway, and the subnet should be the same as your computer or router. (i.e. the first three sections are the same) Subnet Mask: The default subnet mask of the equipment is: 255.255.255.0. -
Page 10: View Via Ie Browser
Figure 3.2 (1) ActiveX Mode (For IE Browser): available in IE6.0 or above explorer (2) “RTSP Stream Mode”: available in Firefox, Safari, and Google browser. (3) “No Plug-In Mode”: available in smart phone browser. (4) SD card video playback online 3.2. - Page 11 Figure 3.3 After Download Ocx-Setup (oPlayer Software), Click and install it, untill finished. Figure 3.4...
- Page 12 Figure 3.3 Windows XP system Figure 3.4 Win7 System Note: If there is still no live video after run ActiveX, please try to enable the ActiveX options of IE security settings, please do the follow steps: 1. Close the firewall of your computer. 2.
- Page 13 Figure 3.5 Figure 3.6 In Addition: you can also click “start” menu->“Internet Explorer”, choose “Internet attributes “ to enter, or via “Control Panel” ->“Internet Explorer”, enter to Security setting. 3. If there is still no image, please close your anti-virus software, and then try step 1 & 2 again.
-
Page 14: View Via Safari, Firefox, Google Browser
Figure 3.7 NOTE: Make sure that the firewall or anti-virus software doesn’t block the software or ActiveX. If you couldn’t see live video, please close your firewall or anti-virus software, and try again. 3.3. View via Safari, Firefox, Google Browser Choose Server Push Mode (For Safari, Firefox, Google Browser), and sign in Server Push Mode doesn’t support ActiveX, so some functions are not available, such As Record, Audio, Talk, Speaker,The speed control bar, Zoom etc.),if you want to use... -
Page 15: Main Menu Interface Introduction
3.4. Main Menu interface introduction Take the “Active Mode(For IE Browser)” For example: Figure 3.8... - Page 16 The Pan/Tilt Feature only works when the cameras have this Pan/Tilt function. This option enables log detection. After the online user clicks this button, a log is entered into the camera’s Log Data documenting the IP address of users who have accessed the IP camera.
-
Page 17: Administer Setting Instruction
3.5. Administer Setting Instruction When login as Administrator, you can enter the IP Camera for Administrator. Administrator supports all the settings and operations of the camera; you can set and control it freely There are some special functions only for administrator as below: Alias setting : You can set your favorite device aliases. -
Page 18: Network Settings
Figure 3.9 Figure 3.10 Network Settings 3.5.2 Figure 3.11 This sector is for DHCP and IP configuration, port forwarding is needed, If you choose to set IP address,please fill in the relative IP address, subnet mask, gateway, DNS server, Http port;... -
Page 19: Wireless Settings
3.5.3 Wireless Settings 1. Make sure the router is a wireless router. 2. Make sure the Wi-Fi antenna installed. 3. Make sure whether there is encryption of the WLAN of the router, if there is encryption, keep the key. 4. Login the camera, click >“Wireless Lan Settings”>”Scan”, please scan 2times, then you will find the WLAN from the list, choose the one you use. - Page 20 Figure 3.13 (2): Choose the DDNS, there are 4 kinds of options: (1): Manufacturer’ DDNS: We provide a free DDNS: vipcam.org. This domain is provided by manufacturer. Note:If you find the DDNS Service blank and you want use the manufacturer’s free DDNS, Please Choose “vipcam.org”...
-
Page 21: Port Forwarding Settings
Figure 3.15 Figure 3.16 You have to register an account firstly, keep the user, password, host, then fill in it. Note: Only one DDNS can be chosen, for example, if you use manufacturer’s DDNS, the 3rd party one won’t work, if use the 3 party DDNS, the manufacturer’s one won’t work. - Page 22 Figure 3.17 Make sure the “Subnet Mask”, “Gateway”, “DNS Server” is the same as your router. 2: Port Forwarding in the router. This is the most important step. Set port forwarding in router refer to the IP of your camera correctly, then the DDNS will work.
- Page 23 Fill the service port (except 80), IP address of the camera, then click Save The port and IP address should be the same as Camera. BELKIN: (1) Login the router. Common address is http://192.168.1.1 (2) Choose “Firewall”, select “Virtual Servers” (3) Input the port (except 80) and IP address, then click save.
