Kenmore 795.7202 Series Use & Care Manual page 29

The concentration of the indicated substances in water entering the system was reduced to a concentration less than or
equal to the permissible limit for water leaving the system as specified in NSF/ANSI Standard 42.
System tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction of
substances listed below.
Capacity 500 Gallons (1,892 Liters)
Contaminant Reduction
Chlorine Taste and Odor
Nominal Particulate Class III,
48,000 pts/mL
≥ 5.0 to < 15.0 μm
Application Guidelines/Water Supply Parameters
Service Flow
Water Supply
Water Pressure
Water Temperature
It is essential that the manufacturer's recommended
installation, maintenance and filter replacement
requirements be carried out for the product to perform as
advertised.
NOTE: While the testing was performed under standard
laboratory conditions, actual performance may vary.
Replacement Cartridge: GEN11042FR-08.
To purchase a replacement filter, visit your local Sears
store or call 1-800-4-MY-HOME. Visit us on the web at
www.sears.com/partsdirect.
SAFETY INFORMATION
Read, understand, and follow all safety information
contained in these instructions prior to use of the
KENMORE® Model GEN11042F-08 drinking water
system. Retain these instructions for future reference.
Intended Use:
The KENMORE® Model GEN11042F-08 drinking water
system is intended for use in filtering contaminants from
drinking water as listed on the Performance Data Sheet,
and has not been evaluated for other uses. The system
is installed inside the refrigerator and must be installed,
operated and maintained as specified in the installation
and use instructions.
Model: GEN11042F-08
Average Influent Challenge
Influent Concentration
2.0 mg/L 2.0 mg/L ± 10%
At least 10,000 particles/mL
0.5 gpm (1.89 lpm)
Potable Water
20 -125 psi (138 – 862 kPa)
34 ºF - 100 ºF (1.1 ºC - 37.8 ºC)
Performance Data Sheet
Use Replacement Cartridge GEN11042FR-08
Contaminant Reduction Determined by NSF testing.
Average Product
Water Concentration
mg/L
7.5 mg/L
To reduce the risk associated with ingestion of
contaminants:
Do not use with water that is microbiologically unsafe
or of unknown quality without adequate disinfection
before and after the system.
To reduce risk of property damage due to water leakage:
• Read and follow Use Instructions before installation and
use of this system.
• Installation and use MUST comply with all state and local
plumbing codes.
• Protect filter from freezing. Remove filter in temperatures
below 34°F (1.1°C).
• Do not install on hot water supply lines. The maximum
operating water temperature of this filter system is 100°F
(37.8°C).
• Do not install if water pressure exceeds 125 psi (862
kPa). If your water pressure exceeds 80 psi (552 kPa), you
must install a pressure limiting valve. Contact a plumbing
professional if you are uncertain how to check your water
pressure.
• Do not install where water hammer conditions may
occur. If water hammer conditions exist you must install a
water hammer arrester. Contact a plumbing professional
if you are uncertain how to check for this condition.
• Where a backflow prevention device is installed on a
water system, a device for controlling pressure due to
thermal expansion must be installed.
• The disposable filter cartridge MUST be replaced
every six months, at the rated capacity or sooner if a
noticeable reduction in flow rate occurs.
29
Average % Max Effluent
Reduction Mg/L
97.4% 0.06 mg/L
99.9% 26 mg/L
WARNING
CAUTION
WATER FILTER
Min. Required
Reduction
≥ 50%
≥85%