Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kingrex SLAP
Summary of Contents for Kingrex SLAP
- Page 1 ANUAL ANUAL...
-
Page 2: Table Of Contents
Warranty card *1 Introduction SLAP is designed with automatic monitoring by TI UC3906IC which is a SLA battery charger controller. It is using 3 stage charging management to prevent overcharging and this design could extend the life of SLA battery. -
Page 3: Specification
Specification Rated input voltage AC 90~260V, 47~67Hz Battery type 12 volt nominal SLA Battery size 12V/7Ah Charging current 80mA~ 750mA Charging type Lead Acid Chemistry Constant current/ constant voltage/float Stage 1: current 750mA Stage 2: current 400mA Charging current Stage 3: float charge current 200~400mA “Charged”... -
Page 4: Design Consideration Of Kingrex Slap
We believe these two products match most audiophile demands because of their reasonable price and excellent quality but also they sound good. Nevertheless, to satisfy the highest level of audiophile expectation for low noise and distortion, we have developed a pure power source – the SLAP (Sealed Lead-Acid battery power supply unit) What are the differences between switching power, linear power, and battery power? All amplifiers need a continuous current supply during operation. - Page 5 The battery power supply provides the required current for operation while maintaining a very large reserve for transient and bass heavy passages. The SLAP uses YUASA NP7-12 (12V/7AH) sealed lead-acid battery which has a maximum output of 105A w/o pulse noise which is a very good match for the under 20 Watt output of Class T or...
- Page 6 10.5V protecting the amplifier from low voltage situations. Operation of the SLAP is very user friendly. Users only need to press one button for automatic operation of all functions. Charging and discharging status are shown by one dual color LED light.
-
Page 7: Key Features
6mm thick aluminum face plate. The stylish design stable platform will provide the user with a reliable product for years to come. All the components used in SLAP are of the highest quality and have been selected through intensive listening sessions. -
Page 8: Important Safety Instruction
Please read this user manual very carefully. It provides safety, installation, and operating instructions that will help you derive the over all performance and fully extend the life that the SLAP has to offer. Please save this manual! It includes important instructions for the safely use SLAP and for obtaining factory service should the proper operation of the SLAP come into question. -
Page 9: Operation Environment Presentation
Operation environment presentation FRONT PANEL States indicator (RED/GREEN DOUBLE COLOUR LED) Charging stage : (CHARGER ON , PSU ON) a. Red - Charging A 7Ah SLA battery could be fully charged after 24hours charging. But it should depend on individual one status. -
Page 10: Rear Panel
Operation environment presentation REAR PANEL AC POWER INPUT: FROM:90-260V AC 47-63HZ CHARGER ON SWITCH: ENABLE SLAP TO CHARGE MODE PSU ON SWITCH: ENABLE SALP DC OUTPUT ON AC FUSE SLOT: 2A/250V FUSE FUSE FOR DC OUTPUT: 3A/250V DC OUTPUT: BATTERY DC POWER OUTPUT PSU ON, CHARGER ON >>>>>DC OUT OFF... -
Page 11: Installation
Connect the loads Plug the loads(Amplifier) into the DC output connectors on the rear of the SLAP. To use the SLAP as a PSU ON switch, make sure all of the loads are switched on). USE KINGREX DC CABLE ONLY !!! -
Page 12: Operating Method
Switch on With SLAP plugged in, press and PSU On then DC output , when Battery low to 10.5V, DC output will auto cut off and front panel LED light will flashing green & read lights. For protect Battery not into deep discharging (Deep discharging will damage the SLA battery. -
Page 13: Troubleshooting
Trouble Shooting Storage Storage conditions Store the SLAP covered and upright in a cool, dry location, with its battery fully charged. Before storing, charger the SLAP for at least 15 hours Extended storage During extended storage in environments where the ambient temperature is -15 to +30 (+5 to +86 ), charge the SLAP’s battery every 6 months. -
Page 14: Maintenance
Service The simplicity of the KingRex SLAP is very few parts can be breaking down. Should you ever require service, you can either contact your dealer or national distributor, who can solve any problems locally. You are also very welcome to contact KingRex Technology Co., LTD directly if you need any information or help. - Page 15 COMPANY NO. Empty or alter content of warranty, cannot recognize content of warranty certification. PURCHASE DATE Client Information Name KINGREX TECHNOLOGY CO., LTD Address 2F, NO.232 LIANCHENG RD.,JHONGHE CITY,TAIPEI TAIWAN 235 -14-...