COLOR TELEVISION/ VIDEO CASSETTE RECORDER/ DVD VIDEO PLAYER MW14F52 The above model is classified as a green product (*1), as indicated by the underlined serial number. This Service Manual describes replacement parts for the green product. When repairing this green product, use the part(s) described in this manual and lead-free solder (*2).
Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any marketing of new products containing the restricted substances. Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities.
CAUTION THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS SERVICE MANUAL CARE- FULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE. USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS LASER RADIATION EXPOSURE.
SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
IMPORTANT SAFEGUARDS READ INSTRUCTIONS All the safety and operating instructions should be read before the unit is operated. RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference. HEED WARNINGS All warnings on the unit and in the operating instructions should be adhered to. FOLLOW INSTRUCTIONS All operating and use instructions should be followed.
Page 6
IMPORTANT SAFEGUARDS (CONTINUED) OUTDOOR ANTENNA GROUNDING If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
Page 7
IMPORTANT SAFEGUARDS (CONTINUED) EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING NEC-NATIONAL ELECTRICAL CODE ELECTRODE SYSTEM (NEC ART 250, PART H) S2898A...
WHEN REPLACING DVD DECK [ When removing the DVD Deck ] Before removing Pick Up PCB and DVD MT PCB connector, the short circuit the position shown in Fig. 1 using a soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged. [ When installing the DVD Deck ] Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD MT PCB connector.
TAPE REMOVAL METHOD AT NO POWER SUPPLY Remove the TV/DVD/VCR block from the main unit as shown in Fig. 1 below can be seen. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.) Remove the screw 1 of the Deck Chassis and remove the Loading Motor. Rotate the Pinch Roller Cam in the direction of the arrow by hand to slacken the Video Tape.
PARENTAL CONTROL - RATING LEVEL 4 DIGIT PASSWORD CANCELLATION If the stored 4 digit password in the Rating Level menu needs to be cancelled, please follow the steps below. Turn Unit ON. Set the DVD Mode. Confirm that the 'No Disc' will be appeared on the screen. Press and hold the '7' key on the remote control unit.
TABLE OF CONTENTS GREEN PRODUCT PROCUREMENT ..................A1-1 LEAD-FREE SOLDER ......................A1-1 CAUTION ..........................A1-2 SERVICING NOTICES ON CHECKING .................. A1-3 HOW TO ORDER PARTS ....................... A1-3 IMPORTANT SAFEGUARDS ....................A1-4~A1-6 WHEN PERLACING DVD DECK .................... A1-7 TAPE REMOVAL METHOD AT NO POWER SUPPLY ............A1-8 DISC REMOVAL METHOD AT NO POWER SUPPLY ............
GENERAL SPECIFICATIONS CRT Size / Visual Size 14 inch / 357.0 mmV System CRT Type Flat Magnetic Field BV/BH +0.45G / 0.18G Color System NTSC Speaker 2 Speaker Position Front Size 2.0 x 4.7 Inch Impedance 8 ohm Sound Output 1.5W + 1.5W 10%(Typical) System...
Page 13
GENERAL SPECIFICATIONS Signal Video Signal Input Level 1 V p-p/75 ohm Output Level S/N Ratio (Weighted) at DVD Mode S/N Ratio (Weighted) at VCR Mode Horizontal Resolution at DVD Mode Horizontal Resolution at VCR(SP)Mode 220 Lines RGB Signal Output Level Audio Signal Input Level -8.0dBm/50k ohm...
Page 14
GENERAL SPECIFICATIONS G-12 Remote Unit RC-KH Control Glow in Dark Remocon Unit Remocon Format TOSHIBA Format TOSHIBA Custom Code 40-BFh, 44-BBh, 45-Bah Power Source Voltage(D.C) UM size x pcs UM-4 x 2 pcs Total Keys Keys TV/VCR Power Channel- Channel+...
