Husqvarna CTH171 Instruction Manual

Husqvarna CTH171 Instruction Manual

Husqvarna lawn mower instruction manual
Table of Contents

Advertisement

CTH151, CTH171
CTH172, CTH191
Instruction manual
Please read these in struc tions care-
ful ly and make sure you un der stand
them before using this ma chine.
Anleitungshandbuch
Bitte lesen Sie diese Anleitungen sorg-
fältig durch und vergewissern Sie sich,
daß Sie diese verstehen, bevor Sie die
Maschine in Betrieb nehmen.
Manuel d'instructions
Merci de lire trés attentivement le
manuel d'instructions. Assurez-vous
d'avoir tout compris avant d'utiliser ce
tracteur.
Manual de las instrucciones
Por favor lea cuidadosamente y com-
prenda estas intrucciones an tes
de usar esta maquina.
02228_Husqvarna_CRD
Manuale di istruzioni
Prima di utilizzare la macchina leggete
queste istruzioni con attenzione ed ac-
certatevi di averle comprese bene.
Instructieboekje
Lees deze instructies aandachtig en
zorg dat u ze begrijpt voordat u deze
ma chine gebruikt.

Advertisement

Table of Contents
loading

Summary of Contents for Husqvarna CTH171

  • Page 1 CTH151, CTH171 CTH172, CTH191 Instruction manual Please read these in struc tions care- ful ly and make sure you un der stand them before using this ma chine. Anleitungshandbuch Bitte lesen Sie diese Anleitungen sorg- fältig durch und vergewissern Sie sich, daß...
  • Page 2 Safety rules. Sicherheitsvorschriften. Règles de sécurité. Assembly. Zusammenbau. Montage. Functional description. Funktionsbeschreibung. Description du fonctionnement. Before starting. Maßnahmen vor dem Anlassen. Avant de démarrer. Driving. Betrieb. Conduite. Maintenance, adjustment. Wartung (Instandhaltung), Einstellung. Manutenzione. Entretien, réglages. Troubleshooting. Störungssuche. Recherche des pannes. Storage.
  • Page 3: Safety Rules

    Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. Training • Read the instructions carefully. Be familiar with the con trols and the proper use of the equipment.
  • Page 4 • Reduce the throttle setting during engine run-out and, if the engine is provided with a shut-off valve, turn the fuel off at the conclusion of mowing. IV. Maintenance and Storage • Keep all nuts, bolts and screws tight to be sure the equip- ment is in safe working condition.
  • Page 5 Regeln für die sichere Bedienung von Rasentraktoren WICHTIG: DIESE MÄHMASCHINE KANN HÄNDE UND FÜSSE ABTRENNEN UND GEGENSTÄNDE MIT HOHER GESCHWINDIGKEIT SCHLEUDERN. NICHTBEACHTUNG DER FOLGENDEN SICHERHEITSVORSCHRIFTEN KÖNNTE SCHWERE ODER TÖDLICHE VERLETZUNGEN ZUR FOLGE HABEN. I. SCHULUNG • Die Anleitungen sorgfältig durchlesen. Mit den Bedien- ungselementen und der vorschriftsmäßigen Bedienung der Maschine vertraut machen.
  • Page 6 • Alle Anbaugeräte-Antriebe ausschalten, den Motor abstel- len und das (die) Zündkerzenkabel abziehen bzw. den Zündschlüssel abziehen: - vor dem Entfernen von Verstopfungen aus dem Mäh- werk oder dem Auswurf; - vor dem Prüfen, Reinigen oder Reparieren des Rasenmähers; - nachdem auf ein Fremdkörper gestoßen wurde. Den Rasenmäher auf Schäden untersuchen und die Reparaturen durchführen, bevor die Maschine wieder angelassen und in Betrieb genommen wird;...
  • Page 7 Conseils pour l’utilisation en toute sécurité des tracteurs de pelouse ATTENTION: CE TRACTEUR DE PELOUSE EST CAPABLE D’AMPUTER MAINS OU PIEDS ET DE PROJETER DES OBJETS.L’INOBSERVATION DES RÈGLES DE SÉCURITÉ CI-DESSOUS PEUT ÊTRE LA CAUSE DE BLESSURES SÉRIEUSES VOIRE MORTELLES. I.
