Table of Contents
Advertisement
Wiring Connections (continued)
Wiring diagram:
E
Advanced system configuration
N
G
L
Example Combination
I
≥ CD changer (CX-DP88U)
S
≥ Stereo power amplifier
H
≥ Upgraded system speakers
53
Ground Lead
Be sure to connect to a well
grounded metallic part of your
car because noises or troubles
may occur.
DIN Extension Cord
(Supplied to CA-CD55)
(If only 1 Changer is used, connect as indicated by
Changer Connector
CQ-DVR7000U
: Power Connector
Amplifier Unit
Connector
( CH
C-IN )
•
Changer Input Cord
( TWIN CD
C-CONT )
•
Dual Changer Control Cord
Brown/White Stripe
> 12 pin audio connector
Pre-out (Subwoofer)
Pre-out (Center)
Pre-out (Rear)
Pre-out (Front)
L
L
L
R
R
L : White
R : Red
Red (R)
White (L)
White (L)
Red (R)
RCA Cord
(Option)
Power
Stereo Power
Stereo Power
Amplifier
Amplifier
Amplifier
Upgraded System
Upgraded System
Center Speaker
Speakers
Speakers
72
CQ-DVR7000U
≥ This unit can be connected to an optional CD changer
(CX-DP88U). For details consult your nearest Panasonic dealer.
≥ For connection to the CD changer, refer to the operating
instructions of the CD changer (CX-DP88U).
CX-DP88U
Battery Lead
Yellow
DIN Connector
Fuse (3 A)
White (L)
Red (R)
Changer 1
Connecting
.)
Cord
( CD.C-2 )
CA-CD55
Dual Changer
White (L)
Red (R)
Output Cord
White (L)
White (L)
RCA Cord
Red (R)
Red (R)
(Option)
Fuse (3 A)
Battery Lead
( TWIN CD
C-CONT )
•
Ground Lead
2 Power Amplifier Unit
L
CX-DP88U
Control Unit Connector
RCA Cord
(Option)
Power
Amplifier
Set the gain of the external amplifier to
the medium, and adjust the volume
level using the unit's volume control.
Subwoofer
Parking Brake Cord
Caution
≥ For safety's sake, and to prevent accidents, the
parking brake cord must be connected.
≥ The parking brake connection should be
connected by a professional installer, if
possible. In case of difficulty, please consult
your nearest authorized Panasonic Servicenter.
Hand-operated parking brake
( CD.C-1 )
Foot-operated parking brake
Changer 2
Connecting
Cord
DIN
Connector
Yellow
Connecting the clamp connector ?
≥ Attach the clamp connector to the vehicle cord at a suitable
position.
≥ Note that if the cord being clamped onto is too thin
(0.3 mm
2
1 Push the end of the side brake cord into the hole on the
clamp connector.
Place the vehicle cord into the groove in the clamp
connector.
2 While making sure that the cords do not slip out of the
clamp connector, press the element down with a pair of
pliers.
3 Close the cover until it snaps shut.
Note:
≥ The position of the parking brake switch
depends on the car. (The figure shows
examples of where the switch might be
located.) For details on the exact location of
the parking brake switch in your car, contact
your dealer.
Brake Lamp
Chassis
Battery
? Clamp Connector
Of the 2 cords emerging from the parking
brake switch, connect the player's parking
brake cord to the one that is not connected to
the vehicle's chassis while the brake is in the
released state.
or less), the connection may not be adequate.
E
N
G
L
I
S
H
54
Parking Brake Switch
Cords connected to
the vehicle
Parking Brake Cord
PARKING BRAKE
Blue/Yellow Stripe
Vehicle Cord
Push the end of the cord
in until it touches this part.
Parking Brake Cord
Element
Cover
73
CQ-DVR7000U
Advertisement
Table of Contents
