Advertisement
English
IMPORTANT!
- The voltage selector located at the bot-
tom of this system is preset at 220V-240V
from the factory. For countries that oper-
ate at 110V-127V, please adjust to 110V-
127V before you switch on the system.
Supplied Accessories
– AC power cord
Top/front panels
(See 1)
1
OPEN/CLOSE
– opens/closes the CD
door.
2 § ∞
SKIP
– selects the next/previous track
– searches forwards/backwards (press and
hold the button) within the current track
3 9 STOP – stops CD playback;
– erases a CD program
2/; PLAY/PAUSE
4
– starts or pause CD
playback
5 REPEAT – repeats a track/
CD program/entire CD.
6
PROG.
– programs tracks and reviews the
program
7 DBB – turns the bass enhancement on/off.
8 Telescopic antenna - improves FM
reception.
9
LED Display
– shows the CD functions
Controls/Power Supply
Back/bottom panel (
See 1)
0
VOL
– adjusts volume level.
! Source selector: CD,TUNER, OFF
– selects CD or radio source of sound
– power off switch
@ Battery door – open to insert
8
x 1.5V
R-14/ UM-2/ C-cells
# Voltage selector – adjust to match the
local voltage 110/220V before plugging in the
set
1 2
$ TUNING
– tunes to radio stations
% BAND – selects
MW, FM or FM
ST. waveband
^ AC MAINS~ - inlet for power cord.
& p – 3.5 mm stereo headphone socket
Helpful hints: The speakers will be muted
when headphones are connected to the set.
CAUTION
Use of controls or adjustments or
performance of procedures other
than herein may result in unsafe
operation.
Power Supply
Whenever convenient, use the power supply
cord if you want to conserve battery life.
Make sure you remove the plug from the set
and wall outlet before inserting batteries.
Batteries (not included)
1 Open the battery door and insert
8
batteries,
type R-14, UM-2 or C-cells, (preferably
alkaline) with the correct polarity as indicated
by the "+" and "–" symbols inside the com-
partment. (See 1)
2 Replace the battery door, making sure the bat-
teries are firmly and correctly in place.The set is
now ready to operate.
Batteries contain chemical substances, so
they should be disposed of properly.
Power Supply
•
Incorrect use of batteries can cause electrolyte
leakage and will corrode the compartment or
cause the batteries to burst:
•
Do not mix battery types: e.g. alkaline with car-
bon zinc. Only use batteries of the same type
for the set.
•
When inserting new batteries, do not try to mix
old batteries with the new ones.
•
Remove the batteries if the set is not to be used
for a long time.
Using AC power
WARNING: Always check you have com-
pletely switched off the set, before you
change or disconnect power supply.
1 Check if the power voltage, as shown on
the type plate located on the
bottom of the set, corresponds to your
local power supply. If it does not, consult your
dealer or service center.
2 If your set is equipped with a voltage selec-
tor, adjust the selector so that it matches
with the local power supply.
3 Connect the power cord to the AC
MAINS~ inlet and the wall socket.The set is
now connected and ready for use.
4 To switch the set off completely, withdraw the
power cord from the wall socket.
5 Install the unit near the AC outlet and where
the AC power plug can be easily reached.
•
Disconnect the power cord from the wall
socket to protect your set during heavy
thunderstorms.
The type plate is located on the
bottom of the set.
Helpful hints:
–
To avoid unnecessary energy consumption,
always adjust the Source selector to OFF
after using the set.
General Operation/Tuner
General operation
Switching on and off and selecting the
function
1 To select your sound source, adjust the
Source selector to: CD or TUNER.
2 To switch off the set, adjust the Source
selector to OFF position.
Adjusting volume and sound
Adjust the sound with the
VOL
and DBB
controls.
Radio reception
1 Adjust the Source selector to TUNER.
2 Adjust BAND to select your desired
waveband,
MW, FM or FM
ST. .
FM ST. LED will light up when radio is
receiving stereo broadcast.
1 2
3 Turn TUNING
to tune to a station.
Helpful hints:
To improve radio reception
•
For FM, extend, incline and turn the telescop-
ic antenna for best reception. Reduce its
length if the signal is too strong.
To tune to a weak FM station, adjust BAND
to FM (mono).
•
For
MW,
the set uses a built-in antenna.
Direct this antenna for best reception by
turning the whole set.
Advertisement
