Vibration Alarm; Sos Alarm; Geo-Fence - Elmic GT03B User Manual

5. Vibration alarm

When the device is in arm state, vibration will activate alarms. The device will send vibration alarm to the SOS numbers in
10s.
If the GPS is located, the device will send accurate address information. If GPS is not located, the device will send LBS
address information. If GPS is located in 5 minutes, the device will send accurate address information.
Example of GPS address information:
"vibration alarm: Bao'an Road, Bao'an District, Shenzhen, Guangdong (N22.57139,E113.87710)
Example of LBS address information:
"vibration alarm: nearby Bao'an Road Bao'an District, Shenzhen, Guangdong (22.571,113.876)".
When vibration alarm is actived, if GPS is located successfully while there is no GPRS connection, the device will send
longitude and latitude location to SOS numbers pre-set : " Vibration alarm! Location: N23.111748, E114,409215,
Date&Time: 11-04-28 10:00:48".
When vibration alarm is actived, if GPS is not located successfully and there is no GPRS connection, then device will not get
location information and send to SOS numbers pre-set :"Vibration alarm! Please notice".
Remark：The interval of vibration alarm could not be less than 5 minutes.

6. SOS alarm

Press SOS button for more than 3s to activate SOS alarm, meanwhile you could feel the vibration, and then the device will
send an address information message to the SOS number. If GPS is located, the device will send an accurate address
information,
e.g.: "Emergency call(LBS): Bao'an Road, Bao'an District, Shenzhen, Guangdong (N22.57139,E113.87710)".
If GPS is not located, the device will send a LBS location information:
e.g.:"Emergency call(LBS): nearby Bao'an Road Bao'an District, Shenzhen, Guangdong (22.571,113.876)".
Then it will dial the SOS numbers by cycle, if any SOS number answer the call, it will stop calling. If there's no response
after all the number been dialed for three cycles, it will stop.

7. Geo-fence

You can set a designated area as geo-fence. When the device gets in/out of this area, it will send alarm to SOS numbers
when the geo-fence function is ON.
i. Turn on geo-fence
Geo-fence function is off as default. You can turn on geo-fence via SMS command.
Circular fence
You can set a coordinate as the centre of the circular fence and set the radius
Go in fence SMS command:
e.g.: FENCE,ON,0,N22.57139,E113.87710,5,IN#
It means the radius is 500 meters.（radius 1=100M，2=200M····and so on）
The device will reply"OK"if set successfully. When the device is in this circular area, it will send alarm
to the SOS numbers.
Go out fence SMS: "FENCE,ON,0,latitude,longitude,radius,OUT#"to open circular fence function
e.g.: FENCE,ON,0, N22.57139,E113.87710,5,OUT #
It means the radius is 500 meters.（radius 1=100M，2=200M····and so on）
The device will reply"OK"if set successfully. When the device is out of this circular area, it will send alarm
to the SOS numbers.
Go in/out fence SMS: "FENCE,ON,0,latitude,longitude,radius#"
e.g.: FENCE,ON,0,N22.57139,E113.87710,5#
It means the radius is 500 meters（radius 1=100M，2=200M····and so on）
The device will reply"OK"if set successfully. As long as the device goes in or out of this circular area, it will send alarm to
the SOS numbers.
You can also set current location coordinates as the centre of the circular fence, SMS:
"FENCE,ON,0,0,0,radius#" (This SMS is only available when device get located)
ii. Disable Geo fence
If don't need geo fence function, send SMS to disable it:
After get reply "OK", geo fence function is off.
Strona 7 z 10 rev. 1.0.1
USER MANUAL:
"FENCE,ON,0,latitude,longitude,radius,IN#"
GT03B
to open circular fence function
FENCE,OFF#
GPS PORTABLE TRACKER
www.elmic.pl, elmic@elmic.pl