  • Page 8 • Avant de quitter le siége : - débrayer les lames et abaisser le carter de coupe, - mettre le levier de vitesse au point mort et enclencher le frein de parking, - arrêter le moteur et retirer les clés, •...
  • Page 9 Prácticas de Operación Seguras para las Segadoras Conducibles IMPORTANTE: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE. I.
  • Page 10 • Desenganche la transmisión a los accesorios, pare el mo- tor, y desconecte el (los) cable (s) de la bujía o remueva la llave de ignición - antes de limpiar bloqueos o desatrancar del con- ducto; - antes de inspeccionar, limpiar o trabajar sobre la segadora;...
  • Page 11 Regole di sicurezza per trattorini da prato ATTENZIONE: QUESTO TRATTORINO TOSAERBA HA UNA POTENZA SUFFICIENTE AD AMPUTARE MANI E PIEDI E A SCAGLIARE OGGETTI. LA MANCATA OSSERVANZA DELLE SEGUENTI ISTRUZIONI ANTINFORTUNISTICHE POTREBBE CAUSARE LESIONI GRAVI E PERSINO IL DECESSO DELLA VITTIMA. I.
  • Page 12 • Disinnestare la trasmissione del moto agli accessori, spegnere il motore e scollegare i fi li delle candele op- pure togliere la chiavetta di accensione: - prima di pulire eventuali intasamenti e pri ma di stasare lo scivolo; - prima di interventi o controlli sul tosaerba e prima delle operazioni di pulizia;...
  • Page 13 Veilige bedieningsmethoden voor zittrekkers BELANGRIJK: DEZE MAAIMACHINE KAN HANDEN EN VOETEN AMPUTEREN EN VOORWERPEN WEGSLINGEREN. HET NIET OPVOLGEN VAN DEZE VEILIGHEIDSINSTRUCTIES KAN ERNSTIG OF DODELIJK LETSEL TOT GEVOLG HEBBEN. I. TRAINING • Lees de instructies aandachtig. Zorg dat u vertrouwd bent met de bedieningselementen en het juiste gebruik van de machine.
  • Page 14 ORANGEBURG, SC 29116 2005 EN836:1997/A2 ISO 3744 ISO 11094 Vibration Vibration SERIAL NO. Vibración Vibrering Vibrasjon 02682 CTH151 CTH171 CTH172 CTH191 15/11,2 17/12,7 17/12,7 19/14,3 0-7,3 0-7,3 38-102 38-102 98/37/EC LpA < 90 dBa 2000/14/EC LwA < 100 dBa EN 1033 Lärmpegel...
  • Page 15 These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole fi nden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut.
  • Page 16 These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole fi nden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut.
  • Page 17 01738 GEFAHR AUGEN SCHÜTZEN EXPLOSIVE GASE KÖNNEN ERBLINDUNG UND KÖRPERVERLET- ZUNGEN VERURSAC- HEN. GEVAAR OGEN BESCHERMEN EXPLOSIEVE GASSEN KUNNEN BLINDHEID OF LETSEL VERO- ORZAKEN. PELIGRO PROTEJE SUS OJOS GASES EXPLOSIVOS PUEDEN CAUSAR CE- GUE-DAD O LESIONES. PERICOLO RIPARARE GLI OCCHI VAPORI ESPLOSIVI PUO’...
  • Page 18 2. Assembly. 2. Zusammenbau. 2. Montage. 2. Montaje 2. Montaggio. 2. Montering. Before the tractor can be used certain parts must be as- sem bled, which for transportation reasons are enclosed in the packing. Vor der Anwendung des Aufsitzmähers müssen gewisse Teile eingebaut werden, die aus Transportgründen in der Verpack-ung lose beigefügt sind.
  • Page 19 VOLANT DE DIRECTION • Monter la rallonge d'arbre de direction (1). • Positionner le cache sur la colonne de direction. S'assurer que les ergots du cache colonne de direction sont bien clipsés dans les quatre orifi ces du tableau de bord. •...
  • Page 20 Seat Remove the hardware securing seat to the cardboard pack ing and set the hardware aside for assembly of seat to tractor. Pivot seat upward and remove from cardboard packing. Re- move the cardboard packing and discard. Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan (1).
