Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Polk Audio Momo C400.4 Carbon Series
Summary of Contents for Polk Audio Momo C400.4 Carbon Series
- Page 1 ’ C400.4 Carbon Series 4/3/2 Channel Amplifier...
-
Page 2: Getting Started
Please inspect your new amplifier(s) carefully. Notify your Polk Audio dealer if you notice Welcome to the Polk Audio family! For over thirty years, George Klopfer and I, and all any damage or missing items. Keep the carton and packing material; this will do the best the people at Polk Audio, have been designing and building sound equipment for job of protecting your equipment if it must be transported. - Page 3 “max headroom” (!) and more power for low impedance loads. a professional installer. Your Polk Audio dealer is a good place to find one. If you intend to do the • Each model features fully adjustable electronic crossovers to power any install using any speakers installation yourself we assume you possess some skill in the proper use of hand and power tools.
- Page 4 This circuit breaker or fuse should be no greater than the fuse(s) of your amplifier for your marks more visible. optimal protection. For example, this Polk Audio Amplifier has two 30A fuses. Your “vehicle protection” fuse should be rated at 60A. See your authorized Polk AutoSound Dealer for Drill holes using a 1/8"...
-
Page 5: Typical Installation
Your amp will need to draw large levels of current, so use the largest gauge power/ground cable available; we recommend at least 8 AWG. (See your authorized Polk AutoSound Dealer for power 9. CONNECT the remote turn-on wire to the amplifier. - Page 6 Wire Routing Options For Flush Mount installations (where amp sits directly on solid surface), route wiring through side vents of end caps BEFORE wiring into the amp. For Stealth installations, route wiring down through bottom opening under removeable plate. P O L K / M O M O : C H A M P I O N S H I P P E R F O R M A N C E W W W .
- Page 7 Set the control to 80Hz – 120Hz and adjust it by ear woofer in the system. The frequencies below the crossover head unit’s owner’s manual), set this selector to HIGH See your Authorized Polk AutoSound Dealer or visit the from there. point will be attenuated at 12dB/Octave or 24/Octave.
- Page 8 P O L K / M O M O : C H A M P I O N S H I P P E R F O R M A N C E W W W . P O L K A U D I O . C O M / A M P S...
- Page 9 P O L K / M O M O : C H A M P I O N S H I P P E R F O R M A N C E W W W . P O L K A U D I O . C O M / A M P S...
-
Page 10: Power Connection Details
Power Connection Details Sketch Your Custom Install Configuration for Future Reference Here: Before installing your amplifier, disconnect the negative (ground) wire from the vehicle’s battery and secure it away from the battery. This will prevent accidental damage to the system. And to yourself as well. -
Page 11: Protect Your Hearing
Protect Your Hearing! Power Output: ...........RMS Continuous Power Now that you’ve got Polk Audio equipment in your car you’re a valued member of the Polk Audio (at 14.4V at the input terminals, 20Hz - 20kHz) family. We want you, and your hearing, to be around for a long, long time. We urge you to practice Per Channel into 4 Ohms (0.1% THD+N) ..75W... - Page 12 AMPLIFIER OR OTHER ment as provided above. In no event will Polk Audio, Inc. be ELECTRONIC COMPONENT will be free from defects in liable to you for any incidental or consequential damages...
- Page 13 Outside the US, call 410-358-3600. “Polk,” “Polk Audio,” “The Speaker Specialists” and “Dynamic Balance” are registered trademarks of Polk Investment Corporation used under license by Polk Audio Incorporated. “MOMO” is a registered trademark of MOMO Design, Italy.