Page 6
TV POWER SCHEMATIC DIAGRAM (MAIN PCB) 5A 125V CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD REPLACE ONLY WITH THE SAME TYPE 5A 125V (F501) ATTENTION: POUR LINE PROTECTION CONTINUE LES RISQUES R517_1 D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME C516 TYPE 5A 125V (F501) 500V 470P...
Page 8
AV SCHEMATIC DIAGRAM (MAIN PCB) FROM STEREO JACK FROM/TO SOUND AMP CP701B 8283_0812_00_000 C702 R727 A_IN_R A_IN_R FRONT_AUDIO_R C701 R729 A_IN_L FRONT_AUDIO_L A_IN_L FRONT_VIDEO_IN FRONT_VIDEO_IN REAR_AUDIO_R REAR_AUDIO_L AUDIO_OUT_R TO STEREO JACK AUDIO_OUT_L CP703B W808 8283_0512_00_000 L-OUT L+OUT SOUND_OUT_L R-OUT R+OUT SOUND_OUT_R P.CON+5V W814...
Page 9
STEREO JACK SCHEMATIC DIAGRAM (STEREO JACK PCB) PCB280 TO AV TE9977 F_A/V_IN(STEREO) CD701 J702_1 CH28110A JPJ3653-01-234 A_IN_R A_IN_R A_IN_L A_IN_R A_IN_L A_IN_L V_IN V_IN V_IN SPEAKER CD353 8 OHM 2.5W CH14061A SP354_1 MS-2D6SB02 SPEAKER 8 OHM 2.5W SP355_1 MS-2D6SB02 W860 FROM AV CD352 CH25088A...
Page 10
WAVEFORMS MICON/TUNER 200mV 20µs/div 12 1V 20µs/div 200mV 5ms/div 1V 20µs/div 20V 20µs/div 0.5V 20µs/div DEFLECTION/CRT 3 200mV 20µs/div 9 200mV 20µs/div 14 0.5V 5ms/div 200mV 5ms/div 0.5V 5ms/div 15 20V 20µs/div CHROMA 11 1V 20µs/div 16 2V 20µs/div 6 0.5V 20µs/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
Page 11
WAVEFORMS 200V 20µs/div 22 50V 20µs/div SOUND AMP 25 200mV 1ms/div 10V 5ms/div 26 200mV 1ms/div 10V 5ms/div 50V 20µs/div 0.5V 1ms/div 21 50V 20µs/div 1V 1ms/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
CONTENTS SERVICING NOTICES ON CHECKING ...................... A1-1 HOW TO ORDER PARTS ........................... A1-1 IMPORTANT ..............................A1-1 CONTENTS ..............................A2-1 GENERAL SPECIFICATIONS ........................A3-1~A3-4 DISASSEMBLY INSTRUCTIONS ....................... SERVICE MODE LIST ..........................CONFIRMATION OF USING HOURS ......................NOTE FOR THE REPLACING OF MEMORY IC ..................ELECTRICAL ADJUSTMENTS ........................
GENERAL SPECIFICATIONS G-1.Outline of the Product inch(508.0mmV):Measured diagonally Color CRT 90 degree deflection G-2.Broadcasting System System G-3.Color System NTSC SECAM or Monochrome signal G-4.NTSC Playback(PAL 60Hz) G-5.NTSC 3.58+4.43/PAL60Hz G-6.Antenna Input Impedance VHF/UHF 75 ohm unbalanced G-7.Tuner and Receiving Contactless Electric tuner 1Tuner System 2Tuner System channel Tuner...
Page 20
GENERAL SPECIFICATIONS G-17.Protector: Power Fuse G-18.Regulation Safety NEMKO FEMKO DEMKO IEC65 SEMKO HOMOLO SABS SISIR AS3159 DENTORI GOST NONE Radiation SABA HOMOLO CISPR13 DENTORI AS/NZS NONE X-Radiation DHHS DENTORI NONE G-19.Temperature Operation ºC~ 40 ºC Storage ºC~ 60 ºC G-20.Operating Humidity Less than G-21.Clock and Timer Sleep Timer...
Page 21
GENERAL SPECIFICATIONS G-26.OSD Language OSD Language Setting Not Applicable G-27.Speaker P o s itio n Front Side Bottom Size 6 1/3 x 2 1/4 inches Imp. ohm x Power 2.5 + 2.5 W 2.0 + 2.0 W (Typical) G-28.EXT Speaker : G-29.Carton Master Carton: Need...
Page 22
GENERAL SPECIFICATIONS G-32.Switch Front Power(Tact) Channel Up/Reset Volume Up/Set Up System Select Channel Down/Enter Volume Down/Set Down Main Power SW Sub Power Menu:Vol UP+Vol Down Rear AC/DC TV/CATV Selector Degauss Main Power SW G-33.Magnetic Field BV : +0.45G BV : +0.35G BV : +0.25G...
DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP 3. After one side is removed, pull in the opposite direction to remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 1 second. Set Key Remocon Key Operations Releasing of V-CHIP PASSWORD.
ELECTRICAL ADJUSTMENTS BEFORE MAKING ELECTRICAL 2. BASIC ADJUSTMENTS ADJUSTMENTS 2-1: RF AGC DELAY Read and perform these adjustments when repairing the Place the set with Aging Test for more than 15 minutes. circuits or replacing electrical parts or PCB assemblies. Receive an 65dB monoscope pattern.
Page 26
ELECTRICAL ADJUSTMENTS 2-9: OSD HORIZONTAL Activate the adjustment mode display of Fig. 1-1. Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-3) Fig. 2-1 00 OSD 110% Fig.
Page 27
ELECTRICAL ADJUSTMENTS PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator. minutes before performing the following adjustments.