Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Husqvarna 1153163-95
Summary of Contents for Husqvarna 1153163-95
- Page 1 Oper ator’s manual 346XP , 346XPG, 346XP E-tech 346XPG E-tech 353, 353G, 353 E-tech 353G E-tech Please r ead the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
-
Page 2: Key To Symbols
Symbols on the mac hine: W ARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. - Page 3 KEY T O SYMBOLS The chain br ake must be engaged when the chain saw is started. WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, and cause a lightning fast reverse reaction, kicking the guide bar up and towards the operator.
-
Page 4: Table Of Contents
Contents KEY TO SYMBOLS Symbols on the machine: ... 2 Symbols in the operator’s manual: ... 2 CONTENTS Contents ... 4 INTR ODUCTION Dear customer! ... 5 WHA T IS WHAT? What is what on the chain sa w? ... 6 GENERAL SAFETY PRECA UTIONS Bef ore using a new chain saw ... -
Page 5: Intr Oduction
Dear customer! Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. -
Page 6: Wha T Is What
What is what on the c hain saw? Cylinder cover Front handle Chain brake and front hand guard Starter Chain oil tank Starter handle Adjuster screws carburetor Choke control/Start throttle lock Rear handle 10 Stop switch (Ignition on/off switch.) 11 Fuel tank 12 Muffler 13 Bar tip sprocket 14 Chain... -
Page 7: General Safety Preca Utions
GENERAL SAFETY PRECA UTIONS Bef ore using a new chain saw • Please read this manual carefully. • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly. • Refuel and start the chain saw. See the instructions under the headings Fuel Handling and Starting and Stopping. -
Page 8: Personal Protective Equipment
GENERAL SAFETY PRECA UTIONS possib le. Your dealer, forestry school or your library can provide information about which training materials and courses are available. Work is constantly in progress to improve the design and technology - improvements that increase your safety and efficiency. - Page 9 GENERAL SAFETY PRECAUTIONS • The chain brake (A) can either be activated manually (by your left hand) or automatically by the inertia release mechanism. • The brake is applied when the front hand guard (B) is pushed forwards. • This movement activates a spring-loaded mechanism that tightens the brake band (C) around the engine drive system (D) (clutch drum).
-
Page 10: Chain Catcher
GENERAL SAFETY PRECAUTIONS of the front hand guard, the chain brake can only be activated by the inertia action. Will my hand always activate the chain brake during a kickback? No. It takes a certain force to move the hand guard forward. -
Page 11: Cutting Equipment
GENERAL SAFETY PRECAUTIONS chain saw, including the cutting equipment, is insulated from the handles by vibration damping units. Cutting hardwoods (most broadleaf trees) creates more vibration than cutting softwoods (most conifers). Cutting with cutting equipment that is blunt or faulty (wrong type or badly sharpened) will increase the vibration level. - Page 12 12 – English a bar and chain combinations recommended by Husqvarna. See instructions under the heading Technical Data for a list of replacement bar and chain combinations we recommend.
-
Page 13: Sharpening Your Chain And Adjusting Depth Gauge Setting
GENERAL SAFETY PRECAUTIONS • Drive link width (mm/inches) • Number of drive links. Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teeth • Never use a blunt chain. When the chain is blunt you have to exert more pressure to force the bar through the wood and the chips will be very small. -
Page 14: Tensioning The Chain
GENERAL SAFETY PRECAUTIONS one side first, then turn the chain saw and file the teeth on the other side. • File all the teeth to the same length. When the length of the cutting teeth is reduced to 5/32 inch (4 mm) the chain is worn out and should be replaced. -
Page 15: Lubricating Cutting Equipment
GENERAL SAFETY PRECAUTIONS that you can pull the chain round freely by hand and that it does not sag from the underside of the bar. The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model. - Page 16 GENERAL SAFETY PRECAUTIONS A Spur sprocket (the chain sprocket is welded on the drum) B Rim sprocket (replaceable) Regularly check the degree of wear on the drive sprocket. Replace if wear is excessive. Replace the drive sprocket whenever you replace the chain. Needle bearing lubrication Both versions of sprockets have a needle bearing on the drive shaft, which has to be greased regularly (once a...
-
Page 17: Assembly
Fitting the bar and chain WARNING! Always wear gloves, when working with the chain. Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle. Remove the bar nuts and remove the clutch cover (chain brake). -
Page 18: Fuel Handling
When working with continuous high revs (e.g. limbing) a higher octane is recommended. Environment fuel HUSQVARNA recommends the use of alkylate fuel or environmental fuel for four-stroke engines blended with two-stroke oil as set out below. Note that carburetor adjustment may be necessary when changing the type of fuel (see instructions under the heading Carburetor). -
Page 19: Fueling
• In temperatures below 32°F (0°C) some oils become too viscous. This can overload the oil pump and result in damage to the oil pump components. • Contact your service agent when choosing chain oil. Fueling WARNING! Taking the following precautions, will lessen the risk of fire: Do not smoke and do not place any hot objects in the vicinity of fuel. -
Page 20: Starting And Stopping
Starting and stopping WARNING! Note the following before starting: The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting. Never start a chain saw unless the bar, chain and all covers are fitted correctly. -
Page 21: Starting And Stopping
throttle latch in order to avoid unnecessery wear on the clutch assembly. Note! Pull the front hand guard towards the front handle. The chain brake is now disengaged. Your saw is ready for use. WARNING! Long term inhalation of the engine’s exhaust fumes, chain oil mist and dust from sawdust can represent a health risk. -
Page 22: Working Techniques
Before use: Check that the chain brake works correctly and is not damaged. Check that the rear right hand guard is not damaged. Check that the throttle lockout works correctly and is not damaged. Check that the stop switch works correctly and is not damaged. -
Page 23: General Rules
cause you to lose control. Both situations can cause serious personal injury. Before moving your chain saw switch off the engine and lock the chain using the chain brake. Carry the chain saw with the bar and chain pointing backwards. Fit a guard to the bar before transporting the chain saw or carrying it for any distance. -
Page 24: Basic Cutting Technique
In order to keep control of your saw, always maintain a firm foothold. Never work on a ladder, in a tree or on any other insecure support. Always use a fast cutting speed, i.e. full throttle. Take great care when you cut with the top edge of the bar, i.e. - Page 25 Do the conditions and surrounding terrain affect how safely you can stand and move about? Two factors decide whether the chain will jam or the object that you are cutting will split: the first is how the object is supported before and after cutting, and the second is whether it is in tension.