  • Page 21 1. Battery Cover 1. Tapador del acumulador 2. Cable Positive (+) 2. Cable positivo (+) 3. Cable Negative (-) 3. Cable negativo (-) 4. Fender 4. Protección 5. Battery terminal 5. Terminal de batería 6. Battery 6. Batería 1. Batterieabdeckung 1.
  • Page 22 WARNING: Positive terminal must be con nect ed fi rst to prevent sparks from ac ci den tal grounding. Remove terminal caps and discard. Connect the red cable to + and then the black earth ca ble to -. Screw tight the cables.
  • Page 23 To install bagger com po nents to tractor 1. Dis charge Chute 2. 3/8 Nut 3. Flat Washer • Remove discharge chute from rear of tractor. Unhook the two (2) straps and pull chute out and away from tractor. • Remove the two (2) 3/8 nuts and fl...
  • Page 24 1. Front bagger tube 2. Lower bagger tube 3. 1/4 x 50,8mm Car riage Bolts 4. 1/4 Lock nut 1. Front bagger tube 2. 1/4 x 50,8mm Car riage Bolts 3. 1/4 Lock nut 4. Vinyl Binding 5. Dump handle tube 6MM (1/4") - 9MM (3/8") 6.
  • Page 25 Installation der Aufhängung der Grasfangbox des Traktors 1. Auswurfkanal 2. Kontermutter 3/8 3. Flache unterlegscheibe • Nehmen Sie den Auswurfkanal aus dem hinteren Teil des Traktors. Lösen Sie beide (2) Klammern und ziehen Sie den Kanal aus dem Traktor. • Entfernen Sie die zwei (2) 3/8-Zoll-Muttern und fl...
  • Page 26 1. Vorderer Rahmen der Grasfangbox 2. Unterer Rahmen der Grasfangbox 3. Tragbolzen 1/4 x 50,8mm 4. Kontermutter 1/4 1. Vorderer Rahmen der Grasfangbox 2. Bolzen 3. Kontermutter 1/4 4. Vinylverkleidung 5. Rohr des Handgriffs zum Entleeren der Grasfang- 6. Fixierfeder 7.
  • Page 27 Assemblage des composants du collecteur 1. Goulotte d'éjection 2. Ecrou 3/8 3. Rondelle plate • Retirer la goulotte d'éjection (1). Pour cela, libérer les deux attaches élastiques à l'arrière du tracteur et tirer la goulotte d'éjection hors du tracteur. • Dévisser et retirer les deux écrous ainsi que les deux rondelles plates des vis situées sur le panneau arrière du tracteur (Voir fi...
  • Page 28 1. Armature frontale 2. Armature inférieure 3. Boulon poêlier 1/4 x 50,8 mm 4. Ecrous freins 1/4" 1. Armature frontale 2. Boulon poêlier 1/4 x 50,8 mm 3. Ecrous freins 1/4 4. Bande d’étanchéité en vinyle 5. Levier de vidage du collecteur 6.
  • Page 29 Para montar los componentes del contenedor para costales al tractor 1. Descarga de adaptarse 2. Tuercas de 3/8 3. Arandelas planas • Quite el colector de la parte trasera del tractor. Desbloquee las dos (2) grapas y tire el colector fuera del tractor. •...
  • Page 30 1. Tubos frontales del contenedor 2. Tubos inferiores del contenedor 3. Tornillos portadores 1/4 x 50,8mm 4. Contratuercas 1/4 1. Tubos frontales del contenedor 2. Tornillos14x50,8 mm 3. Contratuercas 1/4 4. Capas de vinil 5. Tubo de la manilla 6. Resorte fi jador 7.
  • Page 31 Per montare i componenti del cesto di raccolta 1. Convogliatore di scarico 2. Dadi 3/8 3. Rondella Piatta • Rimuovere il convogliatore dalla parte posteriore del trattore. Allentare le due graffe, sganciare ed estrarre il convogliatore. • Rimuovere i due (2) dadi da 3/8 e le rondelle piatte dai bulloni sulla piastra posteriore del trattore.
  • Page 32 1. Piastrina d'arresto dell'asta di scarico 2. Telaio inferiore del cesto 3. Bulloni di supporto 1/4 x 50,8 mm 4. Dadi 1/4 1. Telaio anteriore 2. Bulloni 1/4 x 50,8 3. Dadi 1/4 4. Rivestimento in plastica 5. Asta di scarico 6.
