Advertisement
Operation Guide 5033
Alarms
The Alarm Mode gives you a choice of four one-time
Alarm number
alarms and one snooze alarm.
Also use the Alarm Mode to turn the Hourly Time Signal
(SIG) on and off.
• There are five alarms numbered AL1 through AL4,
and SNZ. You can configure SNZ as a snooze
alarm only. Alarms AL1 through AL4 can be used
as one-time alarms only.
• Alarm settings (and Hourly Time Signal settings) are
Alarm time
available in the Alarm Mode, which you enter by
pressing C.
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
Snooze indicator
screens until the one whose time you want to set is
displayed.
AL1
SIG
2. After you select an alarm, hold down A until the hour
Alarm on indicator
setting of the alarm time starts to flash, which indicates
the setting screen.
• This operation automatically turns on the alarm.
3. Use C to move the flashing in the sequence shown
below to select other settings.
Hour
4. While a setting is flashing, use D and B to change it.
• While the hour or minute setting is flashing, use D (+) and B (–) to change it.
5. Press A to exit the setting screen.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off.
• Pressing any button stops the alarm tone operation.
• If any alarm operation (one-time alarm, snooze) occurs while a signal receive
operation is in progress, the receive operation will be canceled.
• Displaying the Timekeeping Mode setting screen during a 5-minute interval between
snooze alarms will stop the current snooze alarm operation (but snooze alarm will
remain as the alarm type setting).
• The snooze indicator flashes during the 5-minute intervals between alarms.
• The alarm on indicator and snooze indicator are displayed in all modes.
• In all modes, the alarm on indicator is shown for any alarm that is currently turned
on.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn an alarm on and off
1. In the Alarm Mode, use D to scroll through the alarm
Alarm on indicator
screens until the one whose time you want to set is
displayed.
2. Press A to toggle it on (ON) and off (OF).
On/Off status
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to scroll through the alarm
Hourly time signal
screens until the Hourly Time Signal screen (
on indicator
displayed.
2. Press A to toggle it on (ON) and off (OF).
• The Hourly Time Signal on indicator is displayed in all
modes when the Hourly Time Signal is turned on.
On/Off status
Stopwatch
The stopwatch lets you measure elapsed time, split times,
Split indicator
and two finishes.
• The display range of the stopwatch is 59 minutes, 59.99
seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
1/100 second
Seconds
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
Minutes
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
AL2
AL3
SNZ
AL4
Minutes
SIG
) is
To measure times with the stopwatch
Elapsed Time
D
➤
D
➤
D
Start
Stop
Re-start
Split Time
D
➤
A
➤
A
Start
Split
Split release
(Split indicator
displayed)
Two Finishes
D
A
➤
D
➤
Start
Split
Stop
First runner
Second runner
finishes.
finishes.
Display time of
first runner.
Countdown Timer
The countdown timer can be set within a range of 1 minute
to 24 hours. An alarm sounds when the countdown
reaches zero.
• Calibration signal reception (both auto and manual) is
disabled while a countdown timer operation is in
progress.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
Seconds
C.
Minutes
To set the countdown start time
1. While the countdown start time is on the display in the Countdown Timer Mode,
hold down A until the current countdown start time starts to flash, which indicates
the setting screen.
• If the countdown start time is not displayed, use the procedure under "To use the
countdown timer" to display it.
2. Press C to move the flashing between the hour and minute settings.
3. While a setting is flashing, use D (+) and B (–) to change it.
• To set the starting value of the countdown time to 24 hours, set 0:00.
4. Press A to exit the setting screen.
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button. The countdown time will be reset
automatically to its starting value after the alarm stops.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To stop a countdown operation completely, first pause it (by pressing D), and then
press A . This returns the countdown time to its starting value.
Timekeeping
Use the Timekeeping Mode to set and view the current time and date. This section
also explains how to set the current date and time manually.
• When setting the time, you also can configure settings for the day of the week
language and the 12/24-hour format.
• All of the operations in this section are performed in the Timekeeping Mode, which
you can enter by pressing C.
• In the Timekeeping Mode, you can press A to toggle the display contents as shown
below.
Day of week
Press A.
Second
Day
Month
• Pressing D in the Timekeeping Mode will display the Last Signal screen.
Day of week
Press D.
Second
Day
Month
Setting the Digital Time and Date Manually
Make sure you select your Home City code before you change the current time and
date settings. World Time Mode times are all displayed in accordance with the
Timekeeping Mode settings. Because of this, World Time Mode times will not be
correct if you do not select the proper Home City code before setting the time and
date in the Timekeeping Mode.
To set the current digital time and date manually
1. In the Timekeeping Mode, hold down A until the city
City code
code starts to flash, which indicates the setting screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
12/24-Hour
City Code
DST
Format
Language
Day
Month
• The currently selected language indicator flashes on the display while the
Language (setting) is selected in the above sequence.
➤
A
➤
D
Stop
Clear
➤
D
➤
A
Stop
Clear
➤
A
➤
A
Split release
Clear
Display time of
second runner.
Day of week
PM indicator
Minutes
Hour
Last Signal Screen
Receive time
Receive date
Seconds
Hour
Year
Minutes
3
Hide quick links:
Advertisement