Page 15
GENERAL SPECIFICATIONS G-13 Features Auto Head Cleaning (TV/VCR) VIDEO PLUS+(SHOWVIEW,G-CODE) Auto Clock Auto Setup Forward / Reverse Picture Search Auto CH Memory Closed Caption TV Auto Shut off Function End Call Index Search SQPB CABLE CM Skip(30sec x 6 Times) Comb Filter (2Lines) VM Circuit TV Monitor...
Page 16
GENERAL SPECIFICATIONS G-14 Accessories Owner's Manual Language English w/Guarantee Card Remote Control Unit Battery UM size x pcs UM-4 x 2 pcs OEM Brand Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer 300 ohm to 75 ohm Antenna Adapter Antenna Change Plug DC Car Cord (Center+) AC Plug Adapter...
Page 17
1 Corner / 3 Edges / 6 Surfaces Height (cm) Container Stuffing(40' container) Sets G-19 Material Cabinet Front 94V0 DECABROM Rear 94V0 DECABROM Non-Halogen Demand Eyelet Demand G-20 Environment Environmental standard requirement (by buyer) Green procurement of TOSHIBA Pb-free Phase3(Phase3A) Measures for Whisker A3-6...
DISASSEMBLY INSTRUCTIONS 1-3: TV/DVD/VCR BLOCK (Refer to Fig. 1-3) 1. REMOVAL OF MECHANICAL PARTS Remove the 2 screws 1. AND P.C. BOARDS Disconnect the following connectors: 1-1: BACK CABINET (Refer to Fig. 1-1) (CP351, CP353, CP402 and CP1702). Remove the 4 screws 1. Remove the TV/DVD/VCR Block in the direction of arrow.
Page 19
DISASSEMBLY INSTRUCTIONS 1-5: TOP SHIELD (Refer to Fig. 1-5) 1-7: DVD MT PCB/DVD DECK (Refer to Fig. 1-7) Remove the 11 screws 1. Short circuit the position shown in Fig. 1-7 using a Remove the screw 2. soldering iron. If you remove the DVD Deck with no Remove the Top Shield in the direction of arrow.
Page 20
DISASSEMBLY INSTRUCTIONS 1-8: VCR DECK (Refer to Fig. 1-8) 1-9: VCR MT PCB (Refer to Fig. 1-9) Remove the screw 1. NOTE Remove the 3 screws 2. Do not remove the cable at the FE Head section. The FE Remove the AV Jack Shield. Head may be damaged if you remove the cable by force.
DISASSEMBLY INSTRUCTIONS 2-3: LINK UNIT (Refer to Fig. 2-3) 2. REMOVAL OF VCR DECK PARTS Set the Link Unit to the Eject position. 2-1: TOP BRACKET (Refer to Fig. 2-1) Unlock the support 1. Extend the 2 supports 1. Remove the (A) side of the Link Unit first, then remove Slide the 2 supports 2 and remove the Top Bracket.
Page 22
DISASSEMBLY INSTRUCTIONS 2-5: LOADING MOTOR/WORM (Refer to Fig. 2-5-A) 2-6: TENSION ASS’Y (Refer to Fig. 2-6-B) Remove the screw 1. Turn the Pinch Roller Cam clockwise so that the Tension Remove the Loading Motor. Holder hook is set to the position of Fig. 2-6-A to move Remove the Worm.
Page 23
DISASSEMBLY INSTRUCTIONS NOTE [OK] Tension Connect Take care not to damage the gears of the S Reel and T Reel. Tension Band The Polyslider Washer may on the back of the reel. Take care not to damage the shaft. [NG] Tension Connect Tension Band Do not touch section “A”...
Page 24
DISASSEMBLY INSTRUCTIONS 2-9: CASSETTE OPENER/PINCH ROLLER BLOCK/P5 ARM ASS’Y (Refer to Fig. 2-9-A) Unlock the support 1 and remove the Cassette Opener. Remove the Pinch Roller Block and P5 Arm Ass’y. Cassette Opener Spring Position Fig. 2-10-B Pinch Roller Block 2-11: FE HEAD (RECORDER ONLY) (Refer to Fig.
