1. Manuals
  2. Brands
  3. VuQube Manuals
  4. Satellite TV System
  5. V20
  6. Installation and operating instructions manual

VuQube V20 Installation And Operating Instructions Manual

Automatic satellite system with built-in dvb for positive satellite identification
Hide thumbs Also See for V20:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Installation Instructions and Operating Manual
Automatic Satellite System
with built-in DVB for positive satellite identification
Model V20
Installation and Operating Instructions
®
Satellite Solutions for Mobile Markets
11200 Hampshire Avenue South, Bloomington, MN 55438-2453
Phone: (800) 982-9920
Fax: (952) 922-8424
www.kingcontrols.com
20625 REV B

Advertisement

Table of Contents
loading

Related Manuals for VuQube V20

Summary of Contents for VuQube V20

  • Page 1 Automatic Satellite System with built-in DVB for positive satellite identification Model V20 Installation and Operating Instructions ® Satellite Solutions for Mobile Markets 11200 Hampshire Avenue South, Bloomington, MN 55438-2453 Phone: (800) 982-9920 Fax: (952) 922-8424 www.kingcontrols.com 20625 REV B...

  • Page 3: Table Of Contents

    The satellite TV market is expanding and changing. The information in this manual was accurate at the time of printing. If your VuQube does not operate as outlined in this manual please call King Controls at (800) 982-9920 or visit our website at www.kingcontrols.com.

  • Page 4: Introduction

    INTRODUCTION SECTION 1 The VuQube V20 Automatic Satellite System provides simple, one-touch operation for easy access to all your favorite satellite TV channels. It is a full featured dish system with automatic satellite acquisition and satellite switching capabilities. The V20 is compatible with the following satellite services: ®...

  • Page 5: Installation

    INSTALLATION SECTION 2 TOOLS AND MATERIALS REQUIRED: 1. Read thru the instructions and make sure you have all the tools and materials required to complete the installation, including: • mounting bracket (sold separately - for more information call King Controls at 800-982-9920 or visit our website at www.kingcontrols.com) •...
  • Page 6 IMPORTANT! The antenna unit MUST be mounted to the air ride cab, NEVER to any structure mounted directly to the frame (for example the headache rack). Mounting directly to the frame will void the VuQube warranty. 3. Determine the location of the antenna unit using the following criteria:...
  • Page 7 (Fig. 4). Note: The VuQube is wired for a dual LNB. There are two coax ports on the back of the antenna unit. The one labeled “MAIN” MUST be connected to the main receiver in vehicle. This is the receiver that will control automatic satellite switching if applicable.
  • Page 8 7. Run wiring from the antenna unit to the location where it will be fed into the vehicle. Make sure external wiring is tied down securely (to a hand rail for example) (Fig. 5). 8. Drill 3/4” hole through the cab or use an existing hole to feed the wiring inside the cab. Seal opening with cab compatible sealant so that it is entirely waterproof (inside and outside of the hole).
  • Page 9 INTERNAL WIRING 9. Inside the vehicle, make the connections as shown in (Fig. 6), keeping in mind the following important points: a) The connection between the antenna unit and the receiver must be a direct connection with no devices in between. b) Power connection must be a non-shared circuit.
  • Page 10 This page intentionally left blank. Page 8...

  • Page 11: Vuqube Antenna Configuration

    Network or ExpressVu programming, you must use the VuQube hand held controller to re-configure the antenna to work with your satellite service. Doing this will allow the VuQube to lock on the correct satellites to receive your programming and also enable automatic satellite switching via the receiver’s remote control for multi-satellite service.

  • Page 12: Single Satellite 101 (Factory Pre-Set)

    DIRECTV ANTENNA CONFIGURATION Single Satellite 101 The VuQube is factory pre-set for the DIRECTV 101 satellite. Unless the antenna has been configured for another option since leaving the factory, PERFORM STEP 5 ONLY. 1. On the VuQube controller, press and release the ON button.

  • Page 13: Dish Network

    DISH NETWORK ANTENNA CONFIGURATION Single Satellite 119 1. On the VuQube controller, press and release the ON button. Wait for the status light to flash orange, and then flash green or red. 2. Press and release the ON button 20 times.

