Related Manuals for TTS Tuff-Cam 2
Summary of Contents for TTS Tuff-Cam 2
- Page 1 Please Read All Instructions Carefully Before Using User Guide Version 1...
- Page 2 • In the event of an electro-static discharge, your • Tuff-Cam 2 may malfunction. In this case, please use a pen to operate the reset switch on the side to restore normal operation Warranty is void if the case is opened for any reason •...
- Page 3 Tuff-Cam 2 User Guide residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
- Page 4 Tuff-Cam 2 User Guide Know Your Tuff-Cam 2 2 2 2...
-
Page 5: Taking A Photo
Tuff-Cam 2 User Guide Taking a Photo Slide the Mode switch to PHOTO • Turn ON the camera, by pressing the On/Off • switch briefly Point the camera at the subject • Press the trigger button to take the photo •... -
Page 6: Switching On And Off
Tuff-Cam 2 User Guide NB. You can also press and hold the trigger button • and Tuff-Cam 2 will take a video for the whole time that the button is pressed (memory permitting) Displaying the Photos & Videos Slide the Mode switch to PLAY •... -
Page 7: Using The Menu System
Tuff-Cam 2 User Guide Using the Menu System There are different Menu options available for the • different positions of the Mode switch; Play, Video and Photo Press the Menu button briefly to enter the • appropriate Menu options for the selected Mode Press the Menu button once more to move the to •... -
Page 8: Setup Menu Options
Tuff-Cam 2 User Guide EV/Exposure correction: -2.0 to +2.0 • White balance: Auto, Daylight, Cloudy, Tungsten, • Fluorescent ISO: Auto, 100, 200 • Colour: Standard, Vivid, Sepia, Monochrome • Saturation: Normal, High, Low • Sharpness: Normal, Hard, Soft • Preview: On, Off •... -
Page 9: Video Menu Options
• Slide show: 3 sec, 5 sec, 10 sec • Protect: Single, All, Selection • Thumbnail: • Volume: 1 to 8 Connecting to a PC or Apple Mac • There are two modes in which the Tuff-Cam 2 can connect to a PC: MSDC or PC-CAM... -
Page 10: Charging The Battery
• To select PC-Cam mode, move the slide switch to PHOTO or VIDEO before connecting to the PC Charging the Battery • Tuff-Cam 2 is supplied with a partially charged battery and can be used immediately without charging first • The battery can be charged by connecting to any active USB port. -
Page 11: Installing Software
Tuff-Cam 2 If you wish to use Tuff-Cam 2 as a PC-Cam (Web Cam) or to use the ULead Photo Explorer software, then you will need to install the software from the CD. - Page 12 Tuff-Cam 2 User Guide To operate the Tuff-Cam 2 as a PC-Cam (Web Cam), select “Install PC-Cam Driver”. To install the ULead Photo Explorer 8.6 photo and video editing software, select “Install ULead Photo Explorer” When all required software has been installed, press “Exit”...
-
Page 13: Specifications
Tuff-Cam 2 User Guide Specifications • Sensor: 5 Mpixel CMOS • Display: 2 inch, 640 x 240 TFT • Internal storage: 32 Mb • Additional storage: SD Card slot supports up to 2GB • Built-in Li-Ion battery: 3.7V, 2200mAh • Battery life: 9 hours continuous video or over 2 years in standby •... -
Page 14: Troubleshooting
Tuff-Cam 2 User Guide Troubleshooting • Tuff-Cam 2 is designed to work reliably and predictably in all normal conditions. However, it is possible that problems may occur. Please check the following before contacting technical support: Problem ESD causes unit to malfunction... -
Page 15: Support And Warranty
This product is provided with a one-year warranty for problems found during normal usage. Mistreating the Tuff-Cam 2 or opening the unit will invalidate this warranty. Any data stored on the unit and any consequential loss is not covered by this warranty. The battery is not user replaceable.