  • Page 33 Hetmonteren van componenten van de grascontainer op de trekker 1. Afvoertrechter 2. 3/8 borgmoer 3. Vlakke sluitring • Verwijder de afvoertrechter van de achterzijde van de trek ker. Haak de twee (2) riemen los en trek de trechter van de trekker af. •...
  • Page 34 1. Voorstenn 2. Onderste container steun 3. 1/4 x 50,8 mm slotbouten 4. 1/4 Borgmoer 1. Voorstenn 2. 1/4 x 50.8 mm bouten 3. 1/4 Borgmoeren 4. Vinylafdichting 5. Hendel voor legen 6. Vorkbout 7. Sluitveer 8. Hetten 1. Bovenoppervlakten gelyk 2.
  • Page 35 TO ADJUST GAUGE WHEELS Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain con di tions. •...
  • Page 36 3. Functional description. 3. Funktionsbeschreibung. 3. Description du fonctionnement. 3. Descripción del funcionamiento. 3. Funzionamento. 3. Beschrijving van functies Positioning of controls 1. Light Switch Position. 2. Throttle/Choke control. 3. Brake and clutch pedal. 4. Motion Control Lever. 5. Connection/disconnections of the cutting unit. 6.
  • Page 37 Emplacement des commandes 1. Interrupteur de commande des phares 2. Commande des gaz et starter 3. Pédale d'embrayage et de frein 4. Levier de commande de la transmission hydrostatique 5. Embrayage/débrayage du carter de coupe 6. Relevage et abaissement du carter de coupe 7.
  • Page 38 1. Light switch position 1. Lichtschalter 1. Interrupteur des phares 1. Interruptor de alumbrado 1. Interruttore luci 1. Schakelaar verlichting 2. Throttle and choke control The accelerator control regulates the motor speed and also the speed of the blades. If the lever is in its forward position the choke function is con nect ed.
  • Page 39 3. Brake and clutch pedal When the pedal is pushed down the brake is applied and the motor is disengaged. 3. Brems- und Kupplungspedal Beim Vorwärtsdrücken des Pedals wird das Fahrzeug abge- bremst. Gleichzeitig wird der Motor ausgekuppelt und das Fahrzeug rollt aus.
  • Page 40 4. Motion control lever There are four different positions for this lever: N = Neutral (no drive) S = Slow F = Fast R = Reverse The lever can be moved steplessly between S and F to ensure the required speed. 4.
  • Page 41 01842 5. Connection/disconnection of the cutting unit Move the lever forward to connect the drive to the cutting unit, whereby the drive belt is tensioned and the blades begin to rotate. If the lever is moved backwards the drive will be disconnected and the rotation of the blades slowed down by the action of the brake shoes on the pulley.
  • Page 42 7. Ignition Lock There are three different positions for the ignition key: All electric current bro ken. Electric current connected. START Start motor connected. WARNING! Never leave the key in the ignition lock when leaving the machine on its own. 7.
  • Page 43 8. Frein de stationnement Pour enclencher le frein de stationnement : 1. Enfoncer à fond la pédale d'embrayage/frein. 2. Relever vers le haut le levier du frein de stationnement et le maintenir dans cette po si tion. 3. Relâcher la pédale d'embrayage/frein. Relâcher le levier du frein de stationnement qui restera dans sa position verrouillée (en haut).
  • Page 44 10. Cutting height setting The required cutting height is set with the aid of the wheel. The cutting height is increased when it is turned clockwise. The wheel is easier to turn if the lever for lifting/lowering of the cutting unit is pulled backwards at the same time. 10.
  • Page 45 4. Before starting. 4. Maßnah men vor dem Anlassen. 4. Avant de démarrer. 4. Antes del arranque. 4. Prima dell’avviamento. Filling up The en gine should be run of pure (not oil mixed) un lead ed petrol. Do not fi ll beyond the lower edge of the fi lling hole. Do not fi...
  • Page 46 Oil level The combined oil refi lling cap and the oil stick is ac ces si ble when the bonnet is lifted for wards. The oil level in the engine should be checked before each run. Make sure that the tractor is ho ri zon tal.
