Assembling The Blades; Installing The Canopy - Hunter Ceiling fan Installation And Operation Manual

6 6 6 6 6
Wall Switch Wire for Separate
Control of Light Fixture
Power
Black
Wires
in White
Ceiling
Bare or Green
2 x 4 Brace
Approved
Connectors
Green Ground Wire from
Hanger Pipe (not present
with flush mounting
option)
F F F F F i i i i i g g g g g ur ur ur ur ure 12 - W e 12 - Wir ir ir ir irin in in in ing t e 12 - W e 12 - W e 12 - W

installing the canopy

1. Rotate the fan 180º clockwise from the initial position when
hanging the fan. The arrows on the hanger ball and on the
ceiling plate should be pointing in the same direction and
should be pointing towards the tab hole on the canopy. Refer
to Figure 13.
F F F F F i i i i i g g g g g ur ur ur ur ure 13 - R e 13 - R e 13 - R e 13 - Ro o o o o t t t t t a a a a a t t t t t in in in in ing t
e 13 - R
2. Hook the tab hole over the tab on the ceiling plate as shown in
Figure 14.
3. Raise the canopy, be sure the holes in the canopy and the ceil-
ing plate are aligned, and loosely assemble the canopy screws
one at a time. When all three screws are assembled, securely
tighten all three canopy screws. Refer to Figure 14.
41826-01 01/14/2003
(Note: Wall
switch must be
acceptable as a
general-use
switch.)
Outlet Box
Ceiling Plate
Connections:
1
1. Connect Blk/Wht
2
wire from the fan to the
wall switch for separate
Blk/Wht
control of the light
3 Wires
fixture, or
from Fan
2. Connect Blk/Wht
wire from the fan to the
ceiling black wire if there
is no separate wall
switch wire for the light
fixture.
g th h h h h e f e f e f e f e fa a a a a n n n n n g t g t g t
g t g t g t g th h h h h e f e f e f e f e fa a a a a n n n n n
Tab Hole
and Tab
Canopy
Screw
F F F F F i i i i i g g g g g ur ur ur ur ure 14 - I e 14 - I e 14 - In n n n n s s s s s t t t t t a a a a a llin e 14 - I
e 14 - I

assembling the blades

Hunter fans use several styles of fan blade irons (brackets that hold
the blade to the fan).
1. Your fan may include blade grommets. If your fan has grom-
mets, insert them by hand into the holes on the blades as shown
in Figure 15.
F F F F F i i i i i g g g g g ur ur ur ur ure 15 - I e 15 - I e 15 - In n n n n s s s s s e e e e e r r r r r t t t t t in in in in ing t e 15 - I g t g t g t g th h h h h e g e g e g e gr r r r r o o o o o mm
e 15 - I e g
2. Attach each blade to blade iron using three blade assembly
screws as shown in Figure 16. Some fans feature a decorative
medallion as well as a blade iron. Insert the assembly screws
into the blade iron, through the blade and into the medallion,
with the blade sandwiched between the blade iron and me-
dallion as shown in Figure 17.
F F F F F i i i i i g g g g g ur ur ur ur ure 16 - A e 16 - A e 16 - A e 16 - At t t t t t t t t t a a a a a c c c c c h h h h h in in in in ing t g th h h h h e b g t g t g t
e 16 - A
llin llin g t g th h h h h e c g t g t e c e ca a a a a n n n n n o o o o o p p p p p y y y y y e c
lling t llin e c
Grommet
Fan Blade
mm mm mme e e e e t t t t t s in s int t t t t o t s in s in o t o t o th h h h h e f e f e f e f e fa a a a a n b n b n bl l l l l a a a a a d d d d d e e e e e s s s s s n b
mm s in o t n b
e b e b e bl l l l l a a a a a d d d d d e t e t e t e t e to t o t o th h h h h e b o t e bl l l l l a a a a a d d d d d e ir e b e b e iro o o o o n n n n n e ir e ir
e b o t e b e ir
© 2003 Hunter Fan Company