Subscribe to Our Youtube Channel
Related Manuals for Audio Research Definition DSi200
Summary of Contents for Audio Research Definition DSi200
- Page 1 Owner’ s Manual D E F I N I T I O N S E R I E S Model DSi200 STEREO INTEGRATED AMPLIFIER 3900 ANNAPOLIS LANE NORTH / PLYMOUTH, MINNESOTA 55447-5447 / PHONE: 763-577-9700 FAX: 763-577-0323 www.audioresearch.com...
-
Page 2: Table Of Contents
Contents Model DSi200 Section Page No. Preface..............1 Warnings . - Page 3 Model DSi200 D E F I N I T I O N S E R I E S D I S P L A Y VOLUME INPUT POWER MONO INVERT MUTE INT EGRA TED AMPLI FIER D S I 2 0 0 HIGH D EFINITION ®...
-
Page 4: Preface
The rotary control on the right selects any of 5 input 2. This unit operates on voltages which can cause serious sources connected to the DSi200: Bal 1, Bal 2, CD, Tuner injury or death. Do not operate with covers removed. -
Page 5: Connections
DSi200 connects to the appropriate-channel (-) gold binding post is unmuted. on the DSi200. Connect the red or (+) speaker terminal to the wire that connects to the appropriate-channel (+) bind- INVERT: Inverts absolute phase of output signal. Remem- ing post on the DSi200. -
Page 6: Installation
3. Make sure the DSi200 is properly connected to a ground- ed high-current power receptacle via the supplied With proper installation, the DSi200 may be left on contin- 14-gauge, 3-prong grounded power cord (see AC POWER uously for maximum performance on demand;... -
Page 7: Servicing
In the unlikely event that technical service beyond the abil- A small, soft paint brush is effective in removing dust from ity of the importer is required, Audio Research will fulfill bevels, the recessed nameplate and other features of the the terms and conditions of the Limited Warranty. -
Page 8: Specifications
1 " (3.8 cm) forward of the " thick front panel. Output connectors extend 0.9" behind rear panel. WEIGHT: 37.2 lbs. (16.9 kg) Net; 43.3 lbs. (19.7 kg) Shipping. Specifications subject to change without notice. ©2009 Audio Research Corporation. - Page 9 Model DSI200...
- Page 10 Model...
- Page 11 (3.8 cm) forward of the front panel. WEIGHT: 16.5 lbs. (7.5 kg) Net; 26 lbs. (11.8 kg) Shipping. Specifications subject to change without notice. ©2006 Audio Research Corporation. 800 watts maximum SENSITIVITY: 0.9V RMS for rated output (32.7dB Gain) sin- gle-ended or balanced.
-
Page 12: Installation Of Vacuum Tubes
(CD, Tuner, Phono, etc.), press monitor switch again. Note: The gain of the DSI200 through the monitor input is not adjustable by gain selector button (on the remote), and is fixed at “High” gain (the gain setting on the display is unlit in the “Monitor”... -
Page 13: Tape Recording Procedure
When recording from the Processor input to the button (front panel and on remote) should be selected Record out of the DSI200, the level of the recording will be to match the type of connection used (BAL or SE) on each dependent on the level setting of the processor. - Page 14 Press “Mute” to initiate operation. 4. Select input source, then BAL or SE as necessary. The DSi200 should be turned on a f t e r the source compo- nents of your system. If the DSi200 is turned on before...
Need help?
Do you have a question about the Definition DSi200 and is the answer not in the manual?
Questions and answers