  • Page 47 Tire air pressure Check the tire pressure regularly. The pres sure in the front tire should be 1 bar (14 PSI) and 0.8 bar (12 PSI) in the back tires. Reifendruck Den Luftdruck in den Reifen regelmäßig prüfen. Der Druck in den Vorderreifen soll 1 bar betragen, in den Hinterreifen 0,8 bar.
  • Page 48 5. Driving. 5. Betrieb. 5. Conduite. 5. Conducción. 01842 Starting of motor Make sure that the cutting unit is in the transport position (top position) and that the lever for connection/disconnection of the cutting unit is in the disconnection position. Anlassen des Motors Darauf achten, daß...
  • Page 49 Cold motor: Push the gas control up to end positon choke ( ). Bei kaltem Motor: Gashebel in die Endstellung choke ( ) schieben. Avec un moteur froid: pousser l'accélérateur vers le haut à la limite du starter choke ( ). Con el motor frío: Empuje el acelerador hacia arriba hasta la posición choke ( ) [estrangulación].
  • Page 50 01949 Turn the ignition key to “START position”. NOTE! Do not run the start motor more than 5 sec onds at once. If the engine will not start, wait about 10 sec onds before the next try. Zündschlüssel auf “START” drehen. HINWEIS! Den Anlasser nicht jeweils länger als ca.
  • Page 51 IMPORTANT! COLD STARTING FOR HYDRO COLD STARTING FOR HYDRO (BE LOW 40°F[4°C]) - AF TER STARTING ENGINE AND BEFORE DRIVING, LET TRANS- MIS SION WARM UP FOR ONE (1) MINUTE BY PLACING MOTION CONTROL LEVER IN NEU TRAL (N) PO SI TION AND RELEASING CLUTCH/BRAKE PEDAL.
  • Page 52 • Débrayer la transmission en plaçant la commande de roue libre sur sa position de marche en roue libre (Se référer à la section "TRANSPORT" de ce livret). • Démarrer le moteur et mettre la commande des gaz en position de ralenti. S'assurer que le frein de stationnement n'est pas serré.
  • Page 53 NOTE! The machine is equipped with a safety switch which immediately breaks the current to the en gine if the driver leaves the seat with en gine run ning and with the con nec tion/dis con nec tion le ver in position “connection”.Your machine is also equipped with a system that will not allow mower to operate if the bagger or op tion al rear discharge defl...
  • Page 54 Cutting tips • Clear the lawn from stones and other objects which can be thrown away by the blades. • Localize and mark stones and other fi xed objects to avoid collision. • Begin with a high cutting height and reduce until the required cutting result is obtained.
  • Page 55 Consejos para el corte • Limpie el césped de piedras y otros objetos que puedan ser proyectados por las cuchillas. • Localice y marque piedras y otros objetos a fi n de evitar el choque con ellos. • Empiece con una altura de corte alta y vaya disminuyé- ndola hasta alcanzar el resultado deseado.
  • Page 56 02207 To Dump Bagger Your tractor is equipped with a Dump Bag Alarm. To turn off the alarm disengage the attachment clutch switch. • Position tractor in location you wish to dump bagger. • Place motion control lever in Neutral position and set parking brake.
  • Page 57 To convert mower (Converting to mulching or rear discharging will re quire the purchase of these ac ces so ries.) To mulching • Place deck into the high cut position. • Remove bagger or optional rear discharge defl ector. • Unhook the two (2) straps and remove discharge chute.
  • Page 58 Para cambiar el ajuste de la segadora (Un cambio de ajuste para no recoger la hierba o usarla tipo mulching requiere la compra de los mecanismosdispositivos siguientes) Para cortar tipo mulching • Meta la plataforma en posicion de siega alta •...
  • Page 59 WARNING! • Do not drive in terrain at an angle of more than max. 5°. The risk for spark-over back wards is large. • In steep terrain the risk for tipping is considerable. • Avoid stopping and starting in sloping terrain. WARNUNG! •...
  • Page 60 WARNING! Do not leave the ignition key in the machine when not in use to prevent children and other unauthorized persons starting the en gine. WARNUNG! Den Zündschlüssel niemals im Zündschloß sitzen lassen, wenn die Machine unbeaufsichtigt verlassen wird, damit nicht Kinder und unbefugte Personen den Motor anlassen können.
