Technical Data; Recommended Cutting Equipment For Canada - Husqvarna 340 EPA II Operator's Manual

Engine
3
Cylinder volume, cu.in/cm
Cylinder bore, inch/mm
Stroke, inch/mm
Idle speed, rpm
Power, kW/ rpm
Ignition system
Manufacture
Type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel and lubrication system
Manufacturer
Carburetor type
Fuel capacity, US pint/litre
Oil pump capacity at 9000 rpm, ml/min
Oil capacity, US pint/litre
Type of oil pump
Weight
Without bar and chain, Lbs/kg
Chain/bar
Standard bar length, inches/cm
Recommended bar lengths, inches/cm
Usable cutting length, inches/cm
Chain speed at max. power, m/sec
Pitch, inch/mm
Thickness of drive link, inch/mm
Number of teeth on drive sprocket
RECOMMENDED CUTTING EQUIPMENT
FOR CANADA
The following is a list of recommended cutting equipment for
Class 1A and 1B Chainsaws.
The combinations of powerhead, bar and chain meet all
requirements outlined in the CSA Z62.1-95 Chainsaws and
Z62.3-96 Chainsaw Kickback standards.
The guide bar nose radius is determined by either the
maximum number of teeth in the nose sprocket or the
corresponding maximum nose radius of a solid bar.
As we are listing the maximum guide bar nose radius, you
may use a guide bar with smaller nose radius than in our list.
For guide bars of the same length, all sprocket-nose guide
bars of the same pitch and having the same number of
sprocket teeth may be considered to have equivalent kick-
back energy.
A hard nose bar having the same length and nose radius as a
sprocket-nose bar may be considered to have equivalent or
less kickback energy than the sprocket-nose bar.
We recommend that you as replacement use the listed bars
and chains or "Type C Low-Kickback Saw Chains" which are
available at your dealer.
34
– English

TECHNICAL DATA

340
2,49/40,8
1,57/40
1,28/32
2 700
2,0/ 9 000
SEM
CD
NGK BPMR 7A
Champion RCJ 7Y
0,020/0,5
ZAMA
C3-EL18
1,05/0,5
9
0,53/0,25
Automatic
10,3/4,7
13"/33
13-20"/33-50
12-19"/31-49
17,3
0,325"/8,25
0,050"/1,3
0,058"/1,5
0,063"/1,6
7
Length
inch
13
15
16
18
15
16
18
20
Note: For the chains above you are free to choose between 0,050",
0,058 and 0,063" gauge drive link for the corresponding bar, see
table below.
0,050"/1,3 mm H30/95VP
0,058"/1,5 mm
0,063"/1,6 mm
345
2,75/45,0
1,65/42
1,28/32
2 700
2,2/ 9 000
SEM
CD
NGK BPMR 7A
Champion RCJ 7Y
0,020/0,5
ZAMA
C3-EL18
1,05/0,5
9
0,53/0,25
Automatic
10,3/4,7
13"/33
13-20"/33-50
12-19"/31-49
17,3
0,325"/8,25
0,050"/1,3
0,058"/1,5
0,063"/1,6
7
Guide bar Saw chain
Pitch Max nose
inch radius
0,325" 10T Husqvarna H30 or
0,325" 10T Oregon 95VP
0,325" 10T
0,325" 10T
0,325" 10T Husqvarna H25 / S24 or
0,325" 10T Oregon 21BP / 34LG or 34SL
0,325" 10T
0,325" 12T
20BP
– H25/21BP
– 22BP
350
3,15/51,7
1,77/45
1,28/32
2 700
2,3/ 9 000
SEM
CD
NGK BPMR 7A
Champion RCJ 7Y
0,020/0,5
ZAMA
C3-EL18
1,05/0,5
5-12
0,55/0,26
Automatic
10,6/4,8
13"/33
13-20"/33-50
12-19"/31-49
17,3
0,325"/8,25
0,050"/1,3
0,058"/1,5
0,063"1,6
7
33LG 33SL
34LG 34SL
35LG 35SL