SVS STA-800D Quick Start Manual

SVS STA-800D Quick Start Manual

Subwoofers with sledge amplifier

Advertisement

B
S T A - 1 0 0 0 D
"WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE."
"AVERTISSEMENT:
OU DE CHOC ÉLECTRIQUE, EVITER D'EXPOSER CET APPAREIL A LA
PLUIE OU A L'HUMIDITÉ."
© 2010 SVSound, LLC
6420 Belmont Avenue, Girard, OHIO 44420
"CAUTION:
FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE, REPLACE ONLY WITH
SAME TYPE FUSE AND RATING."
"ATTENTION:
UTILISER UN FUSIBLE DE
RECHARGE DE MEME TYPE ET CALIBRE."
POUR PRÉVENIR LES RISQUES D'INCENDIE
USA 703.845.1472
Toll Free 877.626.5623
QUICK START GUIDE
SVS STA-800D/STA-1000D
A
Note: See your manual CD for a detailed owner's manual and more
1. Clear a location for your SVS powered cylinder or box subwoofer. Ensure you have an AC power
outlet ready nearby and can route an RCA interconnect (signal cable) to the sub from your AVR or pre/pro.
2. Placement: Put the subwoofer in a corner or along a wall near your seats. It is not important what
C
direction the subwoofer faces. Subs can be placed on their sides or behind furniture if required. Keep a
minimum of 4 inches clear space behind your sub to avoid pinched power cords or cables.
3. Unpack your sub. Look for gray foam "port plugs" (adjustable ported subs only) and other items which
D
might be hidden in the shipping carton. Do not discard the box and its protective inserts until necessary.
Some SVS subs are quite heavy! Please use a helper to safely move yours.
4. Connect your subwoofer: (See Owner's Guide on the included CD if using the subwoofer for bass
management) Plug your power cord into an available wall outlet. Run a single "RCA to RCA" or XLR cable
from your audio/video receiver (AVR) or preamp/processor (pre/pro) subwoofer output jack to the
subwoofer's Low Level or Balanced input jack - "A" on the diagram - (SVS subs require only one input be
connected). Switch on the sub's power when you are ready to proceed.
5. Initial subwoofer settings: Your STA-800D/STA-1000D amplifier is equipped with a digital Integrated
Function Controller that allows access to the amplifier's controls via a single knob and LCD screen - "B" on the
diagram. The default values from the factory (see Owner's Guide on the enclosed CD for details) are correct
for systems with bass management performed in the AVR or pre/pro. If using the subwoofer for bass
management and/or optionally time alignment, see the Owner's Guide for proper configuration. If using an
AVR or pre/pro with consumer level voltage levels, set the "Input Level" switch - "C" on the diagram - to
"Normal", otherwise set it to "Hi Level". Set the "Auto/On" switch - "D" on the diagram - to "On" if you
want the sub on all the time, otherwise set it to "Auto".
6. Initial AVR or pre/pro settings: If your AVR or pre/pro has an auto setup feature, run it now.
Afterwards, check your speakers are set to "Small" and the crossover is at 80Hz. For non-auto setup AVRs,
ensure your speakers and subwoofer are enabled for use. If adjustable, make sure your speakers are set to
"Small" and the crossover for all speakers is set to 80Hz or higher if needed.
7. Channel Level Matching: If you have run auto setup on your AVR or pre/pro, you are done since this
step has already been performed. The key to good sound is having all your channels at the same level. Use
a sound pressure level (SPL) meter set to "slow" and "C-weighting". Play your AVR's calibration test tones
or the AVIA test DVD so tones are cycled to each speaker. This allows you to use each channel's individual
level controls to achieve a measured 75 dB for each speaker. Set channels to 85 dB if using AVIA.
sales@svsound.com
© 2010 SVSound, LLC
Subwoofers Equipped with
Sledge
Amplifier
setup details concerning your new subwoofer.
6420 Belmont Avenue, Girard, OHIO 44420
USA 703.845.1472
Toll Free 877.626.5623
sales@svsound.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the STA-800D and is the answer not in the manual?

Questions and answers

Summary of Contents for SVS STA-800D

  • Page 1 (AVR) or preamp/processor (pre/pro) subwoofer output jack to the subwoofer’s Low Level or Balanced input jack - “A” on the diagram - (SVS subs require only one input be connected). Switch on the sub’s power when you are ready to proceed.
  • Page 2 SV Sound, LLC SV Sound, LLC 800D &1000D Quick Start Guide 800D &1000D Quick Start Guide Important Safety Instructions Important Safety Instructions 1. Read these instructions. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 2.

This manual is also suitable for:

Sta-1000d

Table of Contents