  • Page 61 6. Maintenance, adjustment. 6. Wartung (Instandhaltung), Einstel- lung. 6. Entretien, réglages. 6. Mantenimiento, ajuste. 6. Manutenzione. 6. Onderhoud, afstelling. WARNING! Before servicing the engine or cutting unit the fol low ing shall be carried out: • Press down the clutch/brake pedal and engage the parking brake lever.
  • Page 62 01837 (1) Hood (2) Headlight wire connector (1) Motorhaube (2) Scheinwerferanschluß (1) Capot (2) Connexion des phares (1) Cubierta (2) Conector de cables de los faros delanteros (1) Cofano (2) Connettore cavo luci (1) Motorkap (2) Aansluitkabel koplampen • • •...
  • Page 63 Maintenance NOTE: Periodic maintenance should be performed on a regular basis in order to keep your tractor in good running condition. WARNING: Disconnect spark plug wire to prevent ac ci - den tal starting before attempting any repair, inspection, or main te nance.
  • Page 64 To service engine See engine manual. Oil drain valve • Remove cap and install drain tube. • To open valve, push in slightly, turn counterclockwise and pull out. • To close valve, push in and turn clockwise . • Remove drain tube and install cap. 1.
  • Page 65 SERVICE RECORD Fill in dates as you complete regular service Change engine oil (without oil fi lter) ... Change engine oil (with oil fi lter) ... Lubricate pivot points ... Check brake operation ... Clean air screen ... Clean air fi lter and pre-cleaner... Replace air cleaner paper cartridge...
  • Page 66 SCHEMA D'ENTRETIEN Consigner les dates d'intervention après chaque opération d'entretien. Vidange de l'huile moteur (sans fi ltre à huile Vidange de l'huile moteur (avec fi ltre à huile) ... Graissage des articulations... Vérifi cation des freins ... Nettoyage de la grille d'aération ... Nettoyage du fi...
  • Page 67 DATI DI SERVIZIO Compilare ogni qualvolta si esegue un regolare servizio Cambio dell'olio (Senza fi ltro dell’olio)... Cambio dell'olio (Con fi ltro dell’olio) ... Lubrifi cazione punti di articolazione ... Controllo freni... Pulizia schermo aria... Pulizia fi ltro aria e prefi ltro... Sostituzione depuratore aria ...
  • Page 68 Blades The blades should be sharp to achieve best cutting results. Sharpening can be carried out with a fi le or grinding disc. NOTE: It is very important that both blades are sharpened equally to avoid imbalance. Messerbalken Für ein gutes Mähergebnis müssen die messcrbalken scharf sein.
  • Page 69 1. Hex bolt right hand 5. 5 Star Center Hole thread ed. 6. 5 Star Pattern 2. Lock Washer 7. Trailing Edge 3. Flat Washer 8. Mandrel As sem bly 4. Blade 5. Fünfeckige Zentrier- 1. Sechskantschraube bohrung mit Rechtsgewinde 6.
  • Page 70 5. Orifi co de centraje-es- 1. Tornillo de cabeza de cinco facetas, dextro- giro 6. Mandril-estrella de 2. Arandela elastica 7. Canto(auxiliar corta- 3. Arandela plana 4. Filo cortador 8. Nudo del mandril 1. Bullone a testa esago- 5. Foro stellare a cinque nale con fi...
  • Page 71 For best results mower blades must be kept sharp. Re place bent or damaged blades. BLADE REMOVAL • Raise mower to highest position to allow access to blades. • Remove hex bolt, lock washer and fl at washer se cur ing blade.
  • Page 72 Brakes The brakes are located inside the right rear wheel. The wheel should be dismantled for best ac cess. • Press down the clutch/brake pedal and engage the park- ing brake. Bremse Die Bremse sitzt innerhalb des rechten Hinterrades. Für beste Zugänglichkeit ist das Rad auszubauen.
  • Page 73 Dismantling of the cutting unit Work from the right side of the machine. 1. Take off the belt from the engine pulley (1). 2. Remove the two rear retainer springs (2) and knock off the axle taps with a hammer. Demontage des Mähdecks Arbeiten Sie auf der rechten Seite der Maschine.
  • Page 74 3. Remove the retainer springs (3), (4), (5) and axles. 4. Pull the lever for lifting/lowering the cutting unit back- wards. 5. Pull out the cutting unit from the machine. 3. Die Federklammern (3), (4), (5) und die jeweiligen Bolzen ausbauen.
