Record Power AC400 Original Instruction Manual page 6

General Health & Safety Guidance
16. Avoid unintentional starting of the machine
• Most machines are fitted with a no-volt release (NVR)
switch to prevent unintentional starting. If in doubt
always ensure the machine switch is in the 'OFF' position
before connecting it to the power supply. This means the
machine will not automatically start up after a power
cut or switching on of the power supply, unless you first
reset the start switch.
17. Outdoor use
• Your machine should not be used outdoors.
18. Extension cables
• Whenever possible, the use of extension cables is
not recommended. If the use of an extension cable is
unavoidable, then it should have a minimum core cross
section of 2.5mm² and limited to a maximum length of
3 metres.
• Extension cables should be routed away from the direct
working area to prevent a trip hazard.
19. Guard against electric shock
• Avoid body contact with earthed or grounded surfaces
such as pipes and radiators. There is an increased risk of
electric shock if your body is earthed or grounded.
20. Always work within the machine's intended
capacities
• Operator safety and machine performance are seriously
adversely affected if attempts to make the machine
perform beyond its limits are made.
21. Do not abuse the power cable
• Never pull the power cable to disconnect it from the
power socket. Always use the plug.
• Keep the power cable away from heat, oil and
sharp edges.
• Do not use the power cable for carrying or moving
the machine.
22. Secure the work piece
• Ensure that the work piece is securely held before
starting to machine it.
• When working within 300 mm of the machining area,
always use a push stick to feed the work piece in to
the blade or cutting tool. The push stick should have a
minimum length of 400 mm. If the push stick becomes
damaged, replace it immediately.
• Use extra supports (roller support stands etc.) for any
work pieces large enough to tip when not held down to
the table top.
• Do not use another person as a substitute for a table
extension, or as additional support for a work piece that
6
is longer or wider than the basic table, or to help feed,
support, or pull the work piece.
• Do not attempt to machine more than one work piece at
a time.
• When feeding the work piece towards the blade or
cutting tool never position your hands in direct line of
the cutting path. Avoid awkward operations and hand
positions where a sudden slip could cause your hand or
fingers to move into the machining area.
23. Stay alert
• Safety is a combination of operator common sense and
alertness at all times when the machine is being used.
• Use all machines with extreme care and do not use the
machine when you are tired or under the influence of
drugs, alcohol or medication.
24. Use the correct tool for the job
• Do not use the machine for any purpose other than
which it was designed.
• When selecting replacement cutting tools and blades,
always ensure that they are designed to cut the material
that you intend to use them for. If in any doubt seek
further advice from the manufacturer.
25. Connect dust extraction equipment
• Always use dust extraction equipment. The dust extractor
should be of suitable size and capacity for the machine
that it is connected to and have a filtration level
appropriate to the type of waste being collected. Refer
to the relevant section of the manual for details of the
specific dust extraction requirements for this machine.
• The dust extractor should be switched 'ON' before
starting the machine that it is connected to. The dust
extractor should be left running for 30 seconds after the
last machining operation is complete in order to clear
any residual waste from the machine.
26. Ensure that the machine is correctly guarded
• Never use the machine if any of the standard safety
guards and equipment are removed or damaged.
• Some machines incorporate safety interlocks to prevent
the machine from being used without the guards in
place. Never attempt to bypass or modify the interlocks
to allow the machine to be used without the guards
in place.
27. Maintain your machine with care
• This manual gives clear instructions on installation, set
up and operation of the machine and also details any
routine and preventative maintenance that should be
performed periodically by the user.
Original Instruction Manual | AC400 Air Cleaner | Version 3.0 | November 2012