Table of Contents
Advertisement
T-2 Integrated Vacuum Tube Amplifier
Please read this OWNER'S MANUAL before operating your new
laboratories
T-2
electrical shocks or equipment failure due to improper installation!
WELCOME & THANK YOU
OWNERS MANUAL
neuhaus
laboratories
012110
amplifier. Observe the Safety Instructions to avoid
neuhaus
Advertisement
Table of Contents
Summary of Contents for neuhaus laboratories T-2
-
Page 1: Owners Manual
OWNERS MANUAL neuhaus laboratories T-2 Integrated Vacuum Tube Amplifier 012110 Please read this OWNER'S MANUAL before operating your new neuhaus laboratories amplifier. Observe the Safety Instructions to avoid electrical shocks or equipment failure due to improper installation! WELCOME & THANK YOU... -
Page 2: Important Safety Instructions
• Do not drop unit, apply excessive force to the controls or place heavy objects on top of the unit. • Do not allow excessive levels of dust to gather on the T-2. To clean, unplug the cooled unit, use a soft dry cloth. If necessary, use a damp cloth without any... - Page 3 • Ensure that the unit is connected to the correct power supply as indicated on the unit. Unplug the T-2 when not in use for a long period. Always make sure power cables are placed safely and are not obstructing a walkway.
-
Page 4: Speaker Connection
UNPACKING Before unpacking, check if there is any damage to the carton. Place on a flat surface with the arrow upward. Carefully remove your new amplifier and all accessories from its packing carton, and examine it closely for signs of shipping damage. -
Page 5: Computer Connection
COMPUTER CONNECTION If you plan to use the amplifier with your computer, connect the USB cable supplied with the unit from your computer to the USB input on the back of the amplifier. POWER CORD Connect the power cord: first be sure to set the "VOLUME" control to the lowest position and the power switch in the “OFF”... - Page 6 The sound level can be adjusted from the “speaker bar” on your computer and should be placed at maximum so main volume is controlled by the T-2 amp. MAC OPERATING SYSTEMS MAC COMPATIBLE Plug the USB cable into the USB port of your Mac computer. Select “Sound” in System Preferences.
- Page 7 OPTICAL SYSTEM CONNECTION Most Apple Mac computers allow optical connection directly from the computer to the neuhaus laboratories T-2 amplifier. Optical cable, included (Toslink cable with Mini Headphone plug adapter). Plug the square toslink connector to the rear of the amplifier and the plug connection to the mini headphone port of the Mac.
- Page 8 CD Player Connect CD Player (CD) to rear panel Left (White) and Right (Red). Select CD on selector switch. Connect Turntable (AUX) (Phono Pre-Amp required) to rear panel Left (White) and Right (Red). Select AUX on selector switch. TUNER Connect Tuner (TUN) to rear panel Left (White) and Right (Red). Select TUN on selector switch.
-
Page 9: Tube Biasing
BURN-IN While the amplifier should sound fine straight out of the box, you may notice that your amplifier needs a period of “burn-in" before it sounds optimal. Your unit should be considered adequately burned-in after the first 50 hours of use. TUBE BIASING neuhaus laboratories... - Page 10 OUTPUT OUTPUT POWER TRANSFORMER TRANSFORMER TRANSFORMER WARRANTY Our products are individually tested at the factory and meet our specifications before being packed and sent to you. Products sold by neuhaus laboratories or its authorized dealers are covered by a limited one year labor and parts warranty [excluding vacuum tubes] counted from the shipping date protecting you against defects in materials and workmanship.
-
Page 11: Specifications
FOR ANY PARTICULAR PURPOSE, EXCEPT IN JURISDICTIONS THAT PROHIBIT SUCH DISCLAIMERS OF IMPLIED WARRANTIES. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE. Specifications T-2 is a true Push Pull Vacuum Tube Amplifier (not solid state). Output- 20W x 2 Frequency Response-10-30KHZ Output Impedance-4ohm-8ohm Harmonic Distortion-1.5%(1KHZ)