-
Page 26: Tree Felling Technique
Start by cutting from above (about 1/3 of the way through). Finish by cutting from below so that the two cuts meet. Tree felling technique IMPORTANT! It takes a lot of experience to fell a tree. Inexperienced users of chain saws should not fell trees. Do not attempt any task beyond your experience level! Safe distance The safe distance between a tree that is to be felled and... - Page 27 Remove any undergrowth from the base of the tree and check the area for obstacles (stones, branches, holes, etc.) so that you have a clear path of retreat when the tree starts to fall. Your path of retreat should be roughly 135 degrees away from the intended felling direction.
-
Page 28: Freeing A Tree That Has Fallen Badly
When the felling cut and directional cut are complete the tree should start to fall by itself or with the aid of a felling wedge or breaking bar. We recommend that you use a bar that is longer than the diameter of the tree, so that you can make the felling cut and directional cuts with single cutting strokes. -
Page 29: How To Avoid Kickback
If you must cut across tree/limb, make two to three cuts, one inch apart, one to two inches deep. Continue to cut deeper until tree/limb bends and tension is released. Cut tree/limb from outside the bend, after tension has been released. How to avoid kickback WARNING! Kickback can happen very suddenly and violently;... -
Page 30: Maintenance
These limit the adjustment possibilities to a maximum of a 1/2 turn. Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. Function •... -
Page 31: Checking, Maintaining And Servicing Chain Saw Safety Equipment
WARNING! Contact your servicing dealer, if the idle speed setting cannot be adjusted so that the chain stops at idle. Do not use the chain saw until it has been properly adjusted or repaired. High speed jet H At the factory the engine is adjusted at sea level. When working at a high altitude or in different weather conditions, temperatures and atmospheric humidity, it may be necessary to make minor... -
Page 32: Throttle Lockout
Checking the brake trigger Place the chain saw on firm ground and start it. Make sure the chain does not touch the ground or any other object. See the instructions under the heading Start and stop. Grasp the chain saw firmly, wrapping your fingers and thumbs around the handles. -
Page 33: Muffler
Make sure the vibration damping units are securely attached to the engine unit and handle unit. Stop switch Start the engine and make sure the engine stops when you move the stop switch to the stop setting. Muffler Never use a machine that has a faulty muffler. Regularly check that the muffler is securely attached to the machine. -
Page 34: Air Filter
recoil spring by letting the pulley rotate slowly backwards. • Undo the screw in the centre of the pulley and remove the pulley. Insert and fasten a new starter cord to the pulley. Wind approx. 3 turns of the starter cord onto the pulley. -
Page 35: Spark Plug
A damaged air filter must always be replaced. A HUSQVARNA chain saw can be equipped with different types of air filters according to working conditions, weather, season, etc. Contact your dealer for advice. -
Page 36: Cooling System
Recommended settings: Bar 13"-15": Position 1 Bar 15"-18": Position 2 Bar 18"-20": Position 3 WARNING! The engine must be stopped when making adjustments. Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: Air intake on the starter. -
Page 37: Heated Handles
• a winter plug (B) for the air nozzle that is fitted as shown. These reduce the flow of cooling air and prevent large amounts of snow from being sucked into the carburetor space. CAUTION! When the winter plug is fitted the winter flap must be open! IMPORTANT! If the temperature rises above -5°C (23°F) or 0°C (32°F) respectively the machine MUST be... -
Page 38: Maintenance Schedule
Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Daily maintenance Clean the outside of the machine. Check that the components of the throttle control work safely. -
Page 39: Technical D Ata
Technical data Motor Cylinder displacement, cu.in/cm Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Power, kW/hp @ rpm Ignition system Spark plug Electrode gap, inch/mm Fuel and lubrication system Fuel tank capacity, US pint/litre Oil pump capacity at 9,000 rpm, ml/min Oil tank capacity, US pint/litre Type of oil pump Weight... -
Page 40: Bar And Chain Combinations
Chain saw models Husqvarna 346XP and 353 met the kickback performance requirements of ANSI B 175.1-2000 when tested with the combinations of bars and saw chains listed below. The saw chain Husqvarna H30 is also classified as a low kickback saw chain since it met the requirements for low kickback saw chain outlined in ANSI B 175.1-2000. We recommend to use only the listed combinations of bars and chains for chain saw models Husqvarna 346XP and 353. -
Page 41: Federal Emission Control Warranty Statement Your Warranty Rights And Obligations
REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part will be performed at no charge to the owner at an approved Husqvarna Forest & Garden servicing dealer. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest &... -
Page 42: American Standard Safety Precautions
AMERICAN STANDARD SAFETY PRECAUTIONS Safety precautions for chain saw users (ANSI B175.1-2000 Annex C) Kickback safety precautions WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. - Page 44 Original instructions 1153163-95 ´®z+U0G¶5_¨ ´®z+U0G¶5_¨ 2010-01-26...