Parts List (Nozzle Housing); Motor Replacement; Carbon Brush Replacement - Panasonic MC-V325 Service Manual

PARTS LIST
(NOZZLE HOUSING)...
Ref. No. Part Name & Description
A – 1 Nozzle Housing ACØ1ACBYZYU2
A – 2 Window AC21HAGZZYØ2
A – 3 Shaft, Plastic AMC25S-VØØ
A – 4 Furniture Guard AC1ØAAGZZVØ7
A – 5 Light Cover AC24HAPPZYU2
A – 6 Bracket, Handle Release AC43AAFY2ØØ
A – 7 Spring, Pedal AC58AAFVZØØ
A – 8 Shaft, Pedal AMC51A-V3Ø
A – 9 Pedal, Handle Release AMC47A-2VØU
A – 10 Screw, Frame AXTN4 +14BFY
A – 11 Screw, Light Cover AXTN4 +16BFY
A – 12 Belt AC28SJPZØØ
A – 13 Nozzle Pipe AC7ØSZA1ØØ
A – 14 Lower Plate Assembly AC91ABAYZVØ6
A – 15 Lower Plate AC27AAFWZVØ6
A – 16 Packing, Lower Plate AC19AARKZVØØ
A – 17 Belt Guard AC43SAFVZØØ
A – 18 Slider Support AC53KAPNZWØ3
A – 19 Screw, Slider Support AXTN4 +16BFY
A – 20 Screw, Nozzle AMC68A-V3Ø
A – 21 Stop Latch Spring AC7ØNYUZØØ
A – 22 Height Adjustment Cam AC61KJPZVØ6
A – 23 Screw, Slider Support AC68AZAZØØ
A – 24 Sliding Knob AC57HJPZVØ6
A – 25 Wheel AC9ØQNGZVØ6
A – 26 Shaft, Wheel AC16CNXZØØ
A – 27 Latch AMC68N-AVØK
A – 28 Screw, Body Lower Plate AXTN4 +16BFY
A – 29 Body, Lower Plate ACØ6AAJUZØØ
A – 30 Screw, Metal Lower Plate AXTS3+10BFY
A
BLOCK
Part No. Quantity Remarks
1
1
1
1
1
1
1
1
1
3 Shipped 10 per package
2 Shipped 10 per package
1
1
1
1 Includes A-16 Packing & A-30 Screws
1
1
1
2 Shipped 10 per package
2 Shipped 10 per package
2
1
1 Shipped 10 per package
1
2
2
2
2 Shipped 10 per package
1
4 Shipped 10 per package
-6-

MOTOR REPLACEMENT

Removal
1. Remove the dust cover.
2. Remove the lower plate, agitator assembly, belt, the plastic shaft, slider support,
light bulb assembly and the nozzle housing as instructed in the respective removal
sections. Remove the plastic holder, (Fig. 15).
3. Turn the vacuum over to the front side.
NOTE: The bumper is positioned over the top of the motor case. Pull up on
the portion of the bumper that lies across the top part of the motor case to
free the motor case for removal.
4. Remove the four (4) screws from the motor case and then remove the motor
case, (Fig. 15).
5. Disconnect the motor leads and remove the motor. Remove the motor support rubber, (rear), noise suppressor, and
the motor support rubber, (front). Place these items on the new motor. See the C Block for a view of these.
Installation
1. Place the motor back into the dust compartment with brushes aligned parallel to the front edge of the dust
compartment. The motor support, (rear) must also align with the tabs in the same direction.
2. Rewire per the Pictorial Wiring Diagram.
3. Replace the motor case and the four (4) screws.
4. Replace the bumper by inserting it into the groove in the dust container.
5. Turn the vacuum back over and replace the plastic holder, thick side out, plastic shaft, slider support, light bulb
assembly, nozzle housing, belt, agitator assembly, and lower plate according to the respective installation instructions.

CARBON BRUSH REPLACEMENT

Removal and Installation
1. After removing the motor, see MOTOR REPLACEMENT, make
sure that you have properly identified it. Note specifically that this
motor is made in the U.S.A. as identified by the label on the side of
the motor, or Made in U.S.A. stamped on the bottom.
2. Remove the amp terminals located on each brush end, (Fig. 16).
Replace the brush assembly which should include the brush holder.
Reinstall the amp terminals onto the new brush assembly. Complete
brush change on one side before starting on the other side.
NOTE: Do not drop screws into the motor.
3. There are two (2) brushes located on the motor as identified in
(Fig. 16). A Phillips head screwdriver will be required to remove the
four (4) screws that hold the brush holders onto the motor. See
(Fig. 16) for screw location.
NOTE: When inserting the brush assembly, be sure that
the TAB on the bottom of the brush holder is positioned in the
trough as shown in Fig. 18.
4. Replace the brush holder bracket with two (2) Phillips screws on
each side of the motor.
5. As a final check to assure proper installation of brushes,
measure across the brushes for the approximate dimension as
shown in (Fig. 17).
Carbon Brushes
Green Ground Wire
(Some Models)
Amp
Terminal
Label
Brush
Screws
Made in U.S.A.
115-120 mm
4.5 - 4.7"
Trough
Brush Holder
Tab Location
Brush to Brush
Dimension is Approximate
-19-
(Fig. 15)
(Fig. 16)
(Fig. 17)