Advertisement
Crossover Control: The variable crossover on the front of the amplifier allows you to adjust the crossover
frequency from 50-200Hz. The setting for this control is subjective; 80Hz is a good place to start.
Bass Boost Control: The variable bass boost control on the front of the amplifier is designed to give you
increased output 0-18dB, at 40Hz. The setting for this control is subjective. If you turn it up, you must readjust
the input gain control to avoid clipping the amplifier.
TROUBLESHOOTING
If your amplifier does not appear to be working, check the obvious things first such as blown fuses, poor or
incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is an illuminated
blue badge on top of the amplifier denoting the power state of the amp in addition to the Protection LEO on the
end panel of your KICKER IX series amplifier. When the blue badge is lit, this indicates the amplifier is turned on
and the amplifier is functioning properly.
BLUE Badge Light off, no output? With a Volt Ohm Meter (VOM) check the following:
0+
12 volt power
terminal (should read + 12V to+ 16V) @Remote turn-on terminal (should read + 12V to+ 16V) @)Check for
reversed power and ground connections. 0Ground terminal, for proper conductivity. 0Check for blown fuses.
BLUE Badge Light on, no output? Check the following: ORCA connections @Test speaker outputs with
a "known" good speaker. @)Substitute source unit with a "known" good source unit. 0Check for a signal in
the RCA cable feeding the amplifier with the VOM meter set to measure "AC" voltage. 0Check polarity of the
amplifier inputs if using a bridged configuration.
Protection LED flashing with loud music? The red LEO indicates low battery voltage. Check all the
connections in your vehicle's charging system. It may be necessary to replace or charge your vehicle's battery or
replace your vehicle's alternator.
Protection LED on, no output? 0Amplifier is very hot= thermal protection is engaged. Test for proper
impedance at the speaker terminals with a VOM meter (see the diagrams in this manual for minimum
recommended impedance and multiple speaker wiring suggestions). Also check for adequate airflow around
the amplifier. @Amplifier shuts down only while vehicle is running= voltage protection circuitry is engaged.
Voltage to the amplifier is not within the 10-16 volt operating range. Have the vehicle's charging and electrical
system inspected. @)Amplifier will only play at low volume levels= short circuit protection is engaged. Check
for speaker wires shorted to each other or to the vehicle chassis. Check for damaged speakers or speaker(s)
operating below the minimum recommended impedance.
No output from one channel? 0Check the balance control on source unit @Check the RCA (or speaker
input) and speaker output connections for the channel @)Swap the RCA (or speaker input) cable from left to
right. If the problem changes sides then you have a bad RCA (or speaker input) cable or source unit problem.
0Swap the speaker output wire from left to right. If the problem changes sides then you have a bad speaker
cable, passive crossover network and/or speaker.
Alternator noise-whining sound with engine's RPM? 0Check for damaged RCA (or speaker input) cable
@Check the routing of RCA (or speaker input) cable @)Check the source unit for proper grounding 0Check
the gain settings and turn them down if they are set too high.
Poor stereo image or reduced bass response? Check system phasing by turning the balance control from
left to right. If there is more bass output when turned to either side, then check your speaker wiring, passive
crossover networks and speaker terminals for proper positive and negative connections. Reverse a speaker
connection from positive to negative on the stereo/subwoofer channel(s); if the bass improves, the speaker was
out of phase.
No Fader? When using both sets of low-level (RCA) or high-level (speaker wire) inputs, the fader button must
be pushed in.
Ground Noise? KICKER amplifiers are engineered to be fully compatible with all manufacturers' head units.
Some head units may require additional grounding to prevent noise from entering the audio signal. If you are
experiencing this problem with your head unit, in most cases running a ground wire from the RCA outputs on the
head unit to the chassis will remedy this issue.
6
IX AMPLIFIERS
Advertisement