  • Page 75 Replacement of drive belt for cutting unit 1. Dismantle the cutting unit as described previously. 2. Work off the belt from the unit's left pulley and then from the other wheels. 3. Pull the belt away from the cutting unit. 4.
  • Page 76 Adjustment of the cutting unit A. In the direction of travel 1. Check that the air pressure is correct in all four tires. 2. Make sure that the machine is on a horizontal surface. 3. Lift up the cutting unit to its highest position. 4.
  • Page 77 00598 “A” (1) Bottom edge of mower (2) Lift link adjustment nut (1) Unterkante des Mähwerks (2) Hubstangen-Stellmutter (1) Extrémités du carter de coupe (2) Ecrou de réglage du bras de suspension arrière (1) Parte inferior de la esquina de la segadora (2) Tuerca de ajuste del várillaje de levantamiento (1) Bordo inferiore del tagliaerba (2) Dado di regolazione dell'articolazione di sollevamento...
  • Page 78 Replacement of drive belt 1. Dismantle the cutting unit as described pre vi ous ly. 2. Dismantle the motion restrainer for the clutch (1). 3. Engage the parking brake and work off the belt upwards from the pulley (2), the clutch pul ley (3). 4.
  • Page 79 1. Motion Control Lever 2. Neutral Lock Gate 3. Adjustment Bolt 1. Steuerknüppel 2. Verschlussperre in Leerlaufstellung 3. Einstellbolzen 1. Levier de la commande d'avancement 2. Encoche de position neutre (N) (point mort) 3. Vis de réglage TRANSAXLE MOTION CONTROL LEVER NEU- TRAL AD JUST MENT The motion control lever has been preset at the factory and adjustment should not be nec es sary.
  • Page 80 1. Palanca de Control Del Movimento 2. Neutro Cierre Metálico 3. Perno de Regulación 1. Leva Di Comando Del Movimento 2. Blocco In Posizione Folle 3. Bullone Di Regolazione 1. Stuurbedieningshandel 2. Vrijloop-Sluitboomgrendel 3. Stelbout REGULACIÓN DE LA PALANCA DE CONTROL DEL MOVIMIENTO DEL CAMBIO MECÁNICO La palanca de control del movimiento del cambio mecánico ya viene predefi...
  • Page 81 TRANSAXLE COOLING The fan and cooling fi ns of transmission should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. • Inspect cooling fan to be sure fan blades are intact and clean.
  • Page 82 7. Troubleshooting. 7. Störungssuche. Engine will not start 1. No fuel in fuel tank. 2. Plug defective. 3. Plug connection defective. 4. Dirt in carburetor or fuel pipe. Start motor will not turn engine 1. Battery fl at. 2. Poor contact between cable and battery pole. 3.
  • Page 83 7. Recherche des pannes. 7. Búsqueda de averías. Le moteur ne démarre pas 1. Manque de carburant dans le réservoir. 2. Bougie d'allumage défectueuse. 3. Le câblage de la bougie d'allumage défectueux. 4. Il y a des impuretés dans le carburateur ou dans le circuit du carburant.
  • Page 84 7. Ricerca guasti. 7. Het localiseren van fouten. Il motore non parte 1. Manca il carburante. 2. Difetto di candela. 3. Collegamento della candela difettoso. 4. Sporco nel sistema di alimentazione e o nel carbura- tore. Il motorino di avviamento non fa girare il motore 1.
  • Page 85 8. Storage. 8. Aufbewahrung. 8. Rangement. 8. Conservación. The following steps should be taken when mowing season is over: • Clean the entire machine, especially underneath the cutting unit cover. Do not use high pressure washer for cleaning. Water can enter engine and transmission and shorten the useful life of the machine.
  • Page 86 8. Rismessaggio. 8. Stallen. Al termine della stagione effettuare i seguenti inter- venti: • Pulire tutto il tagliaerba e particolarmente sotto il co per chio della falciatrice. Per le operazioni di pulizia, non utilizzare acqua ad alta pressione. L’acqua può infi ltrarsi nel motore e nel sistema di trasmissione, riducendo quindi così...
  • Page 88 532 19 38-34 Rev. 1 12.6.04 RD Printed in U.S.A.

This manual is also suitable for:

Cth172Cth191Cth151

Table of Contents