Page 25
DISASSEMBLY INSTRUCTIONS 2-13: CAPSTAN DD UNIT (Refer to Fig. 2-13) NOTE 1. In case of the Pinch Roller Cam and Main Cam installa- Remove the Capstan Belt. Remove the screw 1. tion, install them as shown in the circled section of Fig. 2- 14-B so that the markers meet.
Page 26
DISASSEMBLY INSTRUCTIONS NOTE 2-17: CASSETTE GUIDE POST/INCLINED BASE S/T UNIT/P4 CAP/LED REFLECTOR 1. When you install the Loading Arm S Unit, Loading Arm T (Refer to Fig. 2-17-A) Unit and Main Loading Gear, align each marker. (Refer to Fig. 2-15-B) Remove the P4 Cap.
DISASSEMBLY INSTRUCTIONS 3. REMOVAL OF DVD DECK PARTS NOTE 1. Do not disassemble the DVD DECK PARTS except listed parts here. Minute adjustments are needed if the Main Frame Ass'y disassemble is done. If the repair is needed except listed parts, replace the DVD MECHA ASS'Y.
Page 28
DISASSEMBLY INSTRUCTIONS 3-3: LOADING MOTOR PCB ASS'Y/ LOADING BELT (Refer to Fig. 3-3-A) Pulley Gear Rack Loading Remove the Loading Belt. Remove the screw 1. Main Gear Remove the 2 screws 2. Remove the Loading Motor PCB Ass'y. Main Frame Ass’y Remove the Pulley Gear.
Page 29
DISASSEMBLY INSTRUCTIONS 3-6: TRAVERSE HOLDER/INSULATOR (F)/INSULATOR NOTE (R) (Refer to Fig. 3-6-A) When pushing the Rack Feed in the direction of the Remove the Traverse Holder. arrow, it should be restored to the original position by the Remove the 2 Insulator (F). spring force.
Page 30
DISASSEMBLY INSTRUCTIONS 3-8: FFC WIRE HANDLING When installing the FFC, fold it correctly and install it as shown from Fig. 3-8-A to Fig. 3-8-C. NOTE Do not make the folding lines except the specified positions for the FFC. [ 24 pin FFC ] Pick Up Side 54 ±...
DISASSEMBLY INSTRUCTIONS 4. REMOVAL OF ANODE CAP 3. After one side is removed, pull in the opposite direction to remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
DISASSEMBLY INSTRUCTIONS 5. REMOVAL AND INSTALLATION OF FLAT 3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using PACKAGE IC a tweezers and remove the IC by moving with the IC REMOVAL desoldering machine.
Page 33
DISASSEMBLY INSTRUCTIONS INSTALLATION 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin- 1. Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 5-8.) new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
KEY TO ABBREVIATIONS Audio/Control H.SW Head Switch Automatic Color Control Hertz Audio Erase Integrated Circuit Automatic Frequency Control Intermediate Frequency Automatic Fine Tuning Indicator AFT DET Automatic Fine Tuning Detect Inverter Automatic Gain Control Killer Amplifier Left Antenna Light Emitting Diode A.PB Audio Playback LIMIT AMP...
Page 35
KEY TO ABBREVIATIONS SYNC Synchronization SYNC SEP Sync Separator, Separation Transistor TRAC Tracking TRICK PB Trick Playback Test Point UNREG Unregulated Volt Voltage Controlled Oscillator Video Intermediate Frequency Vertical Pulse, Voltage Display V.PB Video Playback Variable Resistor V.REC Video Recording Visual Search Fast Forward Visual Search Rewind Voltage Super Source...
SERVICE MODE LIST This unit is provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit or on the main unit and on the remote control for more than the standard time (second).
