Furnace Specifications - Amana 40" Technical Information

FURNACE SPECIFICATIONS

MODEL
Btuh Input (US)
Output (US)
A.F.U.E.
Rated External Static (" w.c.)
Temperature Rise (°F)
Pressure Switch Trip Point (" w.c.)
Blower Wheel (D" x W")
Blower Horsepower
Blower Speeds
Max CFM @ 0.5 E.S.P.
Power Supply
Minimum Circuit Ampacity (MCA)
Maximum Overcurrent Device
Transformer (VA)
Heat Anticipator
Primary Limit Setting (°F)
Auxiliary Limit Setting (°F)
Rollout Limit Setting (°F)
Fan Delay On
Off Heating *
Off Cooling
Gas Supply Pressure (Natural/Propane) ("w.c.)
Manifold Pressure (Natural/Propane) ("w.c.)
Orifice Size (Natural/Propane)
Number of Burners
Vent Connector Diameter (inches)
Shipping Weight (lbs.)
* Off Heating - This fan delay timing is adjustable (60, 90, 120 or 180 seconds), 90 seconds as shipped.
*150 = The GUID090**30 furnaces were changed from primary limit part #10728331 (160°F) to limit part #10728332 (150°F) per ECN60850 effective June 6, 2000.
1. These furnaces are manufactured for natural gas operation. Optional kits are available for conversion to propane opera-
tion.
2. For elevations above 2000 ft. the rating should be reduced by 4% for each 1000 ft. above sea level. The furnace must not
be derated, orifice changes should only be made if necessary for altitude.
3. The total heat loss from the structure as expressed in TOTAL BTU/HR must be calculated by the manufacturers
method or in accordance with the "A.S.H.R.A.E. GUIDE" or "MANUAL J-LOAD CALCULATIONS" published by the AIR
CONDITIONING CONTRACTORS OF AMERICA. The total heat loss calculated should be equal to or less than the
heating capacity. Output based on D.O.E. test procedures, steady state efficiency times output.
4. Minimum Circuit Ampacity calculated as: (1.25 x Circulator Blower Amps) + I.D. Blower Amps.
8
Rev. 1
GUID045CA30 GUID070CA30
GUID045CX30 GUID070CX30
GUID045DA30 GUID070DA30
GUID045DX30 GUID070DX30
46,000 69,000
36,800 55,200
80% 80%
.10 - .50 .12 - .50
35 - 65 35 - 65
-0.55 -0.55
9 x 8 9 x 8
1/3 1/3
4 4
1200 1290
115-60-1 115-60-1
8.6 8.5
15 15
40 40
0.7 0.7
230 220
160 160
250 300
30 secs. 30 secs.
90 secs. 90 secs.
45 secs. 45 secs.
11-Jul 11-Jul
3.5 / 10 3.5 / 10
#43 / #55 #43 / #55
2 3
4 4
140 151
GUID070CA40
GUID090CA30
GUID070CX40
GUID090CX30
GUID070DA40
GUID090DA30
GUID070DX40
69,000 92,000
55,200 73,600
80% 80%
.12 - .50 .15 - .50
35 - 65 40 - 70
-0.55 -0.55
10 x 6 10 x 8
1/2 1/2
4 4
1529 1380
115-60-1 115-60-1
10.4 8.2
15 15
40 40
0.7 0.7
170 *150
160 160
300 300
30 secs. 30 secs.
90 secs. 90 secs.
45 secs. 45 secs.
11-Jul 11-Jul
3.5 / 10 3.5 / 10
#43 / #55 #43 / #55
3 4
4 4
152 169
GUID090CA50 GUID115CA50
GUID090CX50 GUID115CX50
GUID090DA50 GUID115DA50
GUID090DX50 GUID115DX50
92,000 115,000
73,600 92,000
80% 80%
.15 - .50 .20 - .50
40 - 70 40 - 70
-0.55 -0.55
10 x 8 10 x 9
3/4 3/4
4 4
1975 1985
115-60-1 115-60-1
14.6 13.1
15 15
40 40
0.7 0.7
160 190
160 160
300 275
30 secs. 30 secs.
90 secs. 90 secs.
45 secs. 45 secs.
11-Jul 11-Jul
3.5 / 10 3.5 / 10
#43 / #55 #43 / #55
4 5
4 4
178 194