- Page 24 (2) Choose “Advanced”, select “Virtual Servers” (3) Input the port, IP address, Protocol, then click save. Note: The “public port” & “private port” should be the same as camera’s port, choose the protocol to be “both”. Figure 3.29 After all these 4 steps done, then you can use the DDNS freely, check the DDNS status from the camera as below, and get the link of DDNS for internet view.
-
Page 25: Ddns Register
3.5.5.3 DDNS Register For example, you can go to Dyndns website to register a free account. http://www.dyndns.org / http://www.dyndns.com. Step1: enter http://www.dyndns.com/ and Create Account Figure 3.21 Step2: Set the username and password as below: Figure 3.22... - Page 26 Step3: After a minute, you will receive a E-mail from DynDNS Support and it will give you a confirmation address (e.g. https://www.dyndns.com/confirm/create/ONMzltcCBk6mcHJI5MhVD0g) Figure 3.23 Figure 3.24 Step4: When the Account Confirmed, login and start using your account. Choose Add Host Services(Figure 3.25) and enter Add New Hostname (Figure 3.26)page. Figure 3.25...
- Page 27 Figure 3.26 Step5: On the Add New Hostname page. 1) input your Hostname. 2) choose Host with IP address 3) click Use auto detected IP address xxx.xx.xx.xxx. Then click Create Host. 4) after you have added a New Hostname , you need “Proceed to checkout” Figure 3.27...
- Page 28 Figure 3.28 Figure 3.29 Step6: Now you obtained a Dynamic Domain Name(Figure3.30),and can use it in the DDNS Service Settings(details: 3.5.5) Notice: If you have a dynamic IP address, Make sure you have download the DynDNS’s “Update Client”. And installed it succeed in your computer. Figure 3.30...
-
Page 29: Email And Ftp Service Settings
3.5.6 E-mail and FTP service Settings Figure 3.31 The above setting is a preparation for the alarm function, the sender should be entered the sender’s email address，recipient 1、2、3、4 is filled with recipient E-mail address；SMTP server should be filled with the sender email SMTP server，e.g. the sender email address is abc@163.com，and enter mail.163.com. -
Page 30: Alarm Service Settings
Figure 3.32 The above setting is equally similar to Mail Server Settings,when alarming is triggered it also sends image,please enter FTP server,FTP port,FTP user,FTP password, FTP upload directory,FTP mode,FTP mode has two options: PORT and POSV. If needs a quick upload image, then select it, edit upload image interval（second） 3.5.7. -
Page 31: Record&Capture Path
Figure3.33 3.5.8 PTZ Settings This sector is for setting the PT function (Pan&Tilt). You can also cancel self-checking function here, but you will also lose presetting bit function. PTZ speed can be adjusted here. Figure 3.11 3.5.9 Record&Capture Path This sector is for Record&Capture Path in your computer.It includes: Record&Capture Path, Record file length(MB), Record time length(Minute), Reserved disk space(MB), Record cover. -
Page 32: 1.Restore Factory Settings
Figure 3.34 Record cover means when the disk is full, the old recording files will be deleted automatically. 3.5.10 Ugrade Device Firmware In this sector, you can do following operations. Figure 3.35 3.5.10.1 Restore Factory Settings When users forget password, we can restore ex-factory settings, when click, a picture will pop up, Click ok, and wait for 1 minute and you can use it normally. -
Page 33: Record Schedule
3.5.10.3 Upgrade Firmware&WEB UI You can not upgrade your device unless you got camera problems. And upgrading is risky. Be cautious to do that. 3.5.11 Record Schedule (For JW005,JW0012, with SD card recording function) This sector is for SD card recording settings. - Page 34 You will see: 3.5.12 Back When settings are finished, click back to see camera video.
-
Page 35: Warranty
4 Warranty Under normal use condition, products resulting from its own failures in the warranty period will be free maintenance. Warranty Terms as following: a) Charge-free maintenance of the product is one year. We can repair it for free during the guarantee period (Damages not caused by misuse or vandalism). Repair over guarantee period, we will charge maintenance fee. - Page 36 We are always in service! That’s all,thank you!