PREVENTIVE CHECKS AND SERVICE INTERVALS The following standard table depends on environmental conditions and usage. Parts replacing time does not mean the life span for individual parts. Also, long term storage or misuse may cause transformation and aging of rubber parts. The following list means standard hours, so the checking hours depends on the conditions.
Page 38
PREVENTIVE CHECKS AND SERVICE INTERVALS CLEANING NOTE 2. TAPE RUNNING SYSTEM After cleaning the heads with isopropyl alcohol, do not When cleaning the tape transport system, use run a tape until the heads dry completely. If the heads gauze moistened with isopropyl alcohol. are not completely dry and alcohol gets on the tape, 3.
WHEN REPLACING EEPROM (MEMORY) IC If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. NOTE: No need to set data for the position of the "@" due to the adjustment value. @@ @@ Table 1 Turn on the POWER, and set to the TV mode.
MECHANICAL ADJUSTMENTS 1-2: CONFIRMATION AND ADJUSTMENT OF TENSION 1. CONFIRMATION AND ADJUSTMENT POST POSITION Read the following NOTES before starting work. Set to the PLAY mode. • Place an object which weighs between 450g~500g on the Adjust the adjusting section for the Tension Arm position Cassette Tape to keep it steady when you want to make so that the Tension Arm top is within the standard line of the tape run without the Cassette Holder.
Page 42
MECHANICAL ADJUSTMENTS 1-4: CONFIRMATION OF VSR TORQUE NOTE Install the Torque Gauge (JG002F) and Adapter (JG002B) If the torque is out of the range, replace the following parts. on the S Reel. Set to the Picture Search (Rewind) mode. Check item Replacement Part (Refer to Fig.1-4-B) Then, confirm that it indicates 120~180gf•cm.
Page 43
MECHANICAL ADJUSTMENTS 2-2: CONFIRMATION AND ADJUSTMENT OF AUDIO/ 2-3: TAPE RUNNING ADJUSTMENT CONTROL HEAD (X VALUE ADJUSTMENT) When the Tape Running Mechanism does not work well, Confirm and adjust the height of the Reel Disk. adjust the following items. (Refer to item 1-1) Confirm and adjust the position of the Tension Post.
Page 44
MECHANICAL ADJUSTMENTS 3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE 1. Tension Connect P4 Post 2. Tension Arm T Brake Spring 3. Guide Roller T Reel 4. Audio/Control Head S Reel 5. X value adjustment driver hole Adjusting section for the Tension Arm position D2-4...
ELECTRICAL ADJUSTMENTS BEFORE MAKING ELECTRICAL FUNCTION FUNCTION OSD H CONT MAX ADJUSTMENTS OSD C CONT MIN COL CENT Read and perform these adjustments when repairing the H.POSI COL. MAX circuits or replacing electrical parts or PCB assemblies. H.BLK L COL. MIN H.BLK R TINT CAUTION...
Page 46
ELECTRICAL ADJUSTMENTS (TV SECTION) 2-7: VERTICAL POSITION Receive the monoscope pattern. 2-2: CONSTANT VOLTAGE Using the remote control, set the brightness and contrast Place the set in AV MODE without signal. to normal position. Using the remote control, set the brightness and contrast to Activate the adjustment mode display of Fig.
Page 47
ELECTRICAL ADJUSTMENTS 00 OSD H "A" Fig. 2-3 Fig. 2-4 2-11: BRIGHT CENTER Receive the monoscope pattern. (RF Input) 2-13: COLOR CENTER Using the remote control, set the brightness and contrast Receive the color bar pattern. (RF Input) to normal position. Using the remote control, set the brightness, contrast, Activate the adjustment mode display of Fig.
ELECTRICAL ADJUSTMENTS 2-14: CONTRAST MAX Activate the adjustment mode display of Fig. 1-1 and press the channel button (21) on the remote control to select "CONT MAX". Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "79". Receive a broadcast and check if the picture is normal.
ELECTRICAL ADJUSTMENTS PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator. minutes before performing the following adjustments.
