Husqvarna 323RJ, 325RJX-Series Operator's Manual

Husqvarna brush cutter operator's manual
Hide thumbs


Quick Links

Operator's manual (EPA)
323RJ 325RJ
Please read the operator's manual carefully and make sure you
E E E E n n n n g g g g l l l l i i i i s s s s h h h h
understand the instructions before using the machine.



  Also See for Husqvarna 323RJ, 325RJX-Series

  Related Manuals for Husqvarna 323RJ, 325RJX-Series

  Summary of Contents for Husqvarna 323RJ, 325RJX-Series

  • Page 1 Operator’s manual (EPA) 323RJ 325RJ X-series Please read the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h understand the instructions before using the machine.
  • Page 2: Key To Symbols

    Symbols WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: •...
  • Page 3: Table Of Contents

    YOUR WARRANTY RIGHTS AND OBLIGATIONS ... CONTENTS Note the following before starting: Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Maintenance, replacement, or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual.
  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS Personal protective equipment IMPORTANT! You must use approved personal protective equipment whenever you use the machine. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your dealer for help in choosing the right equipment.
  • Page 5: Cutting Equipment

    SAFETY INSTRUCTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier. Use of incorrectly wound cord or an incorrect cutting attachment increases the level of vibration. The machine ′ s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine ′...
  • Page 6: Checking, Maintaining And Servicing The Machine ' S Safety Equipment

    SAFETY INSTRUCTIONS Checking, maintaining and servicing the machine ′ ′ ′ ′ s safety equipment IMPORTANT! All servicing and repair work on the machine requires special training. This is especially true of the machine ′ s safety equipment. If your machine fails any of the checks described below you must contact your service agent.
  • Page 7 SAFETY INSTRUCTIONS • Regularly check that the muffler is securely attached to the machine. • If the muffler on your machine is fitted with a spark arrestor mesh then it should be cleaned regularly. A blocked mesh causes the engine to overheat, which can lead to serious damage.
  • Page 8: Cutting Equipment

    SAFETY INSTRUCTIONS Cutting equipment IMPORTANT! This section describes how to choose and maintain your cutting equipment in order to: Reduce the risk of blade thrust. Obtain maximum cutting performance. Extend the life of cutting equipment. Only use cutting attachments with the guards we recommend! See the chapter on Technical data.
  • Page 9: General Safety Precautions

    SAFETY INSTRUCTIONS General safety precautions IMPORTANT! The machine is only designed for trimming grass, grass clearing and/or forestry clearing. The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data. Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination.
  • Page 10: General Working Instructions

    SAFETY INSTRUCTIONS • The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage. WARNING! Take care when handling fuel. Bear in mind the risk of fire, explosion and inhaling fumes. General working instructions IMPORTANT! This section describes the basic safety precautions for...
  • Page 11 SAFETY INSTRUCTIONS Grass trimming using a trimmer head and plastic blades Trimming • Hold the trimmer head just above the ground at an angle. It is the end of the cord that does the work. Let the cord work at its own pace. Never press the cord into the area to be cut.
  • Page 12: What Is What

    What is what on the trimmer? 1 Trimmer head 2 Grease filler cap, bevel gear 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 Stop switch 9 Throttle lock 10 Cylinder cover 11 Starter handle 12 Fuel tank 13 Choke control 14 Air purge...
  • Page 13: Assembly

    Fitting the J-handle • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. • Fit the nut, knob and screw. Do not overtighten. •...
  • Page 14: Fitting The Blade Guard/Combination Guard, Grass Blade And Grass Cutter

    Fitting the blade guard/combination guard, grass blade and grass cutter • Hook the blade guard/combination guard (A) onto the fitting on the shaft and secure with the bolt. CAUTION! Use the recommended blade guard. See the Technical data section. • Fit the drive disc (B) on the output shaft.
  • Page 15: Fuel Handling

    When working at continuous high revs a higher octane rating is recommended. FUEL HANDLING Two-stroke oil • For best results and performance use HUSQVARNA two- stroke oil, which is specially formulated for our two-stroke engines. Mixture 1:50 (2%). • •...
  • Page 16: Fuelling

    Fuelling WARNING! Taking the following precautions, will lessen the risk of fire: Do not smoke or place hot objects near fuel. Always shut off the engine before refuelling. Always stop the engine and let it cool for a few minutes before refuelling. When refuelling, open the fuel cap slowly so that any excess pressure is released gently.
  • Page 17: Starting And Stopping

    STARTING AND STOPPING Check before starting For safety reasons follow these recommendations! • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth.
  • Page 18 STARTING AND STOPPING Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord.
  • Page 19: Maintenance

    Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions...
  • Page 20: Muffler

    Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops.
  • Page 21: Cooling System

    See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.
  • Page 22: Bevel Gear

    The grease in the bevel gear does not normally need to be changed except if repairs are carried out. CAUTION! Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically...
  • Page 23: Technical Data

    Technical data Engine Cylinder volume, Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Recommended max. speed, rpm Speed of output shaft, rpm Max. engine output, acc. to ISO 8893 Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, inch/mm Fuel and lubrication system...
  • Page 24: Federal Emission Control Warranty Statement

    The warranty period begins on the date small nonroad engine is delivered. LENGTH OF COVERAGE Husqvarna Forest & Garden warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years.
  • Page 25 Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 "...
  • Page 27 Trimmy H II 15 cm 6" 7,5 m ~ 3,7 m 15 cm 6"...
  • Page 28 Trimmy Hit “Click” ~ 15 cm " 15 cm 6 " 7,0 m ~ 3,5 m 12 cm 5" “Click”...
  • Page 29 Trimmy Hit Pro 15 cm 6" “Click” 7,5 m ~ 3,7 m 15 cm 6" 15 cm 6"...
  • Page 30 8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...
  • Page 31 4,25 m 4,25 m 15 cm 6" 15 cm 6"...
  • Page 32 15 cm 6" 8,5 m 10 cm 4" 4,3 m "Clic"...
  • Page 34 ´®z+H;)¶5|¨ ´®z+H;)¶5|¨...
  • Page 36 1140270-95 ´®z+H;)¶5|¨ ´®z+H;)¶5|¨ 2004-03-25...

This manual is also suitable for:

325rjx series