Conexión - Whirlpool WF5000 Installation, Use And Care Manual

G lass lid
S ome models have a top glass lid. The glass lid is made of tempered glass and even
w hen it is resistant; it should be handled with care to avoid breakings. Open and close
it without striking it, do not let it fall down before reaching its horizontal position.
Assure that the surface burners are all turned off and cooled down
never turn on the surface burners when the glass lid is dow
place hot cookware on top of the glass lid.
Oven racks
The oven cavity has 3 different heights for the racks position; thes
stop position to avoid them from falling down of the range when pu
To change the oven rack position, follow the next steps:
1. Pull the oven rack out to the stop position.
2. Raise the front edge.
3. Lift it out to release it.
4. Select the new height.
5. Place the oven rack horizontal and push it to
the stop position.
6. Raise the front edge.
7. Push again until it reaches the final position.
Broiler
The range is equipped with a broiler below the oven
door. Before using it, place the broiler tray on the 2 pins,
as shown in the pictures below. For the broil feature to
work, the oven burner should be turned on according to
the instructions for thermocontrol or thermostat.
When the oven burner is lit, turn the "Oven control"
knob to its maximum flame, which is:
-
-
Oven light
The range has an oven light bulb, this light is important to check for baking
performance without opening the oven door.
The light inside the oven cavity turns on when the switch next to the most
left hand knob is pushed downward; it is identified with this symbol. To
turn it off, the switch needs to be pushed again.
If the bulb does not work, replace it by following this sequence:
1. Unplug the range from the electrical wall outlet.
2. Remove the bulb twisting it counterclockwise.
3. Place a new 40 Watts bulb, designed for home appliances.
4. Plug the power cord of the range into the electrical wall outlet.
30
before closing it and
n. Do not
e ones also have a
lled out.
Position 5 for thermocontrol models
Position 260°C for thermostat models
C
ONEXIÓN
Conexión de la estufa a la línea de gas
1. Para conectar su estufa utilice el material especificado en la figura de abajo:
2. Verifique que no existan fugas vertiendo espuma de jabón en las conexiones y
curvas de los tubos.
Recomendaciones:
•
Si la instalación no es nueva, limpie los tubos para evitar que se tapen las
espreas o los pilotos.
•
Con el fin de facilitar el movimiento del aparato, el instalador debe hacer una
espiral con el tubo flexible de cobre e instalar una llave de paso en la línea de
suministro de gas. Esta llave debe estar fuera de la estufa y accesible a las
personas que la usan.
IMPORTANTE
•
Esta estufa está preparada para funcionar con gas LP de tanque móvil o
estacionario.
•
Para usarse con gas Natural (tubería) debe llamar a Whirlpool Service para
cambiar las espreas y hacer los ajustes necesarios. El número telefónico aparece
en la página 19. El técnico calificado debe cerciorarse que la conexión no tiene
fugas y que la presión de gas en la estufa es la que aparece en las tablas
siguientes:
GAS LP PRESIÓN DE OPERACIÓN
2,75 kPa (28 cm Col. agua)
QUEMADOR
SUPERIOR ESTÁNDAR ALUMINIO
SUPERIOR SÚPER ALUMINIO
SUPERIOR CENTRAL ALUMINIO
HORNO
DIAM CAPACIDAD
ESPREA
ESPREA TÉRMICA
NÚMERO mm kJ/h
78 0,78 7 000
86 0,86 7 500
80 0,80 7 900
57 1,092 13 600
7