PRINTED CIRCUIT BOARDS TV MT/CRT SOLDER SIDE CD401 CP001 CP820 D416 HS1701 CAUTION Q1705 VR401 R1721 W804 VR1701 FOR SERVICE INFORMATION ABOUT CRITICAL R1724 D408 R445 W006 COMPONENTS, SEE INSIDE BACK COVER. R442 W851 CP852A C1711 R444 TP403 TP402 D1728 W021 W809 W806...
Page 65
PRINTED CIRCUIT BOARDS LOADING MOTOR (INSERTED PARTS) LOADING MOTOR (CHIP MOUNTED PARTS) SOLDER SIDE SOLDER SIDE CD2302 SOLDER SIDE D D0 0 CD2301 M2601 M2602 F-10...
POWER SCHEMATIC DIAGRAM (TV MT PCB) CAUTION :FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE 6.3A 125V(F1701). 6.3A 125V ATTENTION :POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME TYPE 6.3A 125V(F1701). D1706 SP353 CP353...
Page 81
LOADING MOTOR/SW SCHEMATIC DIAGRAM (LOADING MOTOR PCB) (SW PCB) SSS-13-2 CD2302 2H052601 ESE22MH24 CD2301 SW-2(CLOSE) 2H062102 GND(SW) GND(SW) SW-1(OPEN) PICK UP INNER LIMIT SWITCH LOADING MOTOR(+) FEED MOTOR (-) M2602 LOADING MOTOR(-) BCZ3B03 FEED MOTOR (+) M2603 SPINDLE MOTOR (-) BCZ3B52 SPINDLE MOTOR (+) M2601...
WAVEFORMS MPEG/MICON/DSP AUDIO/VIDEO Y/C/AUDIO/HEAD AMP 20µs 10ns 500µs 1.0V 100mV 500mV REC/PB 200ms 100mV 500µs 500mV 20mV 20ns 10µs 200mV 1.0V 100mV 200mV 200ns 100µs 1.0V 200mV MEMORY 20µs 10µs 500mV 200mV NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
Page 84
WAVEFORMS MICON 20ms 20µs 20µs 2.0V 0.5V 1.0V POWER ON POWER ON 20µs 10ms 2.0V 0.5V 1.0V POWER ON POWER ON 0.5µs 50µs 50µs 100mV 2.0V 0.5V POWER ON POWER ON POWER ON 20µs 50µs 10ms 1.0V 2.0V 2.0V POWER ON POWER ON POWER ON CHROMA/IF...
Page 85
WAVEFORMS 20µs 10ms 10ms 1.0V 10.0V POWER ON TV POWER DVD IN/OUT 20µs 50µs 2.0V POWER ON DVD PLAY POWER ON 50µs 5.0V 2.0V POWER ON DVD PLAY DEFLECTION 10ms 20µs 0.5V 200V POWER ON POWER ON 20µs 10ms POWER ON POWER ON NOTE: The following waveforms were measured at the point of the corresponding...
CHASSIS EXPLODED VIEW (TOP VIEW) CD1501 M2003 UN4001 H5002 H5001 CD1502 M101 NOTE: Applying positions AA for the grease are displayed for this section. CLASS MARK Check if the correct grease is applied for each position. GREASE I2-1...
Page 90
CHASSIS EXPLODED VIEW (BOTTOM VIEW) M2001 CD1501 CD1502 NOTE: Applying positions AA for the grease are displayed for this section. CLASS MARK Check if the correct grease is applied for each position. GREASE I2-2...
DVD DECK EXPLODED VIEW Cannot supply separately. If the repair is needed, replace the LOADER SUB ASS'Y. M2603 PCB610 (LOADING MOTOR PCB ASS'Y) CD2302 CD2301 PCB640 CD2001 (SW PCB ASS'Y) Do not replace the parts. Because, minute adjustments are needed if this condition is disassembled further more.