Advertisement
Using your tripod
1 Open the flip-lever leg
locks on each leg. Open
the leg sections from the
lock
top down (thickest section
first) to reach desired
length. Adjusting the
thickest sections first gives
your tripod more stability
and support.
2 Close the leg locks to lock
each leg at the selected
length.
Caution: Incorrectly
securing a leg lock can cause the tripod leg to retract
unexpectedly and could result in damage to the tripod or
equipment mounted on the tripod.
3 Loosen the locking collar, then spread the legs to the preset
angle. Set the tripod on a firm surface. Tighten the locking collar
to stabilize your tripod. (Close the tripod by loosening the locking
collar and pushing in on any leg.)
4 Adjust the height of the center
column by releasing the center
column locking knob (A), raising
the center column (B) to the
desired height, then tightening
the center column locking knob.
Caution: Do not raise the center
column over the safety line.
5 Hold the quick-release plate
locking lever (A) open, then lift the
mounting plate (B) to remove it.
6 Align the bottom of your camera
or camcorder with the 1/4"
mounting screw and indexing pin
(if necessary) on the plate, then
secure your camera or camcorder
to the plate with the screw. The
screw should be tight. The
indexing pin retracts if it is not
required.
7 Open the quick-release plate
locking lever and mount the plate
onto the tripod head. Push the
lever until it stops to secure the
plate.
8 To adjust vertical tilt, loosen the
vertical tilt knob, then rotate the
plate up to 90 degrees and tighten
the knob.
9 To adjust horizontal tilt, rotate the
horizontal tilt lock handle
counter-clockwise, tilt the plate as
desired, and tighten the handle.
10 To pan, turn the pan locking knob
counter-clockwise, pan the tripod
head as desired, then tighten to
lock in place.
Note: For maximum stability,
always make sure your camera
lens is over a leg.
Using your monopod
1 Release the center column locking knob, then
remove the center column from the tripod base.
loosen
2 Unscrew the leg locks and extend the leg to the
desired length. Open the leg sections from the top
down (thickest section first) to reach the desired
height. Adjusting the thickest leg sections first gives
your monopod more stability and support.
3 Tighten the leg locks to lock the monopod at the
desired height.
Unscrew leg locks from down to top
(rubber foot A - smaller leg lock B - bigger leg lock C)
to fold monopod leg sections.
Caution: Incorrectly securing a leg lock can cause the
monopod leg to retract unexpectedly and could
result in damage to the monopod or equipment
mounted on the monopod.
4 Hold the quick-release plate locking lever (A) open,
then lift the mounting plate (B) to remove it.
5 Align the bottom of your camera or camcorder with the 1/4"
mounting screw and indexing pin (if necessary) on the plate,
then secure your camera or camcorder to the plate with the
screw. The screw should be tight. The indexing pin retracts if it is
not required.
6 Open the quick-release plate locking lever and mount the plate
onto the monopod head. Push the lever until it stops to secure
the plate.
7 To adjust vertical tilt, loosen the vertical tilt knob, then rotate the
plate up to 90 degrees and tighten the knob.
8 To adjust horizontal tilt, rotate the horizontal tilt lock handle
counter-clockwise, tilt the monopod as desired, and tighten the
handle.
9 To pan, turn the pan locking knob counter-clockwise, pan the
monopod head as desired, then tighten to lock in place.
90°
Important safety instructions
• Make sure that all levers, handles, knobs, and leg locks are
correctly tightened, and that all three legs are fully opened
before use.
• Do not carry or transport the tripod with camera equipment
attached (for example, over your shoulder or cradled in your
arms).
• Do not store or expose your tripod to excessive heat or cold, or
use near any flame or fire.
• Do not oil or grease any part of the tripod.
• Do not use any solvents or thinners to clean your tripod.
• Use only a mild detergent and wipe dry with only a soft, lint-free
cloth.
• Do not exceed the load limit of this product. Load limit is 11 lbs.
(5 kg).
Specifications
Tripod
Monopod
Folded height: 27.8 in (70.5 cm)
Max height: 62.8 in (159.5 cm)
Max height: 72 in (182.50 cm)
Min height: 22.6 in (57.5 cm)
Min height: 26.7 in (67.7 cm)
Net weight: 2.1 lbs (0.96 kgs)
Net weight: 5.38 lbs (2.44 kgs)
Load capacity: 11 lbs (5 kgs)
Load capacity: 11 lbs (5 kgs)
One-year limited warranty
Visit www.rocketfishproducts.com for details.
© 2012 BBY Solutions, Inc., All Rights Reserved.
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richfield, MN USA 55423-3645
ROCKETFISH is a trademark of BBY Solutions, Inc. All other products and
brand names are trademarks of their respective owners.
ENGLISH 12-0791
Advertisement