  • Page 14: Dish 1000 - Hdtv

    129 in the western U.S. The map below shows the approximate coverage for each satellite. Your VuQube antenna can be easily configured to work with two different satellite trios (DISH 1000a: 61,110,119 or DISH 1000: 110,119,129). By choosing the appropriate trio that includes either the 61 or the 129 satellite based on where you are, you can receive all of your desired programming.
  • Page 15 DISH NETWORK ANTENNA CONFIGURATION-continued DISH 1000 HD (satellites 110, 119, 129) 1. On the VuQube controller, press and release the ON button. Wait for the status light to flash orange, and then flash green or red. 2. Press and release the ON button 20 times.

  • Page 16: Bell Expressvu

    BELL EXPRESSVU ANTENNA CONFIGURATION Standard Digital (satellite 91) 1. On the VuQube controller, press and release the ON button. Wait for the status light to flash orange, and then flash green or red. 2. Press and release the ON button 8 times.
  • Page 17 This page intentionally left blank. Page 15...

  • Page 18: Satellite Receiver Configuration

    (Dish 1000/1000a only). 1. Turn on the TV and satellite receiver. 2. On the VuQube controller, press and hold the ON button for 3 FULL SECONDS.
  • Page 19 The unit will perform a check switch test, and the dish will periodically move back and forth. (This process will take several minutes.) 7. When test is complete, a screen similar to one of the following should appear: DISH 500 BELL EXPRESSVU MUST SHOW “SW21”...

  • Page 20: Operation

    3. When the status light is steady green, select a channel or the program guide to view your programming. Enjoy! (DO NOT TURN THE VUQUBE OFF IF USING THE AUTOMATIC SATELLITE SWITCHING FEATURE.) Note: If the status light is steady GREEN and your programming does not appear, press the reset button on your DIRECTV receiver.
  • Page 21 AUTOMATIC SATELLITE SWITCHING 1. After you have properly configured the VuQube antenna for your satellite service, the VuQube will automatically switch between satellites by simply selecting your desired channel using the receiver’s remote control. Note: For better performance when using the automatic satellite switching feature, change channels by selecting your program from the channel guide rather than channel surfing.
  • Page 22 129 in the western U.S. The map below shows the approximate coverage for each satellite. Your VuQube antenna can be easily configured to work with two different satellites trios (DISH 1000a: 61,110,119 or DISH 1000: 110,119,129) as you travel from one coverage area to another.
  • Page 23 61, 110, 119 TRIO (DISH 1000a) 1. On the VuQube controller, press and release the ON button. Wait for the status light to flash orange, and then flash green or red. 2. Press and release the ON button 4 times.
  • Page 24 CHANGE SEARCH ELEVATION If you have traveled a long distance since last performing a search, you can speed up acquisition time by setting the VuQube to start searching at one of four different elevations: 25°, 37°, 48° or 55°. Find your location on the appropriate map for your service and choose the elevation closest to you.
  • Page 25 CHANGE SEARCH ELEVATION TO 25° 1. On the VuQube controller, press and release the ON button. Wait for the status light to flash orange, and then flash green or red. 2. Press and release the ON button 8 times. The status light starts rapidly flashing green and red.
  • Page 26 CHANGE SEARCH ELEVATION-Continued CHANGE SEARCH ELEVATION TO 48° 1. On the VuQube controller, press and release the ON button. Wait for the status light to flash orange, and then flash green or red. 2. Press and release the ON button 16 times.

  • Page 27: Troubleshooting

    TROUBLESHOOTING SECTION 6 SYMPTOM POSSIBLE REASON COURSE OF ACTION VuQube does not find satellite. Did not hold ON button for Hold ON button for 3 FULL (STATUS light flashes red or green.) 3 FULL SECONDS. SECONDS. STATUS light flashes orange.

  • Page 28: Maintenance

    Periodic washing of the enclosure with mild soap and water is recommended. If you plan on not using your VuQube for long periods of time, it is recommended that the system be put through a search procedure on a quarterly basis to keep all moving parts in good working order.

  • Page 29: Limited Warranty

    LIMITED WARRANTY SECTION 8 Every VuQube Satellite System is thoroughly inspected and tested before leaving the factory. It is covered by a one year parts limited warranty from the date of original purchase. This warranty does not cover installation and external wiring or refurbished units.
  • Page 30 Notes: Page 28...
  • Page 32 11200 Hampshire Avenue South, Bloomington, MN 55438-2453 Phone: (800) 982-9920 Fax: (952) 922-8424 www.kingcontrols.com ®...

Table of Contents