Husqvarna 128C Operator's Manual
Husqvarna trimmer operator's manual
Hide thumbs
Also See for 128C:
- Manual (24 pages) ,
- Operator's manual (71 pages) ,
- Operator's manual (504 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Husqvarna 128C
Summary of Contents for Husqvarna 128C
- Page 1 EN (2-22) FR (23-43) ES (44-64)
-
Page 2: Key To Symbols Symbols
This product is in accordance with applicable EC directives. 545196741 Rev. 2 4/30/09 Only intended for trimmer heads. Noise emission to the environment according to the European Community’s Directive. The machine’s emission is specified in the Technical data section and on label. -
Page 3: Table Of Contents
545196741 Rev. 2 4/30/09 Note the following before starting: Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Long- -term exposure to noise can result in permanent hearing impairment. -
Page 4: What Is What
6. Loop handle 16. Handle adjustment 7. Throttle control 17. Drive disc 8. Stop switch 18. Operator’s manual 9. Throttle lock- -out 19. Wrench (Model 128C only) 10.Cylinder cover 20. Hex wrench (Model 128L only) 545196741 Rev. 2 4/30/09 English--- 4... -
Page 5: General Safety Precautions
Personal protective equipment IMPORTANT! Whenever you use a clear- ing saw, brushcutter or trimmer you must wear personal protective equipment that is approved by the authorities. Personal protective equipment does not eliminate... -
Page 6: Machine's Safety Equipment
GENERAL SAFETY PRECAUTIONS Machine’s safety equipment This section describes the machine’s safe- ty equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the “What is what” section to locate where this equipment is positioned on your machine. - Page 7 See the section on “Technical data”. If an incorrect or faulty guard is fitted this can cause serious personal injury. Use of incorrectly wound trimmer line or an incorrect cutting attachment increases the level of vibration. WARNING: Overexposure to...
-
Page 8: Cutting Equipment
S The length of the trimmer line is also im- portant. A longer trimmer line requires greater engine power than a shorter trimmer line of the same diameter. -
Page 9: Assembly
S Insert hex wrench (C) in the hole to lock the shaft. S Screw on the trimmer head (H) in the op- posite direction to the direction of rota- tion. S To dismantle, follow the instructions in the reverse order. -
Page 10: Fuel Handling
HUSQVARNA two- -stroke oil, which is specially formulated for our two- -stroke engines. Mixture 1:50 (2%). S If HUSQVARNA two- -stroke oil is not avail- able, you may use another two-stroke oil of good quality that is intended for air cooled engines. -
Page 11: Fuelling
FUEL HANDLING Mixing S Always mix the petrol and oil in a clean container intended for fuel. S Always start by flling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. -
Page 12: Starting And Stopping
(CAUTION! Not with your foot). Then grip the starter handle with your right hand and pull the starter cord. S Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked. - Page 13 STARTING AND STOPPING NOTE: If engine dies, return blue engine choke lever to the closed position and repeat starting steps. CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine.
-
Page 14: Working Techniques
Grass trimming with a trimmer head Trimming S Hold the trimmer head just above the ground at an angle. It is the end of the trimmer line that does the work. Let the trimmer line work at its own pace. Never press the trimmer line into the area to be cut. - Page 15 S Do not allow the trimmer head to con- - stantly come into contact with the ground during normal cutting. Constant contact of this type can cause damage and wear to the trimmer head.
-
Page 16: Maintenance
Carburetor Your Husqvarna product has been designed and manufactured to specifications that re- duce harmful emissions. After the engine has used 8- -10 tanks of fuel, the engine will be run- -in. -
Page 17: Spark Plug
However, be- fore using the machine you should check that the bevel gear is filled three- -quarters full with grease. Use HUSQVARNA special grease. The grease in the bevel gear does not nor- mally need to be changed except if repairs are carried out. -
Page 18: Maintenance Schedule
Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked. Check that the trimmer head is undamaged and not cracked. Replace the trimmer head if necessary. Check that nuts and screws are tight. -
Page 19: Technical Data
NOTE! Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. Model 128C (3/8 RH arbor shaft thread) Approved accessories Type Trimmer head... -
Page 20: Ec- -Declaration Of Conformity (Applies To Europe Only)
We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46- -36- -146000, as authorised representative in the Community, declare that the grass trimmer model Husqvarna 128C/128L from serial numbers 2009- -031N00001 and onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVES:... -
Page 21: Head Line Loading
Trimmer Head Line Loading Instructions 545196741 Rev. 2 4/30/09 English--- 21... - Page 22 Plastic Blades (Tri Cut) 545196741 Rev. 2 4/30/09 English--- 22...